1. Introduction
The VDIAGTOOL VD70 Lite diagnostic tool is designed to interface with a vehicle's Electronic Control Unit (ECU), enabling users to retrieve diagnostic trouble codes (DTCs), access real-time data streams, and perform active tests (bi-directional controls). It supports comprehensive diagnostics across multiple vehicle systems—including engine, transmission, anti-lock braking system (ABS), SRS (airbag), chassis, body, and more.
The tool allows simultaneous graphing of up to eight live data parameters on a single screen for efficient analysis and also provides detailed ECU information.
This manual offers an overview of the diagnostic tool's core features, covering control buttons, data ports, battery pack, and power options. Technical specifications are provided at the end of the manual.
2. Safety Information
To ensure your safety and prevent damage to the device or vehicle, please carefully read and follow all instructions in this manual before use.
When operating the device, always verify proper testing procedures and strictly adhere to the instructions provided. As automotive electrical systems may vary, you must assess potential risks and ensure a safe testing environment.
Always observe all safety warnings, use appropriate tools, and disconnect power sources when necessary. Improper operation may result in personal injury, equipment damage, or voided warranty.
2.1 Safety Messages
Safety messages use standardized signal words to indicate hazard levels and prevent injuries or equipment damage:
DANGER: Will result in death or serious injury if ignored. Indicates an immediately life-threatening hazard.
WARNING: Could result in death or serious injury if ignored. Indicates a potentially dangerous situation.
2.2 Safety Instructions
This manual covers known safety hazards, but cannot anticipate all possible risks. You are responsible for ensuring safe operating conditions and procedures.
- DANGER: Always ventilate the service area when the engine is running or use a building exhaust removal system if available. Carbon monoxide is odorless and deadly - can cause loss of consciousness or death.
- WARNINGS:
- Always conduct testing in a safe, controlled environment.
- Wear ANSI-approved safety goggles during all operations.
- Keep all objects away from moving or hot engine components.
- Ensure proper ventilation to avoid toxic exhaust fumes.
- Secure the vehicle in PARK (automatic) or NEUTRAL (manual) with the parking brake engaged.
- Place wheel chocks and never leave the vehicle unattended during tests.
- Exercise extreme caution around ignition systems - hazardous voltages are present.
- Maintain an ABC-rated fire extinguisher within immediate reach.
- Never connect/disconnect test equipment with ignition on or engine running.
- Keep all test equipment clean, dry, and free from contaminants.
- Never operate test equipment while driving - focus solely on testing.
- Strictly follow the vehicle service manual's diagnostic procedures.
- Verify full battery charge and secure DLC connections before testing.
- Never place test equipment near the distributor due to EMI risks.
3. Legal Information
3.1 Trademarks
VDIAGTOOL is a registered trademark of Shenzhen VDIAGTOOL Technology Co., Ltd in the United States and other jurisdictions. All other product names mentioned herein may be trademarks of their respective owners.
3.2 Copyright Information
© 2017 Shenzhen VDIAGTOOL Technology Co., Ltd. All rights reserved.
No reproduction, distribution, or transmission of this manual is permitted without express written authorization from VDIAGTOOL. This prohibition applies to all forms of copying including electronic, mechanical, photocopying, and recording.
3.3 Disclaimer & Liability Statement
All illustrations, specifications, and technical data in this manual are for reference only and subject to change without notice.
For the latest documentation, visit: www.vdiagtool.com/support/downloads
3.4 Limitation of Liability
VDIAGTOOL expressly disclaims all liability for:
- Any direct, indirect, incidental, or consequential damages
- Loss of profits or business interruption
- Product modifications or unauthorized use
This manual does not:
- Modify existing purchase/lease agreements
- Create additional liabilities for VDIAGTOOL
- Constitute additional product warranties
IMPORTANT: Always consult this manual before operation, with special attention to all safety warnings. VDIAGTOOL reserves the right to modify product specifications at any time.
