GEYA GPS8-03 Voltage / Current Protector

Contents

User Manual: GEYA GPS8-03 Din Rail 3 Phase Voltage and Current Protector

Model: GPS8-03 Voltage / Current Protector | Brand: GEYA

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of the GEYA GPS8-03 Din Rail 3 Phase Voltage and Current Protector. This device is designed to monitor and protect household and industrial equipment from overvoltage, undervoltage, and overcurrent conditions in 3-phase + Neutral electrical systems. It features true RMS measurement, adjustable protection parameters, and automatic reset capabilities.

Front view of the GEYA GPS8-03 Din Rail 3 Phase Voltage and Current Protector
Figure 1: Front view of the GEYA GPS8-03 Protector.
Rear view of the GEYA GPS8-03 Din Rail 3 Phase Voltage and Current Protector showing mounting clips
Figure 2: Rear view showing Din Rail mounting clips.
Comparison of GEYA GPS8-01, GPS8-02, and GPS8-03 models, highlighting voltage and current monitoring and protection
Figure 3: GEYA GPS8 series for Voltage & Current Monitoring + Protection.

2. Safety Information

WARNING: Electrical shock hazard. Installation and maintenance should only be performed by qualified personnel.

  • Always disconnect power before installing or servicing the device.
  • Ensure all wiring connections are secure and comply with local electrical codes.
  • This product does not have an isolation function. Always disconnect the superior Main Circuit Breaker (MCB) during maintenance to prevent electrical shock.
  • Do not operate the device if it appears damaged.

3. Product Overview

3.1 Panel Diagram and Indicators

Panel diagram of GPS8-03 showing indicators for overvoltage, undervoltage, overcurrent, power status, and control buttons
Figure 4: Front Panel Diagram with Indicators and Buttons.

The front panel features digital displays for voltage (V) and current (A) for each phase (L1, L2, L3), along with LED indicators and control buttons:

  • >U Indicator: Overvoltage status.
  • <U Indicator: Undervoltage status.
  • >I Indicator: Overcurrent status.
  • Asy Indicator: Voltage unbalance status.
  • Power Open/Close Indicator (---): Indicates load status.
  • Power Button (circle with line): Manually turn on/off the load. If automatic fault reset is off, use for manual reset.
  • M Button: Press and hold for 3 seconds to enter setting mode. Press and hold for 3 seconds to save settings.
  • Up Arrow Button: Increase value when setting parameters.
  • Down Arrow Button: Reduce value when setting parameters.

4. Specifications

Parameter Value
FunctionOver voltage, under voltage and over current
Rated supply voltageAC220V (L1,L2,L3,N)
Rated Frequency45-65Hz
Operation voltage range80V~400V (L1,L2,L3-N)
Rated operational current63A (AC1)
BurdenAC max.3VA
Over voltage operation valueOFF, 230V-300V (Factory default: 275V)
Under voltage operation value140V-210V, OFF (Factory default: 175V)
Over/under voltage action delay0.1s-10s (Factory default: 0.5s)
Over current valueOFF, 1A-63A (Factory default: 60A)
Over current action delay2s-600s (Factory default: 5s)
Voltage unbalance valueOFF, 20V-99V (Factory default: 40V)
Power up delay2s-600s (Factory default: 5s)
Reset time2s-900s (Factory default: 30s)
Measurement errorless than 1%
Mechanical life (AC1)1 x 106
Electrical life (AC1)1 x 104
Operating temperature-20°C ~ +60°C
Storage temperature-35°C ~ +75°C
Mounting/DIN railDin Rail EN/IEC 60715
Protection degreeIP40 for front panel / IP20 terminals
Operating positionAny
Overvoltage categoryIII
Pollution degree2
Dimensions82 x 72 x 68mm
Weight376g

5. Setup and Installation

5.1 Mounting

The GEYA GPS8-03 is designed for Din Rail mounting (EN/IEC 60715). Ensure the Din Rail is securely installed in a suitable enclosure.

5.2 Wiring Diagram

IMPORTANT: This product does not have an isolation function. Please disconnect the superior Main Circuit Breaker (MCB) during maintenance to prevent electrical shock.

Wiring diagram for GEYA GPS8-03 showing connections to N, L1, L2, L3 inputs and outputs, circuit breakers, and loads
Figure 5: Wiring Diagram for GPS8-03 (3-Phase + Neutral).

Connect the device according to the diagram above. Ensure proper connection of Neutral (N), Line 1 (L1), Line 2 (L2), and Line 3 (L3) for both input and output. The device should be installed after the main circuit breaker and before the loads it is intended to protect.

