1. Introduction
This document provides instructions for the Teverun dedicated 3-inch TFT high-definition color built-in display. Featuring a high-brightness LCD and a concise user interface, it offers real-time data such as vehicle speed, voltage, power, mileage, gear, and fault codes. Designed for Teverun series electric scooters and electric vehicles, it ensures stable and intuitive data feedback and control support for riding, with waterproof, shockproof, and low power consumption characteristics.

2. Specifications
| Feature | Description |
|---|---|
| Screen Size | 3.0-inch TFT color display |
| Operating Voltage | DC 36V/48V/52V/60V (adaptive) |
| Operating Current | ≤80mA |
| Display Content | Speed, voltage, power, total mileage, single trip mileage, gear, lights, fault code |
| Waterproof Rating | IP54 |
| Installation Method | Built-in embedded installation |
| Communication Method | Standard CAN/RS232 communication (adapted to original vehicle controller) |
| Operating Temperature | -20℃ to 60℃ |
3. Installation and Wiring
- Installation Position: Install the display in the original vehicle's built-in meter position. Use buckles/screws to fix it, ensuring a firm and secure fit without looseness.
- Wiring Instructions (Standard Interface):
- Red wire: Power positive (+)
- Black wire: Power negative (-)
- Green/Yellow wire: Communication signal line
- White wire: Light control line

Detail of the display's wiring connectors. - Power Disconnection: Always disconnect power before installation to prevent short circuits and damage to the meter.
- Wiring Organization: Organize wiring neatly to avoid squeezing, abrasion, and water ingress.
4. Operating Instructions
4.1. Panel and Button Functions
The display typically features 3 or 5 keys, depending on the actual vehicle model.
- M Key (Mode Key):
- Short press: Switches the display interface (e.g., total mileage, single trip mileage, voltage).
- Long press: Enters the settings menu.
- + Key: Increases gear, increases numerical values, navigates up in menus.
- - Key: Decreases gear, decreases numerical values, navigates down in menus.
- Light Key: Controls the front and rear lights (on/off).
- Cruise Key: Long press to enter or exit cruise control.
4.2. Basic Operations
- Power On: After the vehicle is powered on, the display automatically turns on, enters the main interface, and shows normal data after a self-check.
- Gear Switching: Press the + or - keys to switch between gears (e.g., 1/2/3). The number of available gears may vary by model. Higher gears provide more power and a higher speed limit.
- Mileage Switching: Short press the M key to toggle between total mileage (ODO) and single trip mileage (TRIP).
- Clear Single Trip Mileage: While in the single trip mileage interface, long press the M key for 3 seconds to clear the single trip mileage.
- Light Control: Press the Light key. The screen's light icon will illuminate or turn off, simultaneously controlling the vehicle's external lights.
- Cruise Function: Maintain a constant speed for more than 3 seconds, then long press the Cruise key to activate cruise control. To exit cruise control, press any key or squeeze the brake lever.
4.3. Settings Menu Operations
- Enter Settings: On the main interface, long press the M key for 5 seconds to enter the settings menu.
- Menu Selection: Use the + or - keys to navigate up and down through the menu items.
- Parameter Modification: Select an item, then short press the M key to enter its modification mode. Use the + or - keys to adjust the value, then press the M key again to save the changes.
- Exit Settings: After completing your settings, select "EXIT" or long press the M key to return to the main interface.
Configurable items (subject to actual firmware):
- Speed unit (km/h / mph)
- Backlight brightness
- Mileage calibration
- Voltage calibration
- Restore factory settings
5. Maintenance and Upkeep
- Cleaning: Regularly wipe the screen and casing with a soft cloth to keep it clean.
- Connection Check: Periodically inspect all plugs and connectors for looseness, oxidation, or damaged wires.
- Long-term Storage: If the vehicle will not be used for an extended period, it is recommended to turn off the main power to prevent battery drain.
6. Troubleshooting (Fault Codes)
When a fault code appears, the display will beep or flash, and the vehicle's power may be limited. It is recommended to check the corresponding components.
| Fault Code | Description | Action |
|---|---|---|
| E01 | Throttle fault | Check throttle plug and wiring. |
| E02 | Brake fault | Check brake lever switch and wiring. |
| E03 | Controller communication abnormal | Check display and controller connection cable. |
| E04 | Battery undervoltage | Charge the battery in time. |
| E05-E10 | Other system faults | Contact after-sales service for repair. |
6.1. Display Abnormalities (Black Screen, Flickering)
If the display shows abnormalities, a black screen, or flickering, follow these steps:
- First, check the power and communication lines.
- Restart the vehicle.
- Restore factory settings via the settings menu.
- If the issue persists, contact after-sales service.
7. Precautions for Use
- Avoid strong impact, squeezing, and disassembling the display unit.
- Prevent rain from directly washing the screen and interface. Ensure proper waterproofing when washing the vehicle.
- Do not scratch the screen with sharp objects.
- Non-professionals should not modify internal parameters at will.
8. User Tips
- The display is designed for easy installation, fitting like the original part.
- The included NFC cards are functional and work well for security features.
9. Warranty and Support
For warranty information, technical support, or service inquiries, please refer to the official Teverun website or contact your authorized dealer. Keep your purchase receipt as proof of purchase for any warranty claims.