4. Technical Specifications
| Item | Description / Specification |
|---|---|
| Display | 7-inch touch screen, 1024 × 600 resolution |
| Operating System | Android 10.0 |
| Processor | Quad-core, 1.5 GHz |
| Memory | 2GB RAM + 64GB ROM |
| Connectivity | Bluetooth 4.1, Wi-Fi (2.4GHz & 5GHz), Type-C |
| Sensor | Gravity accelerometer, Ambient light sensor |
| Audio | Built-in microphone |
| Speaker | Built-in speaker |
| Camera | 8-megapixel |
| Battery Capacity | 18.25Wh (DC 7.3V, Rechargeable Li-ion, 2500mAh) |
| Tested Battery Life | 3.5 hours (continuous operation) |
| Power Adapter | Input: 100-240V AC, Output: 5.0V⎺3.0A |
| Operating Voltage | 9V–36V |
| Dimensions | 240 × 150 × 36.4 mm (9.45 × 5.91 × 1.43 in) |
| Net Weight | 0.91 kg (2.0 lbs) |
| Gross Weight | 2.2 kg (4.85 lbs) |
| Operating Temperature | 0°C to 40°C (32°F to 104°F) |
| Storage Temperature | -10°C to 50°C (14°F to 122°F) |
| Operating Humidity | <90% RH (non-condensing) |
5. What's In The Box
| Item | Quantity |
|---|---|
| VD70 Lite Diagnostic Tool | 1 |
| Type-C to Type-A Adapter (for PC Connection) | 1 |
| Type-C to Type-C Charger Cable | 1 |
| Power Adapter (US Standard) | 1 |
| Power Adapter (EU Standard) | 1 |
| Power Adapter (UK Standard) | 1 |
| DB15 Main Cable | 1 |
| Color Retail Box | 1 |
| Quick Start Guide | 1 |
| Packing List | 1 |
| Protective Hard Case | 1 |
6. Setup and Initial Configuration
6.1 Getting Started
Ensure the diagnostic tool is adequately charged or connected to an external power source.
Note: The images and illustrations shown in this manual are for reference only and may differ slightly from the physical product.
6.2 Powering On, Off, and Force Restart
- Powering On: To turn on the device, press and hold the power button (located on the top-right side) for 3 seconds. The tool will power on if the battery is sufficiently charged or if it is connected to the AC power adapter. If the battery is completely drained, allow the device to charge for a few minutes before attempting to turn it on.
- Powering Off: To turn off the device, press and hold the power button for more than 3 seconds. The diagnostic tool will shut down automatically.
- Emergency Shutdown: Under normal circumstances, always power off the device using the standard procedure. The emergency shutdown procedure should only be used if the diagnostic tool becomes unresponsive to button input or exhibits abnormal behavior. To perform an emergency shutdown, press and hold the power button for 5 seconds until the device powers off.
Important:
- Always terminate all vehicle communication before powering off the diagnostic tool. Forcing a shutdown during communication may cause errors in the vehicle's ECM on certain models.
- Never disconnect the DB15 main cable while the tool is communicating with the vehicle ECU.
- Using emergency shutdown during active communication with a vehicle ECU may cause ECU malfunctions on certain models.
6.3 Wi-Fi Connection
The diagnostic tool supports connections to both 2.4 GHz and 5.0 GHz Wi-Fi networks.
- Swipe up from the bottom to show the toolbar and tap Home.
- Go to Network & internet and turn on Wi-Fi.
- Tap the Wi-Fi icon, select a network, and enter the password.
Note:
- Wi-Fi is not required for diagnosing most vehicles. It is only necessary for certain brands (e.g., Peugeot) that require online server access during diagnostics.
- If Wi-Fi is unavailable, you can use your phone's hotspot.
- iOS: Enable Allow Others to Join and Maximize Compatibility in Settings > Personal Hotspot.
- Android: Enable the portable hotspot in Settings > Wireless & networks > Tethering & portable hotspot. Set encryption to WPA2 PSK and ensure a connection slot is available.
6.4 Product Activation
When the trial period ends, you must register and activate the diagnostic tool to continue using all diagnostic functions.
- Tap Register.
- Enter your email address.
- Set and confirm your password.
- Agree to the User Terms and submit.
Once the registration complete message appears, the tool is activated. Your login credentials will be saved, and no repeated logins are required for future use.
Note:
If you are unable to register or do not see the activation screen, please contact our support team at support@vdiagtool.com or complete the technical support form on our website www.vdiagtool.com for immediate assistance.
6.5 Password Reset
If you forget your password, tap “New password”, enter your email address, and select "Get verification code”. You will receive a verification code from noreply@service-vdiag-tool.com. Enter the code to reset your password. If the code is not in your inbox, please check your spam folder.
Note:
If you have forgotten the email address used for activation, please email the diagnostic tool's S/N (Serial Number) to support@vdiagtool.com to retrieve your registration details.
6.6 Connecting the Main Cable
The diagnostic tool uses a main cable with a DB15 male connector on one end (for the tool) and an OBDII-16 male connector on the other end (for the vehicle) to establish communication.
To establish communication between the diagnostic tool and the vehicle, please follow the steps below:
- Power on the diagnostic tool.
- Connect the DB15 male connector to the tool's DB15 female port and secure the screws.
- Plug the OBDII-16 male connector firmly into the vehicle's OBDII port.
- Turn the ignition to the "ON" position and launch the diagnostic program.
7. Operating the Diagnostic Tool
7.1 Overview of the Diagnostic Tool Interface
Upon powering on, the diagnostic tool automatically launches the diagnostic application. The main diagnostic screen will appear once the program is loaded.
