Kllisre X99 Motherboard Combo Kit

Contents

Kllisre X99 Motherboard Combo Kit User Manual

Model: X99 Motherboard Combo Kit

Introduction

This manual provides detailed instructions for the installation, setup, and maintenance of your Kllisre X99 Motherboard Combo Kit. This kit includes a Kllisre X99 motherboard, an Intel Xeon E5 2680 V4 CPU, and 16GB DDR4 2133MHz ECC memory. Please read this guide thoroughly before beginning the installation process to ensure proper setup and operation.

Kllisre X99 Motherboard Combo Kit with CPU and RAM
Figure 1: Kllisre X99 Motherboard Combo Kit, showing the motherboard, Intel Xeon E5 2680 V4 CPU, and 16GB DDR4 ECC RAM.

Safety Precautions

Always observe the following safety guidelines to prevent damage to components and ensure personal safety:

Electrostatic Discharge (ESD) Protection

  • Always use anti-static measures.
  • Touch a grounded metal object (e.g., unpainted metal part of your PC case) before handling components.
  • Avoid working on carpeted surfaces, which can generate static electricity.
  • Keep components in anti-static bags until they are ready for installation.

Handling Components

  • Never force components into place. If a component does not fit easily, recheck its orientation and compatibility.
  • Handle components by their edges only, avoiding contact with pins, connectors, or circuit boards.
  • Keep your work area clean and organized to prevent misplacement of small parts.
  • Use proper tools for installation, such as a Phillips #2 screwdriver.

Pre-Installation Preparation

Tools Required

  • Anti-static wrist strap (recommended)
  • Thermal paste (if not pre-applied on your CPU cooler)
  • Screwdriver (usually Phillips #2)
  • Flashlight (for better visibility in tight spaces)

Workspace Setup

  1. Choose a clean, well-lit, static-free environment.
  2. Use an anti-static mat or work on a non-conductive surface.
  3. Wear an anti-static wrist strap connected to a grounded object.
  4. Keep all components in their anti-static bags until immediately ready for use.

Component Verification

  • Confirm CPU socket compatibility (LGA 2011-3 for this kit).
  • Verify motherboard BIOS supports the CPU model (usually pre-configured for combo kits).
  • Check RAM compatibility with the motherboard's Qualified Vendor List (QVL) if using different RAM. This kit includes compatible DDR4 ECC memory.

Component Installation

1. CPU Installation

  1. Open CPU Socket: Locate the LGA 2011-3 CPU socket on the motherboard. Gently lift the socket lever to the vertical position. Remove the plastic socket cover if present.
  2. Align CPU: Identify the triangle marker on the CPU (usually a gold corner). Match this with the corresponding triangle marker on the socket. For LGA sockets, the CPU has no pins; the pins are in the socket.
  3. Place CPU: Hold the CPU by its edges only, avoiding contact with the gold contacts on the underside. Gently lower the CPU into the socket without force. Ensure the CPU sits flat with no gaps.
  4. Secure Socket: Carefully lower the socket lever. Press down until it clicks into place. Verify the CPU is securely locked.

Important Notes:

  • Never force the CPU into the socket.
  • Do not touch CPU contacts or socket pins.
  • Handle the CPU by its edges only to prevent damage.

2. CPU Cooler Installation

This section covers general cooler installation. Always refer to your specific CPU cooler's manual for detailed instructions.

Stock Cooler Installation (if applicable)

  1. Apply Thermal Paste: Apply a pea-sized amount of thermal paste to the center of the CPU. If your cooler has pre-applied paste, skip this step.
  2. Position Cooler: Align the cooler with the mounting holes on the motherboard. Ensure the retention mechanism matches the LGA 2011-3 socket type.
  3. Secure Cooler: Attach clips or screws in a diagonal pattern to ensure even pressure. This helps spread the thermal paste uniformly.
  4. Connect Fan: Connect the CPU fan cable to the "CPU_FAN" header on the motherboard. Ensure cable routing does not interfere with other components or fans.

Aftermarket Cooler Installation

  • Follow manufacturer-specific instructions provided with your aftermarket cooler.
  • Some coolers may require a backplate installation.
  • Check for clearance with RAM modules and other components before final installation.

3. RAM Installation

RAM installation note for Kllisre X99 motherboard
Figure 2: RAM installation note, indicating that the green RAM slots must be populated first. The black RAM slots cannot work alone.

Note: The green RAM slots must be installed with RAM. The black RAM slots of the motherboard cannot work alone.

