GEYA GPS6 Voltage / Current Protector

Contents

GEYA GPS6 Series Adjustable Voltage/Current Protector

Models: GPS6-VA5, GPS6-VAK

1. Introduction

The GEYA GPS6 series is a range of adjustable voltage and current protection devices designed for single-phase electrical systems. These devices provide essential protection against overvoltage, undervoltage, and overcurrent conditions, safeguarding connected equipment from potential damage. The GPS6-VAK model further includes Kilowatt-hour (KWH) measuring capabilities for energy monitoring.

This manual provides detailed instructions for the safe installation, configuration, and operation of your GEYA GPS6 protector.

2. Safety Information

WARNING: Electrical shock hazard. Installation and maintenance should only be performed by qualified personnel.

  • Always disconnect power before installing or servicing the device.
  • Ensure all wiring connections are secure and comply with local electrical codes.
  • Do not operate the device if it appears damaged.
  • This device is designed for 220V AC systems. Using it with incompatible voltage may cause damage or malfunction.

3. Product Overview

The GEYA GPS6 series protectors are compact, DIN rail-mountable devices featuring a digital display and intuitive button controls for setting protection parameters.

Front view of GEYA GPS6-VA5 and GPS6-VAK models

Figure 3.1: GEYA GPS6-VA5 (left) and GPS6-VAK (right) models

3.1. Models

  • GPS6-VA5: Adjustable Voltage/Current Protector
    Provides overvoltage, undervoltage, and overcurrent protection. The display shows real-time voltage and current.
  • GPS6-VAK: Adjustable Voltage/Current Protector with KWH Measuring
    In addition to the protection features of the GPS6-VA5, this model also measures and displays Kilowatt-hours (KWH) for energy consumption monitoring.
Angled view of GPS6-VA5 showing Voltage & Current Protection

Figure 3.2: GPS6-VA5 Voltage & Current Protection

Angled view of GPS6-VAK showing KWH Measuring Voltage & Current Protection

Figure 3.3: GPS6-VAK KWH Measuring, Voltage & Current Protection

3.2. Display and Controls

Both models feature a digital display and four control buttons:

  • SET: Enters/exits setting mode and confirms selections.
  • ▲ (Up Arrow): Increases parameter values or navigates menus.
  • ▼ (Down Arrow): Decreases parameter values or navigates menus.
  • O (Power/Reset): Turns the device ON/OFF or manually resets after a trip.

The display shows real-time voltage (V) and current (A). The GPS6-VAK model also shows KWH readings.

A working indicator LED (POWER) shows the device status:

  • Green: Normal operation.
  • Red: Fault condition (overvoltage, undervoltage, or overcurrent).

4. Specifications

Specifications for GPS6-VA5

Figure 4.1: GPS6-VA5 Specifications Overview

Specifications for GPS6-VAK

Figure 4.2: GPS6-VAK Specifications Overview

Technical Data
ParameterGPS6-VA5GPS6-VAK
Supply Terminals (UP)N, L
Rated Supply VoltageAC220V; DC85~300VAC220V
Rated Frequency40~70Hz50~60Hz
Overvoltage (>V) Setting RangeAC130~300V; DC130~300VAC130~300V
Undervoltage (<V) Setting RangeAC80~210V; DC85~210VAC80~210V
Max Operating Current (>A)40A, 63A, 80A (model dependent)
Voltage Hysteresis5V
Voltage Accuracy<1%
Overvoltage Trip Delay5s
Reset Time1~900s (factory default: 30s)
CertificationCE

4.1. Dimensions

Dimensions of the GPS6 device

Figure 4.3: Device Dimensions

  • Overall Height: 86mm
  • Overall Width: 38mm
  • Overall Depth: 46mm
  • Height from DIN Rail: 67.5mm
  • Width on DIN Rail: 35mm

5. Installation

The GEYA GPS6 protector is designed for DIN rail mounting within an electrical enclosure.

5.1. Mounting

  1. Ensure the main power supply is OFF at the circuit breaker.
  2. Snap the device onto a standard 35mm DIN rail.
  3. Ensure it is securely fastened.