A hidden toolbar is located at the bottom of the screen. Swipe upward from the bottom edge to temporarily display the toolbar, which remains visible for 3 seconds. Tap the Home button on this toolbar to access the Android home screen of the diagnostic tablet.
7.2 Diagnostic Screen Icons
- Auto Scan: Automatically identifies and decodes the vehicle's VIN, then performs a comprehensive diagnostic scan of all accessible electronic control modules.
- Manual Diagnosis: Select this icon to access the diagnostic menu. From here, you can choose to identify the vehicle automatically by VIN, or manually specify the make, model, year, and other configurations. This section also provides access to the DEMO program and standard OBDII tests.
- Special Function: This section provides access to commonly used vehicle maintenance and service functions, offering practical support for both DIY enthusiasts and professional technicians.
- Report: This section provides access to diagnostic reports, data playback, and data review functions.
- Updates: This section enables you to download diagnostic software updates individually or in batch.
- More: This section allows you to manage user accounts and workshop profiles (where applicable), check subscription status, view firmware information, access the endoscope tool, and open the user manual in PDF format.
- Settings: This section enables configuration of the diagnostic software language, measurement units, and USB mode. It also provides access to OS settings, including volume and display brightness adjustment. Additionally, you can view application version, OS version, diagnostic tool serial number, and VCI number here.
- Remote Control: Select this icon to launch TeamViewer for remote assistance.
- Service Center: This section provides contact information and official social media accounts for customer support and other inquiries.
7.3 Hidden Toolbar Icons
- Screenshot icon: Takes a screenshot on what's on the screen.
- Volume Down icon: Decreases the speaker volume.
- Back icon: Returns to the previous menu or screen.
- Home icon: Returns to the Android home screen.
- Task List icon: Displays all ongoing tasks. Swipe up the respective task screen to kill the task.
- Volume Up icon: Press to increase the speaker volume.
- Diagnostic icon: Press to quickly launch the diagnostic application.
- Screen Recorder icon: Press to start recording the screen and audio. Press again to stop recording.
7.4 Home Screen Applications
The Android home screen provides access to various applications:
- Calendar: Displays the calendar in day, week, or month view.
- Camera: Activates the rear camera to capture images of vehicle components or issues.
- Contacts: Manage your contact list, add new contacts using the "+" icon, or import multiple contacts from a vcf file.
- Clock: Set alarms, timers, use the stopwatch, or view the current time.
- Email: Set up email accounts to send messages or share diagnostic reports.
- Music: Play songs, create playlists, and manage music by albums or artists.
- Sound Recorder: Record and play back audio messages.
- Calculator: Perform basic mathematical calculations.
- ES File Explorer: Manage documents, reports, and other files stored in the device memory.
- Adobe Acrobat: View and manage PDF files. Connect to Dropbox with your accounts.
- Quick Support: Allows our technical team to remotely control the tool to diagnose issues or provide guidance.
- Endoscope: Use a connected endoscope for visual inspection. If no endoscope is connected, the built-in camera will activate automatically.
- Gallery: View screenshots, camera photos, and screen recordings.
- Video: Play recorded videos and screen recordings.
- Explorer: Browse and manage files in internal memory.
- Chrome: Browse the web to search for fault codes and other information.
7.5 Vehicle Diagnostics
Accurate vehicle identification is required for the diagnostic tool to establish communication and perform diagnostics. The identification process is menu-guided—follow the on-screen prompts to enter the necessary information. Specific steps may vary depending on the vehicle's make, model, and year.
You can identify a vehicle using one of the following four methods:
- Auto Scan: Tap the Auto Scan icon on the diagnostic screen. The tool will automatically scan and decode the vehicle's VIN to identify it.
- Manual Diagnosis: Tap the Manual Diagnosis icon on the diagnostic screen to open the vehicle selection menu. Then, tap the icon in the top left corner to access the Auto Scan and Manual Input options. Select Manual Input to enter the 17-digit VIN manually. The tool will decode the VIN and identify the vehicle.
- Automatic Detection: Tap Manual Diagnosis, select the region of the vehicle brand (e.g., Americas), choose the brand (e.g., CADILLAC), and then select Automatic Detection to allow the tool to automatically identify the connected vehicle.
- Manual Selection: If Auto Scan, Manual Input, and Automatic Detection fail to identify the vehicle, use Manual Selection—the most reliable method—to proceed with diagnostics.
Important:
- A common misconception is that the tool cannot diagnose a vehicle if it fails to read or decode the VIN. If Auto Scan fails, try alternative identification methods. Manual Selection remains the most reliable fallback option.
- Auto Scan is not supported on all vehicles. If unsuccessful, please use another identification method.
- Some VINs cannot be decoded. If both Auto Scan and Manual Input fail, try Automatic Detection or Manual Selection instead.
- Automatic Detection is not supported on all vehicle models. If this method fails, please use Manual Selection.
