WINXU SW900 Colour LCD Display Set

Contents

WINXU E-bike Brushless Motor Controller and SW900 Colour LCD Display Set

User Manual

1. Introduction

This manual provides detailed instructions for the installation, operation, maintenance, and troubleshooting of your WINXU E-bike Brushless Motor Controller and SW900 Colour LCD Display Set. Please read this manual thoroughly before use to ensure proper function and safety.

Product Information

  • Product Name: Brushless Motor Controller for E-Bike
  • Model: 250W / 350W / 500W
  • Batch Number: 260215P-01

Manufacturer & EU Representative Info

  • Manufacturer: ShenZhen WinXu Technology Co.,Ltd
  • Address: No.118, Building B, Yongxing Office Building, No. 68, Tianyun Road, Songgang Street, Baoan District, Shenzhen, China
  • EU Authorized Representative: Vermilion Bird OU
  • Address: Tartu mnt 67/1-13b, Kesklinna linnaosa, 10115 Tallinn Harju maakond, Estonia

2. Safety & Warnings

Read all instructions before use to ensure safety and prevent damage.

Warning: Keep the device and its cord out of reach of children under 3 years old.

Important Note: This brushless controller is designed for brushless motors only. It is not suitable for brush motors. Ensure your motor has a Hall sensor; otherwise, the display will show an E07 fault code. If your motor is Hall-less or has a damaged Hall sensor, consider this before purchase, as international returns can be costly.

3. Specifications

AttributeValue
TypeController
Brand NameWINXU
OriginMainland China
Input Voltage24V 36V 48V
Power250W/350W/500W
Controller SizeApprox. 8.8 x 5.2 x 3cm (3.46 x 2.04 x 1.18inch)
Current13A / 15A / 22A
LCD Display ModelWW900/ S886 /G51 /S866 /TF-100 (SW900 Colour Display included)
Motor TypeBrushless Hall Motor
Display SizeApprox. 8 x 5cm (3.15 x 1.97inch)
Low-voltage Protection (24V-36V)19V/30V
Low-voltage Protection (36V-48V)30V-41V
WaterproofRainproof
WeightApprox. 332g

4. Package Contents

The package typically includes the following items:

  • 1 x LCD Display (SW900 Colour Display)
  • 1 x Controller (Brushless Motor Controller)

5. Setup and Installation

5.1 Pre-use Preparation

Before installing the controller, always disconnect the battery power supply. Never work with the power on, as this may damage the equipment.

5.2 Reading the Product Wiring Diagram

Before starting the installation, carefully read the wiring diagram and fully understand the functions of all connectors.

Detailed wiring diagram for WinXu Tech 250W Brushless Controller showing connections for power input, power lock, LED/LCD display, PAS sensor, E-ABS brake, automatic detection, power-off brake, throttle, motor hall, and motor U.V.W.
Figure 1: WinXu Tech LED/LCD Protocol Controller Wiring Diagram for 250W Brushless Controller.
LCD Display Wiring Diagram showing SM-5P connector for LCD display (Red: VCC, Blue: K, Black: GND, Green: RX, Yellow: TX) and SM-2P connector for Headlight (White: GND, Brown: VCC).
Figure 2: LCD Display Wiring Diagram for S866 / G51 / SW900 / S810 displays.

5.3 Connector Function Introduction and Installation Steps Reference

  1. Motor Phase Wire: Connect the 3-phase wires (thick yellow, green, and blue wires) of your motor according to the color code. Ensure a secure connection as these handle high driving current.
  2. Motor Hall Sensor: Connect the motor Hall sensor. This controller uses a 6-wire Hall sensor. Red, yellow, and blue are Hall signal wires; red and black are working voltage cables; white is the motor speed signal cable. Connect according to the correct colors. If your motor has a 5-wire Hall sensor, ignore the white speed signal cable; the controller will automatically obtain the motor speed signal from the Hall signal cable.
  3. LCD Display: This 5-pin connector uses a UART protocol LCD display. Red and black are for operating voltage, blue for controller power control, green is RX, and yellow is TX.
  4. Power Lock: This connector is for a key lock. If your bicycle has a key lock, connect the key lock switch here. If not, you can ignore it.
  5. Throttle: This connector is for a Hall throttle (thumb or twist type). It receives a signal voltage of 1.1-4.2V. Red and black are operating voltage, white is the Hall signal. Connect throttle cables correctly.
  6. PAS Sensor: This controller uses a magnetic pulse type PAS sensor compatible with universal PAS sensors. Red and black are power voltage wires, blue is the pulse signal cable.
  7. EABS (Electronic Automatic Braking System): If your scooter uses an EABS type brake, connect it to this connector. If your brakes are low-level brakes, do not use this connector.
  8. Low-level Brake: This is a power-off braking system that cuts off motor power when applied. Black is the negative wire, white is the brake signal cable. Connect correctly if your brake is a low-level type with 2 cables.
  9. Light Power: This connector outputs battery voltage for devices like headlights, brake lights, horns, and USB chargers. Yellow is the positive terminal, black is the negative terminal.
  10. Battery: This is the device's power supply. Connect positive and negative terminals correctly. Incorrect connection can cause short circuits, overheating, and damage. Connect the battery last, ensuring no short circuits or reverse polarity in other components.
  11. Automatic Detection (Self-Learning Cable): This connector is used for motor matching. After initial installation, use this connector to complete the motor matching process. Turn on the device, lift the motor hub, and plug in this connector. The motor will start. If it drives in the wrong direction, disconnect and reconnect the connector to change direction. Once the motor drives correctly without vibration, disconnect the self-learning cable and test riding.
Controller dimensions showing length 140mm (5.5 inch), width 95mm (3.74 inch), height 30mm (1.18 inch), and 55mm (2.17 inch) for the main body.
Figure 3: Brushless Dual-Mode Controller dimensions.
Comparison of 250W/350W controller size (140mm x 95mm) and 500W controller size (140mm x 130mm), both with 55mm height.
Figure 4: Controller size comparison for 250W/350W and 500W models.
LCD display dimensions showing width 110mm (4.33 inch), height 60mm (2.36 inch), and mounting bracket details with 98mm (3.858 inch) and 85mm (3.346 inch) lengths, and 22mm clamp diameter. Wire length is 1.65m.
Figure 5: SW900 Colour LCD Display dimensions and mounting details.

