1. Introduction
The JIKONG Smart BMS (Battery Management System) is an intelligent protection board designed for large-capacity series lithium battery packs. It offers advanced features such as voltage acquisition, high-current active balancing, overcharge/over-discharge/overcurrent/over-temperature protection, coulomb metering, Bluetooth communication, and optional GPS functionality. This BMS is compatible with Li-ion, LiFePo4, and LTO battery types.
The system utilizes energy transfer active balancing technology with independent intellectual property rights, capable of achieving a maximum continuous 1A/2A balance current. This ensures optimal battery consistency, extends battery life, and delays aging.
The BMS is compact, easy to operate, and full-featured, making it suitable for various applications including small sightseeing vehicles, mobility scooters, shared cars, high-power energy storage systems, base station backup power supplies, and solar power stations.

2. Specifications
2.1. General Parameters (200A Protection Board)
| Parameter | Value | Unit |
|---|---|---|
| Supply Voltage | 20-100 | V |
| Operating Power Consumption | <800 | mW |
| Operating Temperature | -30 to 70 | °C |
| Max. Number of Collection Strings | 24 | Strings |
| Max. Balancing Current | 2 | A |
| Max. Charging Current | 200 | A |
| Max. Discharge Current | 200 | A |
| Max. Instantaneous Current | 400 | A |
| Max. Internal Loop Resistance | 0.275 | mΩ |
| Protective Plate Size | 162*102*20.4 | mm |
| Finished Weight | 560 | g |
2.2. Default Parameters
| Parameter | Li-ion | LiFePo4 | LTO | Unit |
|---|---|---|---|---|
| Balancing Initial Voltage | 3 | 3 | 2 | V |
| Max. Balancing Current | 1-2 | 1-2 | 1-2 | A |
| Single Overcharge Voltage | 4.2 | 3.6 | 2.7 | V |
| Single Overcharge Protection Recovery | 4.18 | 3.55 | 2.65 | V |
| Monomer Undervoltage Protection | 2.82 | 2.6 | 1.8 | V |
| Single Undervoltage Protection Recovery | 2.85 | 2.65 | 1.85 | V |
| Automatic Shutdown Voltage | 2.8 | 2.5 | 1.7 | V |
| SOC-0% Voltage | 2.9 | 2.6 | 1.85 | V |
| SOC-100% Voltage | 4.18 | 3.5 | 2.65 | V |
| Trigger Balancing Differential Pressure | 0.01 | 0.01 | 0.01 | V |
| Charging Overcurrent Protection Delay | 30 | 30 | 30 | S |
| Charge Overcurrent Protection Release Time | 60 | 60 | 60 | S |
| Discharge Overcurrent Protection Delay | 300 | 300 | 300 | S |
| Discharge Overcurrent Protection Release Time | 60 | 60 | 60 | S |
| Short-circuit Protection Delay | 5 | 5 | 5 | µS |
| Short-circuit Protection Release Time | 30 | 30 | 30 | S |
| Charging Overtemperature Protection | 70 | 70 | 70 | °C |
| Charging Overtemperature Recovery | 60 | 60 | 60 | °C |
| Discharge Overtemperature Protection | 70 | 70 | 70 | °C |
| Discharge Overtemperature Recovery | 60 | 60 | 60 | °C |
| Charging Low Temperature Protection | -20 | -20 | -20 | °C |
| Charging Low Temperature Recovery | -10 | -10 | -10 | °C |
| MOS Overtemperature Protection | 100 | 100 | 100 | °C |
| MOS Overtemperature Recovery | 80 | 80 | 80 | °C |
| Device Address | 0 | 0 | 0 | / |
2.3. Physical Dimensions

The dimensions for the JK-BxAxxS-15P/20P series protection board are 162mm (length) × 102mm (width) × 20.4mm (height).
3. Setup and Installation
3.1. Packing List
Before installation, please verify that all components are present:

- BMS Unit (x1)
- Switch (x1, long 50cm)
- NTC Temperature Sensor (x1, long 40cm)
- Sampling Line B (x1, long 70cm)
- Sampling Line A (x1, long 70cm)
- Accessory screws (x4 or x6, depending on model)
3.2. Interface Definition
The BMS features a rich interface to accommodate various communication and monitoring needs. Key interfaces include CAN, RS485, Bluetooth (BT), NTC, Soft Switch, SOC Indicator, Key Switch, and Active Equalizer.