7.6 Diagnostic Functions
After successful vehicle identification, the diagnostic tool can scan and access the vehicle's electronic control systems to retrieve diagnostic trouble codes (DTCs), read PID data (Parameter IDs), view freeze frame information, access ECU details, and perform tests such as active tests (bi-directional controls), and more.
- Read Codes: Displays diagnostic trouble code (DTC) records stored in the vehicle's electronic control modules.
- Clear Codes: Erases both current and historical DTC records, along with related data, from the vehicle's electronic control modules.
- PID Data: Displays real-time PID data from vehicle sensors and control modules. View data in list or graph formats, set custom value thresholds, and monitor up to 8 sensors simultaneously in list, individual graph, or merged graph views.
- Freeze Frame: When a fault code is triggered, the vehicle ECU will save related data at that moment to generate a freeze frame. It is usually used to analyze the root cause that triggers the fault code, together with fault codes and PID data.
- Active Tests (Bi-Directional Controls): Active tests, also referred to as bi-directional controls, verify the operation of specific actuators—including solenoids, valves, and relays.
7.7 OBDII/EOBD Functions
This chapter introduces the concept, protocols, test functions, and basic operations of the OBDII/EOBD feature. To access this function, navigate to: MANUAL DIAGNOSIS → Region Selection → OBDII
OBDII/EOBD provides a fast way to:
- Retrieve DTCs and determine the cause of an illuminated Malfunction Indicator Lamp (MIL)
- Check monitor status before emissions tests
- Verify repairs and perform other emissions-related services
The OBDII function enables access to "generic" OBDII/EOBD data, which is limited to emissions-related diagnostics, including:
- Reading emissions-related Diagnostic Trouble Codes (DTCs)
- Identifying the cause of an illuminated MIL
- Checking monitor status prior to emissions certification testing
IMPORTANT: Generic OBDII/EOBD data is not included in engine system diagnostic data.
Global OBD uses the following five communication protocols:
- SAE J1850 PWM
- SAE J1850 VPW
- ISO 14230-4 (KWP2000)
- ISO 9141-2
- ISO 15765-4 / SAE J2480
To access generic OBDII/EOBD data, follow these steps:
- Select MANUAL DIAGNOSIS on the main diagnostic screen.
- Choose the region of the vehicle manufacturer.
- Click the OBDII icon next to DEMO.
The 10 Modes of OBDII include:
- Mode $01 - Live Data
- Mode $02 – Freeze Frame Data
- Mode $03 - Stored Trouble Codes
- Mode $04 – Clear/Reset Emission-Related Data
- Mode $05 – Oxygen Sensors Test Results
- Mode $06 – On-Board System Tests Results
- Mode $07 – Pending Trouble Codes
- Mode $08 – Control On-Board Systems
- Mode $09 – Vehicle Information
- Mode $0A – Permanent Trouble Codes
8. Maintenance & Special Functions
This chapter introduces various scheduled service and maintenance functions, also referred to as "Special Functions". These functions are typically presented as a series of menu-driven executable commands. By following the on-screen instructions—selecting appropriate options, entering correct values, and performing necessary actions—you will be guided through the complete process of executing each function.
Since vehicle configurations vary by model, specific operation steps for each function are not listed here. In general, please follow the prompts displayed on the tool screen.
8.1 Key Programming
The VD70 Lite includes an intermediate level key programmer for programmable remote control keys and some smart keys. Functions include adding keys, generating keys, and deleting keys.
8.2 Oil Reset
The diagnostic tool allows you to reset the engine oil life system, which estimates the optimal oil change interval based on driving conditions and climate. The oil life reminder must be reset after each oil change so the system can calculate the next service due date.
This function is used in the following scenarios:
- The service lamp is illuminated, indicating required maintenance. After servicing, reset the mileage or time to turn off the lamp and start a new service cycle.
- After an oil change or replacement of oil life monitoring sensors, the service lamp must be reset.
8.3 Electronic Parking Brake (EPB) Reset
The EPB reset function allows you to perform maintenance operations such as resetting the brake system, retracting or releasing brake pistons, and calibrating the G-sensor and vehicle level. It ensures safe and effective servicing of the electronic brake system, including deactivating/activating control systems, assisting with brake fluid procedures, and applying/releasing brakes after replacing pads or discs.
Typical Use Cases:
- After replacing worn brake pads or sensors, a reset is required to clear related fault codes and prevent false warnings.
- A reset is also necessary if the brake pad or wear sensor has been replaced, the brake pad indicator is illuminated, the brake sensor circuit is shorted, or the servo motor has been replaced.
8.4 Steering Angle Sensor (SAS) Calibration
SAS calibration permanently stores the current steering wheel position as the straight-ahead reference in the SAS EEPROM. Before calibration, ensure the front wheels and steering wheel are precisely aligned in the straight-ahead position. The VIN is also read from the instrument cluster and stored in the SAS EEPROM. Upon successful calibration, all SAS fault codes will be cleared automatically.