All RAM needs to be installed preferentially in slot 3 and slot 4 (green slots).

  1. Identify Slots: The Kllisre X99 motherboard has 4 DDR4 memory slots. For optimal configuration, refer to the following:
    • When 1 RAM module is used: Install in slot 3 or slot 4 (green slots).
    • When 2 RAM modules are used: Install in slot 3 and slot 4 (green slots).
    • When 3 RAM modules are used: Install in slot 3, slot 4, and slot 1 or slot 2.
    • When 4 RAM modules are used: Install all slots.
  2. Align Notch: Match the notch on the RAM module with the key in the memory slot. Ensure correct orientation.
  3. Insert RAM: Apply firm, even pressure on both ends of the RAM module until it clicks into place.
  4. Verify Installation: Ensure the retention clips on both sides of the slot snap shut, securing the RAM module.

Configuration Tips

  • For dual-channel operation: Install RAM in matching colored slots (green slots first).
  • Check the maximum supported frequency in the BIOS after installation.

4. Motherboard Mounting

  1. Install I/O Shield: Insert the motherboard's I/O shield into the rear opening of your PC case from the inside. Ensure proper alignment with the ports.
  2. Position Standoffs: Install brass standoffs in your PC case that align with the mounting holes on the Kllisre X99 motherboard. Use only the necessary standoffs to avoid creating shorts.
  3. Mount Motherboard: Carefully lower the motherboard onto the installed standoffs.
  4. Align I/O Ports: Ensure all I/O ports on the motherboard align correctly with the openings in the I/O shield.
  5. Secure with Screws: Secure the motherboard to the standoffs using screws. Do not overtighten.

5. Cable Management

  • Route cables behind the motherboard tray of your PC case when possible to improve airflow and aesthetics.
  • Avoid blocking airflow or components with poorly routed cables.

6. Power Connections

Kllisre X99 Motherboard with labeled power connectors
Figure 3: Kllisre X99 Motherboard showing locations of 24-Pin DC (ATX), 8-Pin DC (CPU), and SATA 2.0 power connectors.

Essential Connections

  • 24-pin ATX power: Connect the main power cable from your power supply to the 24-pin connector on the motherboard.
  • 8-pin CPU power: Connect the 8-pin CPU power cable (EPS12V) from your power supply to the connector usually located near the CPU socket.
  • PCIe power: If installing a graphics card, connect the necessary PCIe power cables from your power supply to the graphics card.
  • SATA power: Connect SATA power cables to your storage devices (SSDs/HDDs).
  • Peripheral power: Connect any additional peripheral power cables as needed for other components.

Connection Tips

  • Connect all required power cables before powering on the system.
  • Ensure all connectors are fully seated and locked into place.
  • Verify there are no loose cables near fans or other moving parts.
Kllisre X99 Motherboard with labeled front panel headers
Figure 4: Kllisre X99 Motherboard showing locations of front panel headers (Reset SW, HDD-LED, Power SW, Power-LED).

Connect your case's front panel connectors (Power Button, Reset Button, HDD LED, Power LED) to the corresponding pins on the motherboard's front panel header. Refer to your case manual for specific pin assignments if needed, though the motherboard usually has labels.

Post-Installation Checks

Visual Inspection

  1. Verify all components are securely installed.
  2. Check for any loose screws or tools inside the case.
  3. Ensure cables are clear of moving parts (e.g., fan blades).
  4. Confirm all power connectors are attached correctly.

First Power-On

  1. Connect a monitor to your graphics card (or integrated graphics if available, though this CPU does not have integrated graphics).
  2. Press the power button on your PC case.
  3. Observe the system for signs of life (fans spinning, lights, display output).
  4. Listen for POST (Power-On Self-Test) beep codes. Consult your motherboard manual if you hear unusual beeps.
  5. Check that the CPU fan is spinning.

BIOS Configuration

  1. Enter the BIOS/UEFI setup by pressing the designated key during startup (usually Del or F2).
  2. Verify that the CPU and RAM are detected correctly.
  3. Check system temperatures and voltages to ensure they are within safe operating limits.
  4. Enable XMP/DOCP for RAM overclocking if desired and supported by your RAM.
  5. Set the boot order to your preferred storage device (e.g., NVMe SSD, SATA SSD/HDD).

Operating Your System

Once the system is assembled and passes initial checks, you can proceed with operating system installation and driver setup. Ensure you install the latest drivers for your motherboard chipset, graphics card, and other peripherals for optimal performance and stability.

