70mai Jump Starter PS01 & PS06 User Manual

1. Introduction

This manual provides essential information for the safe and effective use of your 70mai Jump Starter (models PS01 and PS06). These devices are designed to jump start 12V vehicle batteries and serve as portable power banks for electronic devices and car accessories. Please read this manual thoroughly before operation.

Image: 70mai Jump Starter models PS01 and PS06.

2. Safety Information & Warnings

Failure to follow these safety instructions may result in electric shock, explosion, fire, and/or injury.

• The device must not be used in place of a car battery.
• Do not use the device as a toy. Keep out of reach of children and supervise any children around the device.
• The device is intended for jump starting a 12V car battery only.
• Use only the provided battery clips. Do not use if the battery clip or cable is damaged.
• Do not connect the positive and negative ends of the battery directly.
• Ensure connections are free of rust and foreign objects before jump starting. Connect securely to prevent poor connection.
• After a successful jump start, disconnect the device from the car battery within 30 seconds to prevent damage.
• Do not use the device for more than 3 consecutive times. Allow a 2-minute interval between multiple jump starts to prevent overheating.
• Do not use the clips to charge any other devices.
• Do not place the product in an environment where the temperature exceeds 60℃.
• Charging should be done at room temperature of between 0℃ to 45℃.
• Do not expose the device to rain or submerge it in water.
• Do not place the device in extreme heat or in a fire.
• Do not use the product in an environment with explosion risk, such as near flammable liquids or gases, or in the presence of dust.
• Before using, ensure someone is near enough to hear you or provide assistance.
• Remove any metallic objects (rings, bracelets, necklaces) from your body before use.
• To reduce risk of damage to the power plug and cable, disconnect using the battery clip plug.
• Do not use damaged or modified batteries.
• Use the provided charging cable or one of similar specification.
• Do not charge the device immediately after jump starting a car battery.
• Do not use the device to jump start a car battery while it is being charged.
• In extreme cases, fluid may leak from the battery. If contact occurs, wash immediately with soap and water. If fluid gets in eyes, wash with cold water for at least 10 minutes and seek medical attention.

3. Product Overview

3.1. 70mai Jump Starter PS01

The PS01 model features a 11,100mAh battery capacity and a peak current of 600A, capable of jump starting 3.0L vehicles up to 40 times on a single charge. It is designed for 12V vehicles with up to 4.0L gas and 2.0L diesel engines.

Image: 70mai Jump Starter PS01 highlighting its features.

3.2. 70mai Jump Starter Max PS06

The PS06 model offers a larger 18,000mAh battery capacity and a powerful 1000A peak current. It is suitable for all 12V vehicles with up to 8.0L gasoline and 3.5L diesel engines, including cars, vans, pickup trucks, SUVs, and motorcycles.

Image: 70mai Jump Starter Max PS06 highlighting its features.

4. Packing List

4.1. 70mai Jump Starter PS01 Package Contents

• 70mai Jump Starter x1
• Charging cable x1
• Smart battery clip x1
• Storage bag x1
• User manual x1

Image: PS01 package contents including jump starter, cables, clip, bag, and manual.

4.2. 70mai Jump Starter Max PS06 Package Contents

• 70mai Jump Starter Max x1
• Charge cable x1
• Smart battery clip x1
• Bag x1
• DC cable x1
• User manual x1

Image: PS06 package contents including jump starter, cables, clip, bag, DC cable, and manual.

5. Setup & Charging

5.1. Initial Charging

Before first use, fully charge your 70mai Jump Starter. The device takes approximately 8 hours for a full charge. Ensure charging is done at a temperature between 0℃ and 45℃.

5.2. Connecting for Jump Start

Connect the smart battery clip to the jump starter unit. The unit will indicate its readiness for use.

6. Operating Instructions

6.1. Jump Starting a Vehicle

1. Connect the smart battery clip to the 70mai Jump Starter.
2. Open your vehicle's hood and locate the battery terminals.
3. Connect the red (positive) clamp to the positive (+) terminal of the vehicle's battery.
4. Connect the black (negative) clamp to the negative (-) terminal of the vehicle's battery.
5. Press the 'Boost' button on the jump starter unit (if applicable, or ensure it's powered on).
6. Start your vehicle.
7. Once the vehicle starts, immediately disconnect the clamps from the battery terminals, then disconnect the smart battery clip from the jump starter unit within 30 seconds.

Image: Easy 3-step process for jump starting a vehicle.

6.2. Using as a Power Bank

The 70mai Jump Starter can charge various electronic devices via its USB output (5V/2.4A). Simply connect your device using a compatible USB cable.

Image: The jump starter acting as a power bank for smartphones, tablets, and other electronics.

6.3. Powering Car Accessories (PS06 only)

The PS06 model includes a 12V power outlet, allowing it to power various car accessories such as air compressors, car fridges, or car DVD players. Connect the accessory using the provided DC cable.

Image: 70mai Jump Starter Max PS06 powering a 70mai Air Compressor and other car accessories.

6.4. LED Light Functions

The built-in LED light offers three modes for various situations:

• Normal Mode: For general illumination.
• Flashing Mode: For signaling or attracting attention.
• SOS Mode: For emergency signaling.

Image: The jump starter's LED light with Normal, Flashing, and SOS modes.

7. Maintenance

7.1. Storage

When not in use for extended periods, store the jump starter in a cool environment, away from direct sunlight. Avoid temperatures above 60℃. The device is designed to retain approximately 85% of its charge after one year of storage.

Image: Illustration of the jump starter retaining 85% power after one year of storage.

7.2. Cleaning

Wipe the device with a dry, soft cloth. Do not use harsh chemicals or abrasive cleaners.

8. Troubleshooting

8.1. Smart Protection Features

The smart battery clamps are equipped with multiple intelligent protection functions to ensure user safety and prevent damage to the unit:

• Short-circuit protection
• Over-current protection
• Overheated protection
• Over charge protection
• Reverse connection protection
• Over-voltage protection
• Reverse charging protection
• Over-discharge protection

Image: List of safety features integrated into the smart battery clamps.

8.2. Common Issues

• Device not turning on: Ensure the device is charged. If not, connect it to a power source.
• Vehicle not starting: Check that the battery clamps are securely connected to the correct terminals. Ensure the vehicle's battery terminals are clean and free of corrosion. The vehicle's battery might be severely damaged and require professional assistance.
• Overheating: If the device feels excessively hot, discontinue use and allow it to cool down. Avoid consecutive jump starts without adequate cooling time.

9. Specifications

10. User Tips

• For optimal performance, ensure the jump starter is fully charged before storing it for long periods.
• Always double-check the polarity when connecting the clamps to your vehicle's battery to avoid damage.
• In cold weather, keep the jump starter in a warmer environment (e.g., inside the car cabin) until ready for use to maximize its efficiency.

11. Warranty & Support

For warranty information, technical support, or service inquiries, please refer to the official 70mai website or contact their customer service directly. Keep your purchase receipt as proof of purchase.

11.1. Product Disposal

As the device contains a lithium battery, please dispose of it responsibly in accordance with local regulations at the end of its service life. Do not dispose of it with general household waste.