FIRECORE G60 4D Laser Level User Manual

1. Introduction

Thank you for choosing the FIRECORE G60 4D Laser Level. This advanced tool is designed to provide precise horizontal and vertical alignment for various construction and DIY projects. Featuring 16 green laser lines and 4x360° full layout coverage, it offers high visibility and versatility. Please read this manual thoroughly before operation to ensure safe and effective use.

2. Safety Information

WARNING: LASER RADIATION. DO NOT STARE INTO BEAM.

This product is a Class 2 laser product (IEC/EN 60825-1:2014), with a maximum output power of <1mW.
Never look directly into the laser beam or point it at others.
Avoid direct eye exposure to the laser beam.
Do not disassemble the laser level. Repairs should only be performed by authorized service personnel.
Keep the device out of reach of children.
Use only the specified power supply and battery.

3. Package Contents

The FIRECORE G60 4D Laser Level typically includes the following items:

FIRECORE G60 4D Laser Level
Hard Carry Case
Lifting Base (adjustable from 2.5cm to 8cm)
Rotating Base
Wall Bracket
Wall Panel
4000mAh Li-ion Battery
Remote Control (Battery: CR2032, Voltage: 3V)
Charger & Type-C Cord
User Manual

Optional accessories (may be included depending on package):

FD30 Receiver (includes 2*AAA 1.5V batteries)
Adjustable bracket for FD30 receiver

FIRECORE G60 4D Laser Level and included accessories: Hard Carry Case, Lifting Base, Rotating Base, Wall Bracket, Wall Panel, 4000mAh Li-ion Battery, Remote Control, Charger & Type-C Cord, User Manual.

Figure 1: G60 4D Laser Level and Standard Accessories

FD30 receiver, adjustable bracket, and 2 AAA 1.5V batteries.

Figure 2: FD30 Receiver and Accessories

4. Specifications

Feature	Specification
Model	G60
IP Rating	IP54 (Waterproof/Dustproof)
Laser Class	Class 2 (IEC/EN 60825-1:2014), <1mW
Laser Wavelength	505-520nm (Green Laser)
Horizontal/Vertical Accuracy	±1.5mm/7m
Self-leveling Range	±4°
Mounting Thread	1/4''
Leveling Type	Gravity pendulum
Operation Time (All Lines ON)	About 5 hours
Working Range (Radius)	30m (up to 60m with FD30 receiver)
Power Supply	Rechargeable 4000mAh Li-ion Battery
Dimensions (Size)	29.50 * 14.00 * 26.00cm
Net Weight	About 460g
Certifications	CE, FCC, RoHS, WEEE

Dimensions and weight of the Firecore G60 laser level.

Figure 3: G60 Dimensions and Weight

5. Setup

5.1. Battery Installation and Charging

The G60 laser level is powered by a rechargeable 4000mAh lithium battery. Ensure the battery is fully charged before first use.

Battery Installation: Open the battery compartment cover on the device. Insert the 4000mAh Li-ion battery, ensuring correct polarity. Close the cover securely.
Charging: The laser tool can be charged via direct plugging with the provided charger and Type-C cord, or the battery can be charged separately. It can also be powered by a power bank.

Multiple charging methods for the Firecore G60: direct plugging, battery charging, and power bank.

Figure 4: Multiple Charging Methods

Video 1: Unboxing and overview of the Firecore G60 laser level and its components.

5.2. Mounting the Laser Level

The G60 laser level can be mounted using various accessories:

Lifting Base: Use the lifting base for precise height adjustments, especially for floor tiling. It allows the laser line to be as low as 2.5cm from the ground and extend up to 8cm.
Rotating Base: Provides 360° rotation for easy adjustment of horizontal lines.
Wall Bracket: For mounting the laser level on a wall. The wall bracket offers fine-tuning capabilities: 9cm vertical adjustment, 5cm front/rear adjustment, and 2cm left/right adjustment. It features 1/4'' and 5/8'' mounting threads.
Tripod: The 1/4'' mounting thread on the device allows it to be attached to standard tripods.