6. Operation

6.1 About E07 Display (Initial Setup)

After the controller is installed for the first time, it may display the E07 error code because motor matching and parameter detection are not complete. To resolve this, use the self-learning cable to complete the motor matching operation as described in the setup section. Once matching is complete, use the throttle and high-speed gear to drive the motor at high speed. The controller will detect motor parameters and status. If no fault is detected during high-speed driving, the E07 error code will be automatically removed. If it still displays, it indicates insufficient driving speed or a fault with the motor or motor Hall sensor; check the motor.

6.2 LCD Parameter Setting

To enter the setting mode, press and hold the Up/Down button for 3 seconds after switching on.

  • P00: Restore factory settings.
  • P01: LCD backlight brightness.
  • P02: Mileage display unit: 0-KM, 1-MILE.
  • P03: Voltage setting: 24V, 36V, 48V (default 36V).
  • P04: Hibernation time: 0 for no hibernation, otherwise duration in minutes.
  • P05: Pedal assist (PAS) gear.
  • P06: Wheel Diameter (unit: inch).
  • P07: Speed measuring magnet number (range 1-100).
  • P08: Speed limit (range 0 to 50 km/h, 50 means no speed limit).
  • P09: Zero start - 0, non-zero start - 1.
  • P10: Drive mode: 0-pedal PAS drive, 1-throttle drive, 2-PAS and throttle drive.
  • P11: Pedal assist (PAS) sensitivity setting (range 1-24).
  • P12: Pedal assist (PAS) drive strength setting.
  • P13: Pedal assist (PAS) sensor disc type setting (5-8-12 magnet).
  • P14: Controller current limit setting.
  • P15: No function set at this time.
  • P16: ODO clear setting (long press up button for 5 seconds to clear ODO).
  • P17, P18, P19: Not yet set function.

Note:

Except for P03, P06, and P07, other parameters are not recommended to be set by non-professional users to avoid complications. We strongly recommend ordinary users to set only P03, P06, and P07, and to use a dual Hall PAS sensor.

7. Troubleshooting: LCD Error Code Explanation

The LCD display provides error codes to help diagnose issues:

  • E02: Brake fault
  • E03: PAS sensor fault
  • E04: 6KM/H cruise mode
  • E05: Real-time cruise
  • E06: Battery undervoltage
  • E07: Motor failure
  • E08: Throttle fault
  • E09: Controller failure
  • E10: Communication signal reception failure
  • E11: Communication signal transmission fault
  • E12: BMS communication fault
  • E13: Headlight fault

Common Issue: E07 Fault Code

If E07 (Motor failure) persists after initial setup, ensure the motor matching process with the self-learning cable was completed successfully and that the motor has a functional Hall sensor. If your motor is Hall-less, this code will always be displayed.

8. Maintenance & Storage

  • Cleaning: Turn off the device before cleaning. Use a soft, lint-free cloth.
  • Storage: Store in a dry place at room temperature (15°C - 35°C).
  • Long-term Storage: If not used for a long time, charge the device to 50% every 3 months.

9. User Tips

  • Always double-check all connections before powering on to prevent damage.
  • For optimal pedal assist functionality, ensure you are using a dual Hall PAS sensor. If you have a single Hall PAS or no PAS, consider upgrading or purchasing a compatible one.
  • When setting LCD parameters, only adjust P03 (Voltage), P06 (Wheel Diameter), and P07 (Speed Measuring Magnet Number) unless you are a professional. Incorrect settings can lead to operational issues.

10. Disposal & Recycling

This symbol indicates that this product should not be treated as household waste. According to the WEEE Directive (2012/19/EU), it must be disposed of at an appropriate electronic waste collection point for recycling to prevent potential negative consequences for the environment and human health.

11. Warranty & Support

For any technical support or warranty inquiries, please contact your retailer or the manufacturer directly using the contact information provided in the 'Introduction' section of this manual.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.