The following table details the pin definitions for the main connectors:
| Connector | Pin No. | Pin Name | Definition |
|---|---|---|---|
| P1 (XH-15AW) Balance & Acquisition Interface | 1 | B- | Total negative battery |
| 2 | B1 | The first battery positive | |
| ... | ... | ... | |
| 15 | B14 | The fourteenth battery positive |
| Connector | Pin No. | Pin Name | Definition |
|---|---|---|---|
| P2 (XH-11AW) | 1 | B15 | The fifteenth battery positive |
| ... | ... | ... | |
| 9 | B23 | The twenty-third battery positive | |
| 10 | B24 | The twenty-fourth battery positive (Total battery positive) | |
| 11 | B+ | Protection board power supply, connected to the battery |
| Connector | Pin No. | Pin Name | Definition |
|---|---|---|---|
| P3 (XH-4AW) Temperature Interface | 1 | T1A | First temperature sensor pin A |
| 2 | T1B | First temperature sensor pin B | |
| 3 | T2A | Second temperature sensor pin A | |
| 4 | T2B | Second temperature sensor pin B |
| Connector | Pin No. | Pin Name | Definition |
|---|---|---|---|
| P4 (A1254WF-4A) Communication Interface | 1 | RS485_B | Negative terminal of RS485 signal |
| 2 | RS485_A | RS485 signal positive terminal | |
| 3 | CAN_H | CAN signal positive terminal | |
| 4 | CAN_L | CAN signal negative terminal |
| Connector | Pin No. | Pin Name | Definition |
|---|---|---|---|
| P5 (1.25T-4PWT) GPS Interface | 1 | VGPS | Power output, voltage close to B+ |
| 2 | TX | UART TX, 3.3V | |
| 3 | RX | UART RX, 3.3V | |
| 4 | GND | Power/signal ground |
| Connector | Pin No. | Pin Name | Definition |
|---|---|---|---|
| P6 (A1254WF-6A) Display Interface | 1 | VCC | Display power output |
| 2 | A | Display RS485 signal positive | |
| 3 | B | Display RS485 signal negative | |
| 4 | GND | Negative terminal | |
| 5 | K+ | Activation signal positive |
| Connector | Pin No. | Pin Name | Definition |
|---|---|---|---|
| P7 (A1254WF-3A) Parallel Interface | 1 | GND | Signal ground |
| 2 | P-EN | Parallel module enable signal (output low level to turn on parallel module) | |
| 3 | P-status | Parallel module status signal |
| Connector | Pin No. | Pin Name | Definition |
|---|---|---|---|
| P8 (A1254WF-2A) Alarm Interface | 1 | VCC | Alarm power supply positive |
| 2 | GND | Alarm power negative |
| Connector | Pin No. | Pin Name | Definition |
|---|---|---|---|
| P9 (A1254WF-5A) Optional ACC Interface | 1 | ACC+ | ACC Positive |
| 2 | ACC- | ACC Negative | |
| 3 | NC | Not connected | |
| 4 | C_Detect+ | Charger output 12V positive | |
| 5 | C_Detect- | Charger output 12V negative |
3.3. Wiring Instructions
The BMS is suitable for 7-24 series lithium battery packs. The wiring method varies depending on the number of cells in the battery pack. Always ensure all cables are connected correctly and securely before powering on the BMS.
General Wiring Steps:
- Connect all balance cables to the BMS.
- Insert the balance cable into the BMS.
- Connect the B-line (total negative electrode) and the P-line (total positive electrode) to the battery.
Important: Incorrect wiring can lead to malfunction or severe damage to the BMS and battery. Double-check all connections.




3.4. APP Installation
The JIKONG Smart BMS is managed via a mobile application compatible with Android and iOS operating systems. To install the APP:
- Scan the QR code below using your smartphone's camera or a QR code scanner app.
- Follow the on-screen instructions to download and install the JIKONG Smart BMS APP.
An Android version 7 or higher is required for the Android APP.

3.5. Device Activation
Before powering on the protection board, ensure the balance cables are properly connected and that the P- and B- lines are correctly wired. Verify that the protection board is securely fixed to the battery pack. Incorrect connections can lead to abnormal operation or damage.
The protection board does not have a power-on control switch. It is designed for charging activation, meaning the charger voltage must be 2V higher than the battery voltage. After the battery assembly is complete, connect the charger to activate the BMS.
Alternatively, if you have an optional display screen and button, insert the cable into the display interface and press the button to activate the BMS.
4. Operating Instructions
4.1. Active Equalization
The BMS employs active equalization to balance cell voltages by transferring energy from higher-voltage cells to lower-voltage cells. To use this feature:
- Set the basic battery parameters (battery type, number of cells, battery capacity) in the APP's parameter settings.
- Adjust the balance trigger pressure difference (mV) in the APP. The default balance current is 1A/2A, which can be adjusted based on battery capacity (recommended not to exceed 0.2C).
- The balancing function will automatically activate when the voltage difference between any two battery strings exceeds the set value and will turn off when the difference falls within the set range.

4.2. Communication Functions
The BMS supports Bluetooth communication for mobile APP connectivity. Optional CAN and RS485 communication functions are also available. These can be selected and configured via the APP's BMS control page, allowing users to set the address and communication protocol according to their specific needs.

4.3. Display and Monitoring
The mobile APP provides a comprehensive view of battery status, including voltage, current, temperature, SOC, alarms, and cycle counts. The APP supports multiple languages and can be switched automatically with the mobile phone system.

Optional external displays are available for real-time monitoring:
- JIKONG 2.5 inch Display: Provides essential battery information.
- JIKONG 3.2 inch Display: Offers a larger view of battery parameters.
- JIKONG 4.3 inch Touch Screen: Advanced display with touch control for detailed monitoring.



