HOTRC F-06A F-06AT

Contents

HOTRC 6 Channel F-06A / F-06AT 2.4Ghz Receiver Instruction Manual

Models: F-06A (without Gyro), F-06AT (with Gyro)

1. Introduction

This manual provides detailed instructions for the HOTRC F-06A and F-06AT 6-channel 2.4Ghz receivers. These receivers are designed for use with various remote control models, including cars, boats, and tanks. The F-06A is a standard receiver, while the F-06AT includes an integrated gyroscope for enhanced stability (not suitable for aircraft). Please read this manual thoroughly before operating your receiver to ensure proper setup and safe use.

HOTRC F-06A and F-06AT 6-channel receivers
Figure 1: HOTRC F-06A (top, without Gyro) and F-06AT (bottom, with Gyro) receivers.

2. Product Overview

The HOTRC F-06A and F-06AT receivers feature 6 PWM channels, an EXT-V port for external voltage monitoring, and a BIND button for pairing with your transmitter. The F-06AT model additionally incorporates a gyroscope for improved control stability in ground and water vehicles.

F-06A Receiver

Front view of HOTRC F-06A receiver
Figure 2: Front view of the F-06A receiver, showing channel ports and labels.
Detailed diagram of HOTRC F-06A receiver connections
Figure 3: F-06A connection diagram. Shows PWM channels 1-6 (S, +, -), INPUT 4V-9V/DC, EXT-V, BIND button, and Postback Plug. Digital servos are indicated by a bright blue light, analog servos by an extinct blue light.

F-06AT Receiver (with Gyro)

Front view of HOTRC F-06AT receiver
Figure 4: Front view of the F-06AT receiver, indicating the integrated gyroscope.
Detailed diagram of HOTRC F-06AT receiver connections
Figure 5: F-06AT connection diagram. Similar to F-06A, it shows PWM channels 1-6 (S, +, -), INPUT 4V-9V/DC, EXT-V, BIND button, and Postback Plug. Digital servos are indicated by a bright blue light, analog servos by an extinct blue light.

3. Specifications

Below are the detailed specifications for the HOTRC F-06A and F-06AT receivers:

FeatureF-06AF-06AT
Product ModelF-06AF-06AT
Number of Channels66
Wireless Frequency2.4GHz2.4GHz
Receiving DistanceGround 300m, Air 800mGround 300m, Air 800m
Input VoltageDC 4-9VDC 4-9V
Return Voltage0-27V (300M)0-27V (300M)
Working Current35mA39mA
Appearance Size38mm * 24mm * 13mm38mm * 24mm * 13mm
Product Weight7.3g7.4g
GyroscopeNoneYes (Aircraft Not Supported)
Applicable TypeCar / Boat / Aircraft / TankCar / Boat / Aircraft / Tank
Servo ModeDigital / AnalogDigital / Analog
Output Signal6PWM + 1 level signal6PWM + 1 level signal
Frequency MatchingButtonButton
Postback Voltage3.7V-33.6V3.7V-33.6V

4. Setup

4.1. Binding the Receiver to Transmitter

  1. Ensure your transmitter is powered off.
  2. Connect a bind plug (not included, typically comes with your transmitter) to the 'BIND' port on the receiver.
  3. Power on the receiver by connecting it to a suitable power source (DC 4-9V). The receiver's LED indicator should start flashing rapidly, indicating it's in bind mode.
  4. While holding the bind button on your transmitter (refer to your transmitter's manual for exact procedure), power on the transmitter.
  5. The receiver's LED should turn solid, indicating a successful bind.
  6. Release the bind button on the transmitter, then power off both the receiver and transmitter.
  7. Remove the bind plug from the receiver.
  8. Power on the transmitter first, then the receiver. The receiver's LED should be solid, confirming the connection.

4.2. Connecting Servos and Other Components

The receiver has 6 PWM channels (1-6) for connecting servos, ESCs, and other components. Each channel port has three pins: Signal (S), Positive (+), and Negative (-).

  • Servos: Connect your servos to the desired PWM channels. Ensure the correct polarity: Signal wire to 'S', Positive wire to '+', and Negative wire to '-'. Digital servos may show a bright blue light, while analog servos may show an extinct blue light (refer to Figure 3 and 5).
  • Electronic Speed Controller (ESC): Connect your ESC to the appropriate PWM channel (usually channel 2 for throttle). The ESC will also provide power to the receiver.
  • External Voltage (EXT-V): The 'EXT-V' port allows for external voltage monitoring (0-27V). Connect a voltage sensor or battery monitoring device here if desired.
  • Postback Plug: This port is used for telemetry data feedback, such as battery voltage. Connect compatible telemetry modules here.

5. Operating Instructions

5.1. Basic Operation

  1. Always power on your transmitter first, then the receiver.
  2. After use, power off the receiver first, then the transmitter.
  3. Ensure all connections are secure before operating your RC model.

5.2. Gyroscope Function (F-06AT only)

The F-06AT receiver includes an integrated gyroscope to help stabilize your RC model. This is particularly useful for cars and boats to maintain direction and reduce unwanted movements. The gyroscope function is automatically active once the receiver is powered on and bound. It is not recommended for use with aircraft models.

6. Troubleshooting

  • No Signal / Receiver LED not solid:
    • Check if the receiver is properly powered (DC 4-9V).
    • Ensure the receiver is correctly bound to the transmitter. Repeat the binding process if necessary.
    • Verify that the transmitter is powered on and within range.
  • Servos not responding:
    • Check servo connections for correct polarity and secure fit.
    • Ensure the ESC is providing power to the receiver if it's the primary power source.
    • Test servos individually to rule out faulty components.
  • Interference / Erratic behavior:
    • Ensure the receiver antenna is not obstructed or damaged.
    • Avoid operating near strong electromagnetic interference sources.
    • Check for loose wiring or damaged components.

7. User Tips

  • Always perform a range check before operating your RC model, especially in a new environment.
  • Keep the receiver's antenna as straight and unobstructed as possible for optimal signal reception.
  • Regularly inspect all wiring and connections for wear or damage.
  • For F-06AT users, experiment with the gyroscope settings on your transmitter (if available) to fine-tune stability for your specific model.

8. Warranty and Support

For warranty claims, technical support, or further assistance, please contact the seller or manufacturer directly. Keep your purchase receipt as proof of purchase.

Disclaimer: This product can expose you to chemicals including phthalates (DEHP), which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.