Laying floor tile with lifting base, showing lowest 2.5cm and highest 8cm positions.

Figure 5: Lifting Base for Floor Tiling

Detailed view of the wall bracket showing fine-tuning adjustments: 9cm up/down, 5cm front/rear, 2cm left/right, and 360 degree fine adjustment.

Figure 6: Wall Bracket Fine-Tuning

6. Operating Instructions

The G60 laser level offers three primary operating modes: Self-leveling, Manual, and Pulse.

6.1. Self-Leveling Mode

To activate, slide the ON/OFF switch to the 'ON' position.
The instrument will automatically self-level within a ±4° range.
If the device is outside its leveling range, the laser lines will flash quickly, indicating it cannot self-level. Adjust the device's position until the lines stabilize.

Laser level in self-leveling mode, projecting a horizontal line close to the ground at 11mm height.

Figure 7: Ground-level Horizontal 360° Line (11mm from ground)

Laser level in self-leveling mode on a tripod, projecting lines on a floor.

Figure 8: Self-Leveling Mode in Use

Laser level projecting four 360 degree lines, covering floors, walls, and ceilings.

Figure 9: 4 x 360° Full Layout Coverage

6.2. Manual Mode

To enter Manual Mode, ensure the ON/OFF switch is in the 'OFF' position.
Press and hold the middle button (usually marked with a lightbulb icon) for about 3 seconds. The left side indicator light will turn green.
In Manual Mode, the laser line flashes slowly, and you can operate the tool at any angle you choose, without self-leveling.
Single-press the middle button to adjust the brightness cyclically; three brightness levels are available.
To turn off the measuring tool from Manual Mode, press and hold the middle button for 3 seconds.

Laser level in manual mode, projecting a diagonal line along a handrail.

Figure 10: Manual Mode in Use

6.3. Pulse Mode (with FD30 Receiver)

Pulse mode extends the working range of the laser level, especially useful in bright conditions or for longer distances, by allowing it to be detected by the FD30 receiver.

Step 1: Enable Pulse Mode on G60: Single-press the middle button on the laser level to enter pulse mode. The right side indicator light will turn green.
Step 2: Turn on FD30 Receiver: Power on the FD30 receiver.

Step 3: Detect Laser Lines: Move the FD30 receiver to search for the laser lines. When the receiver detects the laser lines, it will emit

Related Documents - G60

	FIRECORE G60 Green Beam Self-Leveling 4 x 360 Laser Level User Manual User manual for the FIRECORE G60 Green Beam Self-Leveling 4 x 360 Laser Level. Provides detailed information on product features, operation, safety guidelines, specifications, maintenance, and warranty.
	Firecore Green Laser Level User Manual - Operation, Safety, and Specifications Detailed user manual for the Firecore Green Laser Level. Includes product overview, safety warnings, operation modes, maintenance guide, troubleshooting tips, technical specifications, and warranty information for professional and DIY users.
	FIRECORE 3x360° Line Laser User Manual - Model F94T-XG User manual for the FIRECORE F94T-XG 3x360° Line Laser, covering safety instructions, product overview, operating modes, specifications, maintenance, troubleshooting, and warranty information.
	Firecore 3x360° Line Laser User Manual - F95T-XG Comprehensive user manual for the Firecore F95T-XG 3x360° Line Laser. Includes safety instructions, product overview, operating modes, specifications, maintenance, troubleshooting, and warranty information.
	FIRECORE G50 Green Beam Self-Leveling 3x360 Laser Level User Manual Comprehensive user manual for the FIRECORE G50 Green Beam Self-Leveling 3x360 Laser Level, covering safety instructions, product overview, operating modes, specifications, maintenance, troubleshooting, and warranty information.
	FIRECORE G30 Self-Leveling 360-Degree Cross Line Laser User Manual Comprehensive user manual for the FIRECORE G30 Self-Leveling 360-Degree Cross Line Laser, covering specifications, safety instructions, operation, maintenance, and troubleshooting.