When to Perform SAS Calibration: After replacing the steering angle sensor, replacing steering mechanical components (e.g., gearbox, column, tie rod, knuckle), performing a four-wheel alignment, or repairing the vehicle body.
8.5 Battery Management System (BMS) Reset
The BMS Reset function enables the diagnostic tool to evaluate the battery state, monitor current, register battery replacement, and activate the vehicle's rest state. This process clears existing low-battery fault information and performs battery matching to ensure accurate power management.
When to Perform BMS Reset: After replacing the main battery, to clear previous fault data and prevent false detection by control modules, or to rematch the control module and monitoring sensor for accurate battery usage tracking, avoiding error messages in the instrument cluster.
8.6 Injector Coding
This function writes the identification code of a fuel injector into the ECU, enabling the ECU to recognize and accurately control the new injector. Injector coding is required after replacing the ECU or an injector to ensure proper cylinder-specific fuel injection control.
8.7 Tire Pressure Monitoring System (TPMS) Reset
This function supports learning, matching, and resetting operations for tire pressure sensors.
When to Perform TPMS Reset: After replacing tires, when troubleshooting tire pressure-related issues, or when the tire pressure sensor signal is lost.
Important Notes:
- Some vehicle models require a TPMS activation tool for sensor matching.
- After resetting, driving for a period may be necessary to clear the fault light.
- Tire pressure imbalance can also trigger the tire pressure warning light.
- This function only works with pre-activated sensors. For new sensors, use a professional TPMS tool.
8.8 ABS Bleeding
The Anti-Lock Braking System (ABS) prevents immediate tire lock-up during braking. Maintaining ABS in optimal condition ensures full braking effectiveness, reduces braking time and distance, prevents skidding and loss of control during emergency stops, improves driving stability and steering control, and minimizes tire wear by avoiding excessive friction with the ground.
When air enters the ABS, the ABS Bleeding function must be used to purge the brake system and restore braking sensitivity.
When to Perform ABS Bleeding: After replacing the front or rear brake distributor pump, severe brake fluid loss, or brake fluid replacement.
8.9 Other Special Functions
- Power Balance: Sequentially disables individual fuel injectors and monitors the corresponding drop in engine RPM to identify underperforming cylinders.
- Seat Calibration: Used to match or configure replaced or repaired seats equipped with memory functions.
- EEPROM: Requires an EEPROM adapter (not included) to read from and write data to EEPROM chips.
- Language Change: Modify the system language displayed on the instrument cluster or control console.
- Transport Mode: Deactivate Transport Mode to fully enable all vehicle systems after factory shipment.
- Control Unit Reset: Resets ECU software to resolve faults from abnormal operating temperatures or voltage fluctuations.
- Throttle: Resets throttle actuators and clears learned values, restoring default settings for precise control.
- A/F Reset: Resets or relearns air/fuel ratio parameters to optimize combustion efficiency.
- HV Battery: Checks the voltage of individual battery packs in hybrid or electric vehicles.
- Gearbox Match: Performs transmission self-learning to improve shift quality after disassembly or repair.
- Crank Sensor Relearn: Performs crankshaft position variation learning to turn off the Malfunction Indicator Lamp (MIL).
- Stop/Start Reset: Enables or disables the automatic Start/Stop feature by modifying hidden settings in the ECU.
- EGR Relearn: Recalibrates the Exhaust Gas Recirculation (EGR) valve after cleaning or replacement.
- A/C Relearn: Performs an AC system recalibration after replacing the AC ECU or actuator, or when ECU memory loss occurs.
- Headlight: Initializes the adaptive headlight system, enabling automatic activation and adjusting lighting angle.
- SRS: Resets the acceleration sensor when replaced or when providing erroneous data to systems such as SRS, anti-theft, or navigation.
- Windows Initialization: Restores power window automatic operation and ECU memory after battery disconnection.
- VGT Relearn: Calibrates newly installed variable geometry turbocharger (VGT) components.
- Coolant Bleeding: Activates the electric water pump following its replacement to ensure proper coolant circulation.
- Suspension: Adjusts the vehicle height sensor and performs level calibration in air suspension systems.
- Tire Size Reset: Resets the tire size configuration in the vehicle system when tires are replaced or upgraded.
- Sunroof Initialization: Performs sunroof matching to recover ECU initial memory and automatic ascending/descending function of power window.
- TCM Oil Reset: Resets the TCM oil life system, which calculates the optimum oil change interval.
9. Settings
This chapter introduces the configuration options for the diagnostic software and tablet device, including language selection, measurement units, USB port mode, and other system preferences.
