LEEDOAR FNL007

Contents

LEEDOAR FNL007 Pouch Laminator Instruction Manual

Model: FNL007

Introduction

Thank you for choosing the LEEDOAR FNL007 Pouch Laminator. This manual provides essential information for the safe and efficient operation, maintenance, and troubleshooting of your new laminator. Please read this manual thoroughly before using the device and keep it for future reference.

Video: FNL007 Laminator Product Demonstration

Important Safety Instructions

To ensure safe operation and prevent damage to the laminator or injury, please observe the following safety precautions:

  • Heat Warning: The laminator operates at high temperatures. Avoid touching the heated parts during and immediately after use.
  • Keep Hair Away: Ensure long hair is tied back and kept clear of the machine's rollers and openings.
  • Keep Kids Away: This appliance is not intended for use by children. Keep children away from the laminator during operation and storage.
  • Keep Metal Objects Away: Do not insert metal objects, such as paper clips or staples, into the laminator. Remove all metal fasteners from documents before laminating.
  • Keep Ties Away: Loose clothing, ties, or jewelry should be kept clear of the machine's moving parts.
  • Do not use the laminator near water or in damp conditions.
  • Ensure the power supply matches the specifications listed for the device.
  • Unplug the laminator when not in use or before cleaning.
  • Do not attempt to open or repair the laminator yourself. Refer all servicing to qualified personnel.
Safety icons: Heat, Keep Hair Away, Keep Kids Away, Keep Metal Away, Keep Ties Away

Image: Safety warnings for laminator use.

Improper Lamination Methods to Avoid:

Diagram showing incorrect plastic sealing methods

Image: Examples of incorrect lamination practices that can damage documents or the machine.

  • Do not insert film from the protective film opening side.
  • Avoid using the card film at an angle.
  • Ensure the original manuscript and film specifications match.
  • Do not laminate documents that are already in a curly state.
  • Avoid anterior and posterior membrane connections.
  • Do not cut the film before lamination.
  • Do not use deformed protective film over plastic.
  • Ensure plastic parts length is not less than 65mm.

Package Contents

Upon opening the package, please verify that all items are present and in good condition:

  • 1 x FNL007 Laminator
  • 1 x Instruction Manual
Packing list showing FNL007 Laminator and Instruction Manual

Image: Contents of the FNL007 Laminator package.

Specifications

Table of product specifications for FNL007 Laminator

Image: Detailed product specifications.

FNL007 Laminator Technical Specifications
FeatureSpecification
Product NumberFNL007
Product Size417*114*77mm
Net Weight~1430g
Over Molding Width330mm (A3)
Plastic Sealable SizeA3~3 inches
Plastic Thickness≤0.5mm
Plastic Film Thickness80~125mic (0.08-0.125 mm)
Over Plastic Speed355mm/min
Heating MethodQuartz heating wire
Preheat Time≤2 minutes
Constant Temperature Range115~145°C
Film Removal MethodABS button toggle to remove film
Power Supply~400W
VoltageAC220V-240V (Europe/UK), AC110V-120V (US)
Noise≤55db
Number of Rubber Rollers2
CertificationCE, FCC, RoHS, UL
Infographic showing 8 major advantages of the laminator

Image: Key advantages including film sizes, thickness, speed, and modes.

Table of plastic sealing film specifications and sizes

Image: Supported plastic film sizes (3-8 inch, A3-A6).

Setup

  1. Unpack: Carefully remove the laminator and all accessories from the packaging.
  2. Placement: Place the laminator on a stable, flat, and heat-resistant surface, ensuring adequate ventilation around the unit.
  3. Power Connection: Connect the power cord to the laminator and then to a suitable power outlet. Ensure the voltage matches your region's standard (AC220V-240V for Europe/UK or AC110V-120V for US).
  4. Plug Type: The laminator is designed with various plug types (UK, EU, US, CN) to suit different countries. Ensure you have the correct plug for your region.
Laminator with various international plug types shown

Image: Different plug types available for the laminator.

Operating Instructions

Diagram of laminator showing indicator light, paper entrance, and switch button

Image: Key components of the laminator: Indicator Light, Paper Entrance, Switch Button.

1. Power On and Mode Selection

  1. Turn on the laminator using the Switch Button.
  2. Select your desired lamination mode:
    • HOT Lamination: For standard lamination pouches. The red indicator light will illuminate during preheating. Once the laminator reaches the optimal temperature (approx. 1-2 minutes), the light will turn green, indicating it's ready for use.
    • COLD Lamination: For self-adhesive lamination pouches that do not require heat. No preheating is needed for this mode.
Laminator showing quick warm-up and lamination speed

Image: Quick warm-up time (1-2 min) and lamination efficiency (355mm/min).

