1. Setup and Installation
This section details the proper procedure for installing the Hypa filter into your Lydsto W1 floor scrubber.
- Power Off: Ensure the Lydsto W1 floor scrubber is turned off and unplugged from its power source before beginning installation.
- Locate Filter Compartment: Refer to your Lydsto W1 floor scrubber's main manual to identify the filter compartment. This is typically located near the dirty water tank or the air exhaust.
- Remove Old Filter (if applicable): Open the filter compartment. If an old filter is present, carefully remove it. Note its orientation for correct installation of the new filter. Dispose of the old filter responsibly.
- Insert New Filter: Take the new Lydsto W1 Hypa filter. Align the filter with the compartment, ensuring the mesh side (if visible) faces the direction indicated in your main scrubber manual or matches the orientation of the old filter. Gently push the filter into place until it sits securely.
- Close Compartment: Close the filter compartment cover securely. Ensure it latches properly to maintain an airtight seal.
- Power On: You may now plug in and power on your Lydsto W1 floor scrubber.
2. Operating the Filter
The Hypa filter operates passively as an integral part of your Lydsto W1 floor scrubber's vacuum and air purification system. Once correctly installed, it requires no direct user interaction during the scrubber's operation.
- The filter works to capture fine dust particles, allergens, and other airborne contaminants as air is drawn through the scrubber during its cleaning cycle.
- Proper installation ensures optimal air filtration and helps maintain the efficiency and longevity of your floor scrubber.
3. Maintenance
Regular maintenance of your Hypa filter is crucial for optimal performance of your Lydsto W1 floor scrubber.
Cleaning the Filter
- Frequency: It is recommended to clean the filter after every 5-10 uses, or more frequently if the scrubber is used in heavily soiled environments.
- Procedure:
- Remove the filter from the scrubber as described in the 'Setup and Installation' section.
- Gently tap the filter against a trash can to dislodge loose dust and debris.
- For a more thorough cleaning, rinse the filter under cool, running water. Avoid using hot water or harsh detergents.
- Ensure the filter is completely dry before reinstalling it. Air dry for at least 24 hours. Do not use a hairdryer or other heat sources, as this can damage the filter material.
Filter Replacement
- Lifespan: The Hypa filter typically needs to be replaced every 3-6 months, depending on usage frequency and environment.
- Indicators for Replacement: Replace the filter if you notice a significant decrease in suction power, persistent odors, or visible damage to the filter material, even after cleaning.
- Procedure: Follow the 'Setup and Installation' steps to replace the old filter with a new one.
4. Troubleshooting
If you experience issues related to the filter, consult the following table:
| Problem | Possible Cause | Solution |
|---|---|---|
| Reduced suction power | Clogged or dirty filter | Clean or replace the Hypa filter. Ensure it is completely dry before reinstallation. |
| Unusual odors from scrubber exhaust | Dirty or moldy filter | Clean the filter thoroughly. If odors persist, replace the filter. Ensure the filter compartment is dry. |
| Filter does not fit correctly | Incorrect filter model or improper orientation | Verify you have the correct Hypa filter for Lydsto W1. Check the orientation during installation. Do not force the filter into place. |
| Scrubber making unusual noises | Filter not seated properly or damaged | Remove and re-install the filter, ensuring it is securely seated. Inspect for any damage and replace if necessary. |
5. Specifications
| Feature | Detail |
|---|---|
| Product Name | Hypa Filter for Lydsto W1 Floor Scrubber |
| Model Number | Lydsto W1 |
| Type | Vacuum Cleaner Part (Filter) |
| Material | Plastic |
| Color | Light Grey |
| High-concerned chemical | None |
| Origin | Mainland China |
6. User Tips
- Regular Checks: Periodically check the filter for visible dirt or damage, especially if you use the scrubber frequently or in dusty environments.
- Keep Spares: Consider keeping a spare filter on hand to ensure continuous optimal performance of your Lydsto W1 floor scrubber, especially during drying times after cleaning.
- Gentle Handling: Always handle the filter gently to avoid damaging the delicate filtration material.
7. Warranty and Support
For specific warranty information regarding your Lydsto W1 Hypa filter, please refer to the documentation provided with your Lydsto W1 floor scrubber or contact the original seller/manufacturer directly. As a consumable part, filters typically have a limited or no direct warranty, but defects upon arrival should be reported immediately.
For technical support or inquiries about replacement parts, please contact Lydsto customer service or the retailer from whom you purchased the product.