9.1 Language
To use the diagnostic program in your desired language, please contact our support team and provide the serial number (S/N) of your diagnostic tool to authorize the corresponding language software. After authorization, go to Settings → Language on your diagnostic software and select the target language. Navigate to the Update menu to download the complete software package for the newly set language.
9.2 Unit
This setting offers three unit systems for measuring sensor values:
- Metric Units: Centimeters, kilometers, grams, kilograms, °C, liters, Pa, kPa
- Imperial Units: Inches, feet, yards, ounces, pounds, °F, PSI, miles, gallons
- US Units: Inches, feet, yards, ounces, pounds, °F, PSI, mils, miles
9.3 USB Setting
This option allows you to configure the USB Type-C mode:
- Data Transfer Mode: Enables data transfer between the Android tablet and a PC.
- Expansion Mode: Connect extension accessories (e.g., EEPROM adapter).
9.4 Sound & Display
Adjust the volume of the built-in speaker and the brightness of the display screen.
9.5 Storage Management
This function provides access to manage your device's storage space. Here, you can delete content you no longer need (e.g., diagnostic packages) to free up space.
9.6 About
Displays the app version, OS version, diagnostic tool serial number (S/N), and VCI name. Also allows configuration of operating system settings.
10. Software Updates
This diagnostic tool comes with free lifetime updates and does not require any additional subscription.
To update, connect the device to Wi-Fi or a mobile hotspot. A mobile hotspot is recommended for greater reliability and fewer restrictions compared to home Wi-Fi.
If a "Network abnormal” message appears, try an alternative network, check your router settings, or contact support at support@vdiagtool.com.
To update the software programs, you have two options:
- Option 1: Update All Software Programs: Tap "Update All" at the bottom right of the update screen to update all programs at once.
- Option 2: Update Individual Software Program: Tap the "Update" icon (↑) next to any program to update it individually. If the update is interrupted, tap the icon again to resume.
10.1 Delete Software Program
If the diagnostic tool is running slowly due to limited storage space, you can free up memory by removing rarely used software programs.
To delete a diagnostic software program:
- Go to Manual Diagnosis → Select Region.
- Press and hold the icon of the vehicle manufacturer you wish to remove.
- Tap "Delete" in the menu that appears.
11. More Options
11.1 Profile
This section enables you to manage user account settings, configure workshop details, and review subscription information.
- Account Information: Set your username, register your product via email, reset your password, or log out of the current account to switch to a different one.
- Workshop: Technicians or workshops can enter their workshop name, address, phone number, email, and website. These details will be included in diagnostic reports shared with customers.
- Subscription: View the diagnostic tool's serial number (S/N) and activation start date.
11.2 User Manual
The user manual on the VDIAGTOOL website is updated more frequently than the diagnostic tool app. For the most current version, please visit: www.vdiagtool.com.
11.3 Vehicle Coverage
This function allows you to check the compatibility between your vehicle and the diagnostic tool. However, this is for reference only. For better compatibility confirmation, please provide your device S/N, your vehicle VIN and the desired functions to our tech support team at support@vdiagtool.com.
11.4 Email Settings
To configure your Gmail account for sending diagnostic reports, follow these steps:
- Log in to your Google Account and enable 2-Step Verification by going to Security → 2-Step Verification → Get Started, then adding a backup phone to complete the setup.
- Once enabled, visit https://myaccount.google.com/apppasswords to generate an App Password.
- Enter a custom name (e.g., "VD70 Lite"), click "Generate", then immediately copy and save the 16-character password.
- On your diagnostic tool, swipe up to reveal the toolbar, tap the "@" icon to add a new email account.
- Enter your full Gmail address and paste the 16-character App Password (not your regular password), then tap "Next".
To Share a Diagnostic Report via Gmail: Go to Report, select the target report, and tap “Print PDF Report”. Then, tap the menu icon in the top right corner, choose “Share” → “Email”, and send the report using your Gmail account.
11.5 Printing Settings
To enable the printing service on your diagnostic tool, you must first install a compatible print service app or driver. Please review the following checklist before proceeding with the installation.
11.5.1 Checklist for Installing Printing Service:
- Ensure your printer supports Wi-Fi or Wi-Fi Direct connection.
- Confirm the brand and model of your printer.
- Install a print service app (printer driver) compatible with your printer.
11.5.2 Install Mopria Print Service or Specialized Driver:
To install the printing service via APK file, follow these steps:
- On a computer, visit the Mopria official website at https://mopria.org/ (or your printer manufacturer's website).
- Navigate to Print → Print From Android → Direct Download to obtain the APK file.
- Connect the diagnostic tool to the computer using the provided USB Type-C cable. On the tool, swipe down from the top edge to open the notification panel, select File Transfer.
- Transfer the downloaded APK file to the following folder on the diagnostic tool: VD70 Lite → Internal Shared Storage → Download.