5.2. Wiring Diagram

Connect the device according to the following diagram. Ensure correct polarity for Neutral (N) and Live (L) connections.

Wiring diagram for GEYA GPS6 protector

Figure 5.1: Wiring Diagram

  • Input (UP): Connect the incoming Neutral (N) and Live (L) wires from your power source (e.g., main circuit breaker) to the corresponding 'N' and 'L' terminals at the top of the device.
  • Output (OUT): Connect the Neutral (N) and Live (L) wires leading to your load (protected equipment) to the 'OUT N' and 'OUT L' terminals at the bottom of the device.
  • It is recommended to install a circuit breaker upstream of the protector for additional safety and isolation.

6. Operation

6.1. Initial Power-Up

  1. After wiring, turn on the main power supply.
  2. The device display will light up, showing real-time voltage and current. The 'POWER' indicator should be green.

6.2. Setting Parameters

To configure the protection parameters:

  1. Press the SET button to enter the setting mode. The first parameter will start flashing.
  2. Use the ▲ and ▼ buttons to adjust the value of the flashing parameter.
  3. Press SET again to confirm the value and move to the next parameter.
  4. Repeat steps 2 and 3 for all desired parameters.
  5. After setting all parameters, press and hold the SET button for a few seconds to save the settings and exit the setting mode.

Adjustable parameters typically include:

  • Overvoltage Threshold (>V): The voltage level above which the device will trip.
  • Undervoltage Threshold (<V): The voltage level below which the device will trip.
  • Overcurrent Threshold (>A): The current level above which the device will trip.
  • Recovery Time (Reset Time): The delay (1-900 seconds, factory default 30s) before the device automatically resets after a fault condition clears.
  • Voltage Trip Delay (P-7): This setting applies to both overvoltage and undervoltage conditions, defining how long the voltage must be outside the set limits before a trip occurs.

6.3. KWH Measuring (GPS6-VAK only)

The GPS6-VAK model continuously measures and displays the accumulated Kilowatt-hours (KWH). This reading can be viewed on the display. Consult the specific model's detailed instructions for KWH reset procedures if available.

7. Maintenance

  • Keep the device clean and free from dust. Use a dry, soft cloth for cleaning.
  • Regularly check wiring connections for tightness and signs of wear or corrosion.
  • Ensure proper ventilation around the device to prevent overheating.
  • No user-serviceable parts inside. Do not attempt to open or repair the device.

8. Troubleshooting

ProblemPossible CauseSolution
Device does not power onNo input power; incorrect wiringCheck main power supply and wiring connections.
Device trips frequentlyVoltage/current outside set limits; incorrect settingsVerify input voltage/current. Adjust over/undervoltage or overcurrent thresholds. Check recovery time setting.
Display shows 'Red' POWER indicatorFault condition (over/undervoltage, overcurrent)Identify the cause of the fault (e.g., high voltage, low voltage, excessive load). Once the fault clears, the device should reset automatically after the set recovery time, or can be manually reset using the 'O' button.
Cannot change settingsNot in setting mode; buttons unresponsivePress 'SET' to enter setting mode. If buttons are unresponsive, power cycle the device.

9. User Tips

  • Voltage Compatibility: This device is primarily designed for 220V AC installations. While it has a wide DC operating range, ensure your AC system voltage matches the specified 220V for optimal performance and protection.
  • Hysteresis for Stable Operation: The device features a 5V voltage hysteresis. This means if you set an undervoltage trip at 200V, it will not immediately reconnect at 200V but will wait until the voltage recovers to 205V (200V + 5V) to prevent rapid on/off cycling near the threshold.
  • Recovery Time: The adjustable recovery time (1-900s) is crucial. A longer recovery time can prevent damage from intermittent power fluctuations, allowing the system to stabilize before reconnection. The factory default is 30 seconds.
  • Voltage Trip Delay (P-7): This setting helps prevent nuisance tripping from very short voltage spikes or dips. Configure it to a suitable delay to ensure the voltage condition persists for a set duration before the device acts.

10. Warranty and Support

GEYA products are manufactured to high-quality standards. For warranty information, technical support, or service inquiries, please refer to the official GEYA website or contact your authorized dealer. Keep your purchase receipt as proof of purchase.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.