Maintenance Tips

  • Clean dust from components regularly using compressed air to prevent overheating.
  • Reapply thermal paste to the CPU every 1-2 years, or if you remove the CPU cooler for any reason.
  • Update BIOS for better compatibility and performance. Check the manufacturer's website for the latest BIOS versions.
  • Monitor temperatures of your CPU, GPU, and other components during operation using monitoring software.

Troubleshooting Tips

  • System doesn't POST (Power-On Self-Test):
    • Check all power connections (24-pin ATX, 8-pin CPU, GPU power).
    • Verify the CPU is properly seated in its socket.
    • Ensure RAM modules are fully inserted and seated correctly in the green slots first.
    • Check all other connections (front panel, SATA, etc.).
    • Consult your motherboard manual for specific POST error codes if available.
  • No display output:
    • Ensure your monitor is connected to the graphics card (if installed) and not the motherboard's I/O.
    • Check that the graphics card is properly seated in its PCIe slot and has power.
    • Try reseating RAM modules.
  • System instability/crashes:
    • Check temperatures to ensure components are not overheating.
    • Verify all drivers are up to date.
    • Run memory diagnostic tools to check for RAM issues.

Specifications

Kllisre X99 Motherboard

Kllisre X99 Motherboard with HM55 Chipset and NVMe M.2 slot
Figure 5: Kllisre X99 Motherboard highlighting the HM55 Chipset and NVMe M.2 slot.
Kllisre X99 Motherboard dimensions
Figure 6: Kllisre X99 Motherboard with dimensions: 216mm x 190mm.
Feature Specification
Main ChipsetHM55
CPU SocketLGA 2011-3
Memory Sockets4 x DDR4 Dual Channel
Max Memory Capacity128 GB (4x32GB DDR4)
Supported Memory TypeDDR4 ECC REG (Server Memory)
EthernetOne Realtek Gigabit Ethernet card (1000Mbps)
USB Interfaces6 x USB 2.0 ports (Back I/O: 4 x USB 2.0, PS/2)
PCIe Slots1 x PCIe x16 (PCI-E 3.0), 1 x PCIe x1
SATA Ports4 x SATA 2.0 ports
M.2 Slots1 x M.2 (NVMe)
Audio Channels5.1
Dimensions216mm x 190mm
ApplicationDesktop (Gaming, Household, Office)
Quality CertificationCE
RAID SupportedNo
Kllisre X99 Motherboard rear I/O ports
Figure 7: Kllisre X99 Motherboard rear I/O ports, including PS/2, USB 2.0*6, Gigabit Ethernet, and Audio ports.

Intel Xeon E5 2680 V4 CPU

Feature Specification
Processor SeriesXeon E5 2680 V4 SR1XS
Cores/Threads14 Cores / 28 Threads
Main Frequency2.4GHz (up to 3.3GHz Turbo)
3rd Level Cache35MB
Technology14nm
Power Consumption (TDP)120W
Processor CompatibilityIntel Xeon

DDR4 16GB ECC Memory

Feature Specification
TypeECC REG (Server Memory)
FrequencyDDR4 2133MHz
Capacity16GB (1x16GB)
Memory ChannelDouble

User Tips

  • Check Package Contents: This kit typically includes the motherboard, CPU, and RAM. Upon arrival, verify all components are present as described.
  • Motherboard Battery: The CMOS battery (CR2032) on the motherboard is usually removed before shipping due to international shipping regulations. You will need to install a new CR2032 battery before first use.
  • RAM Slot Priority: Always populate the green RAM slots (slots 3 and 4) first for single or dual module configurations. The black slots cannot function independently.

Warranty and Support

Warranty Information

The CPU and Memory included in this kit are used components and come with a 1-year warranty from the seller. The motherboard is new and typically covered by the seller's warranty terms.

Support Resources

  • Motherboard Manual: For specific details not covered in this general guide, consult the detailed motherboard manual (if provided separately or available online).
  • Manufacturer Websites: Visit the official Kllisre website or the CPU TOP Store on AliExpress for updated drivers, BIOS versions, and additional support.
  • Community Forums: Online PC building communities can be a valuable resource for troubleshooting and advice.
  • Technical Support: Contact the seller's technical support if you encounter persistent issues that cannot be resolved using this manual or other resources.

A user manual in PDF format may be available for more detailed instructions. You can often find it linked on the product page or by searching the seller's store.

© 2023 Kllisre. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.