- Disconnect the USB connection. Open ES File Explorer on the tool, go to: Explorer → Local → Home → Download, locate the APK file and tap it to begin installation.
- After installation, go to: Settings → Connected Devices → Connection Preferences → Printing, tap Mopria Print Service, turn the switch ON, select your printer, and accept any connection prompt on the printer's control panel.
11.5.3 For Printer with Wi-Fi Direct:
If your printer supports Wi-Fi Direct, follow the steps below to connect the diagnostic tool directly to the printer:
- Swipe up to open the hidden toolbar menu and tap "Settings".
- Go to Network & internet → Wi-Fi, then select your printer's Wi-Fi network.
- Find the SSID and password on your printer's front display or control panel. If your printer does not have a display, print a network configuration page from the printer to obtain these details.
12. Troubleshooting & FAQs
12.1 Common Issues and Solutions
- Q: Why can't the automatic VIN feature recognize my vehicle?
A: Automatic VIN scanning may not work on all vehicles. This can occur if the VIN is not stored in the ECU, is not yet included in our database, or if the vehicle (such as some Dodge models) uses a command-based communication protocol. Try turning the ignition ON (engine off), manually entering the VIN, or using Manual Selection. - Q: Why can't my diagnostic tool connect to Wi-Fi?
A: Connection issues can arise from several causes. Check router settings (WPA2, no blocked traffic), try a mobile hotspot, or disconnect Wi-Fi extender and connect directly to the main router. If "connect internet to sync your device" appears, check for a time zone mismatch and set to Pacific Time. - Q: The device is not charging when plugged in. The battery is very low (around 10%). What should I do?
A: Please charge the device for at least one hour, then unplug the USB-C cable, press and hold the power button for 15 seconds, release it, and check if the device powers on successfully. - Q: When activating the device, shows error message "registration failure" after entering your email address.
A: This issue is often network-related; please try using a mobile hotspot (recommended) or switching to a different Wi-Fi network, then attempt activation again. - Q: When entering the diagnosis software, error messages such as "license exception" or "Failed" are displayed. How can this be resolved?
A: Please try pressing and holding the diagnosis software icon to uninstall it, then re-download the software from the "Updates" section. If the issue continues, contact our support team at support@vdiagtool.com with your diagnostic tool's serial number (S/N) for further assistance. - Q: I cannot update. I've tried both Wi-Fi and mobile hotspot, but it keeps showing connection failure. What should I do?
A: This issue is commonly caused by network restrictions, such as router firewall settings or regional network limitations. Please check whether your network allows access to the update server. If the problem continues, contact our support team at support@vdiagtool.com for further assistance. - Q: Why can't I find the I/M Readiness function in the menu?
A: To access I/M Readiness, enter Manual Diagnosis, select the region, tap the "OBDII" icon, perform an Auto Scan or manually select the OBDII Protocol, and then choose I/M Readiness from the menu. - Q: Why can't I find live sensor data such as Short-Term/Long-Term Fuel Trim like a generic OBD2 scanner?
A: To access live OBD2 data (including LTFT and STFT), please enter Diagnosis, select the appropriate region, tap the "OBDII" icon, perform an Auto Scan or manually choose the OBDII Protocol, enter Live Data, and then select the desired parameters such as LTFT, STFT, or related terms. - Q: Why can't I find misfire data for my Ford/Dodge/Chrysler/Jeep vehicle?
A: To access misfire data, navigate to Manual Diagnosis → select region → tap the OBDII icon → perform an Auto Scan or manually select the OBDII Protocol → enter On-Board Monitor Test → then choose "Misfire Cylinder Data" or a similar menu option. - Q: How can I export live data as a CSV file?
A: While viewing Live Data, tap the Menu or Export icon, select Custom or set desired parameters, then choose Export to CSV. To locate the exported file, open ES File Explorer, navigate to Internal Storage → diagnosis → csv_records. - Q: Why does the scanner show "report shared successfully," but I don't receive the email?
A: Reports are sent from our email address: noreply@service-vdiagtool.com. Your email provider may block this message. If you use Gmail, try whitelisting our sender address. Also check your spam or junk folder. - Q: Is it possible to install the Google Play Store on the diagnostic tool?
A: This device does not support the Google Play Store. While third-party apps can be manually installed via APK, it is not recommended as it may impact device performance and stability.
12.2 User Tips
- For optimal compatibility and to ensure all functions are available for your specific vehicle, always verify coverage by contacting VDIAGTOOL support with your device's serial number, vehicle VIN, and desired functions.
- When performing key programming, ensure you understand the specific requirements for your vehicle model, as some smart keys may have unique programming procedures.
- If you encounter issues with A/F adjustments or automatic transmission functions, remember that the tool supports a wide range of manufacturers. Consult the vehicle coverage list or support for specific model compatibility.