2. Preparing Documents for Lamination

  • Place your document inside a lamination pouch, ensuring it is centered and there is an even border around the edges.
  • Choose the correct film thickness (80-125mic) for your needs. 80mic is a commonly used thickness with moderate softness and hardness. Note that 1 silk = 1C = 10MIC = 0.01MM. A larger value results in a stiffer feel after plastic sealing.
  • Ensure the document and pouch are free from dust, debris, or wrinkles.
Laminator supporting various film sizes like A3, A4, A5, A6, 3, 4, 5 inches

Image: The laminator supports various film sizes from A3 down to 3 inches. 80MIC thickness is recommended.

3. Lamination Process

  1. Once the laminator is ready (green light for hot mode), carefully insert the sealed edge of the pouch into the Paper Entrance.
  2. The laminator will automatically feed the pouch through. Do not pull or push the pouch during this process.
  3. Once the laminated item exits the machine, place it on a flat surface to cool and harden.

4. ABS Film Removal (Anti-Jam Function)

If a document becomes jammed during the lamination process:

  1. Immediately turn off the laminator.
  2. Locate the ABS button/lever on the side of the machine.
  3. Press and hold the ABS button/lever to release the rollers.
  4. Gently pull the jammed film out of the Paper Entrance.
  5. Release the ABS button/lever and ensure the rollers are clear before resuming operation.
Diagram showing the ABS button for one-click film removal

Image: How to use the ABS button for one-click film removal in case of a jam.

Close-up of the ABS paper release lever on the laminator

Image: Detail of the ABS paper release lever.

Maintenance

  • Cleaning: Ensure the laminator is unplugged and completely cool before cleaning. Wipe the exterior with a soft, dry cloth. Do not use abrasive cleaners or solvents.
  • Roller Cleaning: If you notice debris on the rollers, use a clean, lint-free cloth to gently wipe them. For stubborn residue, a specialized laminator cleaning sheet can be used.
  • Storage: Store the laminator in a dry, dust-free environment when not in use.

Troubleshooting

Here are common issues and their solutions:

Q: Non-stick paper, foggy white block

  • A: 1. Insufficient Preheating: The temperature is not enough. Please wait for the laminating machine to complete preheating (green light) before using it.
  • A: 2. Incorrect Thickness Level: Select a higher thickness level, and then proceed with lamination once the temperature is ready.

Q: The laminating machine does not work or heat up.

  • A: 1. Unsuitable Power Supply: Check the power specifications before turning on the laminator.
  • A: 2. Incorrect Switch Setting: Ensure the switch is set to the 'on' or 'hot' mode.

Q: Bubble spots, wrinkles, and bent photos appear.

  • A: 1. Incorrect Thickness Level: Choose a lower thickness level and wait until the temperature is cooled and ready before plastic sealing.
  • A: 2. Uneven/Debris on Rollers: The rubber roller of the laminating machine may be uneven or have debris. Check the rollers and clean them.
  • A: 3. Improper Item Placement/Debris: The items to be laminated were not placed flat or contained debris. Remove any debris, place the items flat, and then laminate.

Q: What should I do if the plastic paper is jammed?

  • A: 1. Paper Jam/Foreign Matter: If the paper is not fed correctly or there is foreign matter on the rubber roller, turn off the switch and hold down the ABS button to unload the film and clean the rubber roller.

Q: The laminating machine smokes.

  • A: 1. Normal Vulcanization: It is a normal vulcanization phenomenon for new machines. It will disappear after a few more uses.
  • A: 2. Unsuitable Power Supply Voltage: If there is a burning smell, the power supply voltage may not be suitable. Please check the power supply specifications before powering on the laminator.

User Tips

  • For best results, always allow the laminator to fully preheat until the green indicator light appears, especially when using hot lamination mode.
  • When laminating multiple items, ensure consistent film thickness for optimal output.
  • If you frequently laminate different sizes, consider having a variety of film pouches on hand.
  • Always double-check documents for staples, paper clips, or other foreign objects before inserting them into the laminator to prevent jams and damage.

Warranty and Support

For warranty information, technical support, or service inquiries, please refer to your purchase documentation or contact the retailer/manufacturer directly. Keep your proof of purchase for warranty claims.


Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.