4.4. Heating Function (Optional)
For cold environments, the BMS supports an optional heating function. This uses a resistance heater or heating film to warm the battery, preventing performance degradation due to low temperatures. The designed heating current is 10A. Users can enable/disable this function via the APP based on ambient temperature. It is recommended to use a normally closed temperature switch (45°C to 65°C) in series with the heating circuit as a secondary protection.4.5. Parallel Function (Optional)
The BMS supports an optional parallel function for energy storage battery packs. This requires a parallel module and disabling the "disable charging current limiting" function in the APP.
4.6. ACC Detection Function (Optional)
The ACC detection function can enable discharge. It can be activated by applying a voltage between 20V-100V across ACC+ and ACC-, or by directly short-circuiting ACC+ and ACC-. The interface also includes a charger detection function (C_detect+ and C_detect-) for enabling charging based on a 12V voltage signal from the charger.
5. Protection Features
The JIKONG Smart BMS provides comprehensive protection for your battery pack:
- Overcharge Protection: Automatically shuts off charging if any cell exceeds the set overcharge voltage. Charging resumes when all cells fall below the recovery voltage.
- Over-discharge Protection: Disables discharge if any cell falls below the set undervoltage protection value. Discharge resumes when cells are charged above the recovery voltage. An automatic shutdown voltage further protects cells from deep discharge.
- Charge Overcurrent Protection: Triggers if charging current exceeds the set continuous charging current for a specified delay. Charging is disabled and resumes after a recovery time.
- Discharge Overcurrent Protection: Triggers if discharge current exceeds the set continuous discharge current for a specified delay. Discharge is disabled and resumes after a recovery time.
- Overtemperature Protection: Disables charging/discharging if battery temperature exceeds set limits. Operations resume when temperatures return to safe levels.
- Low Temperature Protection: Disables charging if battery temperature falls below set limits. Charging resumes when temperatures rise above recovery levels.
- Short Circuit Protection: Standard feature that triggers if a short circuit is detected. The delay and recovery time can be adjusted via the APP.
- Emergency Switch: In case of critical issues (over-temperature, over-discharge, overcharge, cell drop), activating the emergency switch via the APP will enable charge and discharge for 30 minutes, allowing for emergency use.
- Intelligent Sleep: The BMS can enter an intelligent sleep mode (after 26 consecutive hours of charge/discharge current less than 1A) to reduce self-consumption. It can be reactivated by pressing a button or connecting a charger.
6. Maintenance
The JIKONG Smart BMS is designed for durability and high performance. Its fully aluminum alloy shell provides superior heat dissipation, dustproof, waterproof, anti-voltage, and anti-vibration properties, protecting internal components from external environmental damage.



Regularly check the APP for any alarm notifications or warnings. Keep the firmware updated for optimal performance and security.
7. Troubleshooting
If you encounter any issues with your JIKONG Smart BMS, please refer to the following general troubleshooting steps:
- No Power/Device Not Activating: Ensure all wiring (balance cables, B-, P-) is correct and secure. Verify the battery voltage is within the operating range. If using charging activation, ensure the charger is connected and providing sufficient voltage (2V higher than battery voltage).
- Balancing Issues: Check the active equalization settings in the APP. Ensure the trigger differential pressure is set appropriately. Verify that all cell voltages are being read correctly by the BMS.
- Protection Triggered: If a protection (overcharge, over-discharge, overcurrent, over-temperature, etc.) is triggered, the BMS will disable the corresponding function. Check the APP for specific alarm messages. Address the underlying cause (e.g., reduce load, allow cooling, charge battery) for the protection to reset.
- Communication Problems: If the Bluetooth APP cannot connect, ensure Bluetooth is enabled on your device and the BMS is within range. If using RS485 or CAN, verify the wiring and communication protocol settings in the APP.
- Inaccurate Readings: If voltage or current readings appear incorrect, perform a voltage and current calibration via the APP's parameter settings.
For detailed diagnostics and advanced parameter adjustments, consult the JIKONG Smart BMS APP. The APP allows you to freely adjust multiple protection values such as overcharge, over-discharge, overcurrent, temperature, and balance. Always read the internal parameters of the protection board first before making changes.
8. User Tips
- CAN Cable for Inverter Connection: If you plan to connect your BMS to an inverter using a CAN cable, ensure you purchase a compatible CAN cable from JIKONG or a reputable supplier. Verify the CAN protocol settings in the BMS APP match your inverter's requirements.
- Parameter Adjustment: While the APP allows extensive customization, it's recommended to understand the default parameters and their implications before making significant changes. Incorrect settings can affect battery performance and safety.
- Regular Monitoring: Periodically check the battery status via the mobile APP or an external display to ensure optimal performance and detect any potential issues early.
9. PDF User Manual Reference
For a more in-depth understanding of the JIKONG Smart BMS, including detailed technical diagrams and advanced configuration options, please refer to the official PDF user manual. This document provides comprehensive information beyond what is covered here.
The user manual (PDF) can be accessed via the following link: JIKONG Lithium Battery Active Balance Protection Board Maintenance Manual (PDF)