- For users in South America, the tool supports full-system diagnostics for various regions, including those in North and South America. If you need specific language support (e.g., Spanish or Portuguese), contact VDIAGTOOL support for authorization and software download.
- Always ensure the diagnostic tool's battery is sufficiently charged or connected to a stable power source before starting any diagnostic or maintenance procedure to prevent interruptions.
13. Compliance Information
13.1 Regulatory Compliance Statements
United States (FCC)
FCC ID: 2BE93VDT700
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Interference Guidance: If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Canada (ISED)
IC: 32118-VDT700
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.
Français: Cet appareil contient des émetteurs/récepteurs exempts de licence qui sont conformes aux RSS exempts de licence d'Innovation, Sciences et Développement économique Canada. Son fonctionnement est soumis aux deux conditions suivantes : (1) Le présent appareil ne doit pas produire de brouillage. (2) Le présent appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
13.2 RF Exposure & SAR (FCC & ISED)
This device complies with FCC and ISED Canada RF exposure guidelines. Its radiated output power is below the radio frequency exposure limits. The Specific Absorption Rate (SAR) is measured using standard operating positions with the device transmitting at its highest certified power level. The FCC SAR limit is 1.6 W/kg. The device is designed to operate at multiple power levels to minimize exposure and uses only the necessary power to maintain communication. To ensure compliance with RF exposure requirements, minimize human contact with the antenna during normal operation.
13.3 Additional Compliance (RoHS, CE & UKCA)
- RoHS: This product is compliant with Directive 2011/65/EU on the restriction of hazardous substances.
- CE: This product conforms to the essential requirements of the following European Directives: EMC Directive 2014/30/EU, RED Directive 2014/53/EU, Low Voltage Directive 2014/35/EU.
- UKCA: This product is declared to conform to the essential requirements of the relevant UK statutory instruments and carries the UKCA mark accordingly.
14. Warranty
14.1 Limited Two-Year Warranty
VDIAGTOOL warrants that the VD70 Lite diagnostic tool shall be free from defects in materials and workmanship for a period of two years (24 months) from the date of delivery to the original buyer.
This warranty does not cover any part that has been subjected to misuse, alteration, used for unintended purposes, or operated in a manner inconsistent with the product instructions. The exclusive remedy for any tool found to be defective under this warranty shall be, at VDIAGTOOL's option, repair or replacement of the product. VDIAGTOOL shall not be liable for any consequential or incidental damages arising from the use or inability to use the product.
15. Support & Contact Information
15.1 Product Support & Training Resources
- Official Website: www.vdiagtool.com
- Support Email: support@vdiagtool.com
- US Hotline: +1-213-355-7171
- Online Form: https://www.vdiagtool.com/support/tech-support
15.2 Training Videos
Free product operation videos are available:
- Visit Training Center: https://www.vdiagtool.com/support/training-center
- Select Diagnostic Tools category
- Watch model-specific tutorials
15.3 Service Center
This section provides various ways you can contact us, including warranty claims, technical support, video tutorials, marketing collaboration, business opportunities, and feedback to help us improve diagnostic tools.
Preferred Contact: support@vdiagtool.com
15.3.1 Remote Control
This function allows you to request remote assistance from our technical team. They can directly operate the diagnostic tool to help you with unfamiliar functions or procedures.
To use remote assistance:
- Ensure your diagnostic tool is connected to a Wi-Fi network.
- Tap the "Remote Control” icon to launch TeamViewer.
- Wait until the status "Ready to connect (secure connection)” appears at the bottom left of the screen.
- Provide the TeamViewer ID (displayed in the center-right of the screen) to our support team when scheduling a remote session in advance.
15.3.2 Schedule a Remote Control
To schedule a remote assistance session with our technical team, please follow these steps:
- Visit our official website: www.vdiagtool.com
- Navigate to "Support" → "Tech Support", or directly access: https://www.vdiagtool.com/support/tech-support
- Complete the “Remote Assistance” form with your request and details.
15.4 Data Logging
For software-related issues such as vehicle communication failures or function errors—data logs are often essential for effective troubleshooting. To ensure our technical team can retrieve and analyze these logs, please keep your diagnostic tool connected to Wi-Fi for at least 15 minutes and provide its serial number (S/N) when submitting a support request.
15.5 For Wholesale Business or Distributors
Email: sales@vdiagtool.com
15.6 For Product Innovation & Testing
Email: inventers@vdiagtool.com
15.7 For Social Media Content & Community
Email: marketing@vdiagtool.com
Follow Us on Social Media:
- Facebook Page: Search for "vdiagtool"
- Facebook User Group: Search for "VDIAGTOOL OFFICIAL User Group"
- Instagram: Search for "vdiagtool_official"
- TikTok: Search for "vdiagtool_us"
- YouTube: Search for "Vdiagtool Official"