5.3 Terminal Sectional Area

Based on common industrial standards for devices with 63A rated current, it is recommended to use wires with an appropriate sectional area to handle the current safely and prevent overheating. Consult local electrical codes for specific requirements. For 63A, typically 10-16mm² wire is used, but this can vary.

6. Operation

6.1 Manual On/Off

Diagram showing manual open and close operation, power-on and reset delay, and phase sequence fault display
Figure 6: Operational Diagrams.

Under normal operation, the load can be switched on or off manually by pressing the power key (circle with line) for approximately 0.5 seconds.

6.2 Power-on and Reset Delay

During power-on or after a fault reset, the product will display a countdown according to the set delay time. Once the countdown finishes, it will enter the running state.

6.3 Parameter Setting

To adjust protection parameters:

  1. Press and hold the 'M' button for 3 seconds to enter the setting mode.
  2. Use the 'Up' and 'Down' arrow buttons to navigate through parameters and adjust their values.
  3. Press and hold the 'M' button for 3 seconds again to save the settings and exit the setting mode.

The following parameters can be set:

Parameter Range Step Value Factory Default
Over voltage valueOFF, 230V-300V1V275V
Over voltage recovery value225V-295V1V265V
Under voltage value145V-210V, OFF1V175V
Under voltage recovery value145V-215V1V180V
Voltage fault action time0.1s-10s0.1s0.5s
Over current valueOFF, 1A-63A0.1A60A
Over current action delay2s-600s1s5s
Voltage unbalance valueOFF, 20V-99V1V40V
Power on delay time2s-600s1s5s
Reset time2s-900s1s30s
Phase sequenceON-OFF---OFF
Fault resetON-OFF---ON

6.4 Phase Sequence Fault

If the phase sequence protection function is turned ON, an error in phase sequence access will be indicated on the display (e.g., L1, L3, L2 instead of L1, L2, L3).

6.5 Product Demonstration Video

Video 1: GEYA GPS8-03 Product Overview and Basic Operation. This video demonstrates the device's monitoring capabilities and how it protects against voltage and current anomalies, including a live test with a light bulb.

7. Maintenance

  • Regularly inspect the device for any signs of physical damage or loose connections.
  • Keep the device clean and free from dust and moisture. Use a dry, soft cloth for cleaning.
  • Ensure proper ventilation around the device to prevent overheating.
  • Periodically verify the protection settings to ensure they meet current system requirements.

8. Troubleshooting

The device provides visual indicators for various fault conditions. Refer to the "Functions Diagram" for understanding fault behavior and recovery times.

Functions diagram illustrating overvoltage, undervoltage, voltage unbalance, and overcurrent fault behaviors with LED indicators and timing parameters (Tp, Tr, Tu, Tc)
Figure 7: Functions Diagram for Fault Conditions.
  • Overvoltage/Undervoltage Fault: The corresponding LED (>U or <U) will illuminate. The device will trip and automatically reset after the set 'Reset Time' (Tr) if 'Fault reset' is ON.
  • Overcurrent Fault: The >I LED will illuminate. The device will trip and automatically reset after the set 'Reset Time' (Tr) if 'Fault reset' is ON.
  • Voltage Unbalance Fault: The Asy LED will illuminate. The device will trip and automatically reset after the set 'Reset Time' (Tr) if 'Fault reset' is ON.
  • No Power/Display Off: Check the power supply connections and the main circuit breaker.
  • Device Not Resetting: If the 'Fault reset' parameter is set to OFF, manual reset is required by pressing the power button.
  • Incorrect Readings: Ensure all wiring is correct and terminals are tight. Measurement error is less than 1%.

Timing Parameters:

  • Tp (Power-up delay): 2-600s
  • Tr (Reset delay time): 2-900s
  • Tu (Over/under voltage fault action time): 0.1-10s
  • Tc (Overcurrent fault action time): 2-600s

9. User Tips

  • Terminal Sectional Area: For optimal performance and safety, ensure the wire sectional area matches the 63A rated current. Consult an electrician or local codes for precise recommendations.
  • Operating Modes: The device primarily offers protection based on set voltage and current thresholds with automatic or manual reset. The provided information does not explicitly mention synchronous/asynchronous operating modes for the relay itself, but rather protection functions.

10. Warranty and Support

For warranty information, technical support, or service inquiries, please contact your authorized GEYA distributor or refer to the official GEYA website. Keep your purchase receipt for warranty claims.

GEYA company information including establishment year, annual turnover, headquarters, and product categories like Low Voltage Electrical, Industrial Automation Control, and Solar Energy Equipment. Also shows certifications like CE, CB, SAA, ISO9001, UKCA, RoHS.
Figure 8: GEYA Company Information and Certifications.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.