NovelLife Vertical Heat Set Insert Tool Pressing Machine Stand

Contents

Vertical Heat Set Insert Tool Pressing Machine Stand Instruction Manual

Model: Vertical Heat Set Insert Tool Pressing Machine Stand

Brand: NovelLife

1. Introduction

This manual provides instructions for the assembly, operation, and maintenance of your NovelLife Vertical Heat Set Insert Tool Pressing Machine Stand. This tool is designed to precisely embed brass knurled nuts into 3D printed parts, enhancing the durability and reusability of your projects. It is compatible with various soldering irons, including TS100, TS101, and 936 models (sold separately).

2. Safety Information

  • Always wear appropriate personal protective equipment (PPE), including safety glasses, when operating the tool.
  • Ensure the soldering iron is properly secured in the clamp before use.
  • Handle hot soldering irons and heat set inserts with extreme caution to prevent burns.
  • Operate the tool in a well-ventilated area to avoid inhaling fumes from heated plastics or solder.
  • Keep the work area clean and free of flammable materials.
  • Disconnect the soldering iron from power when not in use or during maintenance.
  • Keep out of reach of children.

3. Package Contents

Please check the package for the following items:

  • 1x Vertical Heat Set Insert Tool Pressing Machine Stand (assembly required)
  • 1x Set of Heat Set Insert Tips (M2, M3, M4, M5, M6, M8)
  • Necessary assembly hardware (screws, wrenches, etc.)

Note: The soldering iron is not included and must be purchased separately.

4. Specifications

FeatureDetail
DIY Supplies CategoryElectrical
Compatible Soldering Iron Models936, 900M, TS100, TS101 (sold separately)
Working Voltage (for soldering iron)AC110-230V
Power (for soldering iron)60W
Heating Temperature (for soldering iron)180°C-500°C / 356°F-932°F
Stand Size (L*W*H)200x140x260mm / 7.87x5.51x10.24inch
Stroke (Old Version)Max. 140mm / 5.51inch
Stroke (New Version)Max. 210mm / 8.27inch (requires removing top spring)
Max. Clamping Size19mm
Clamping Diameter (for soldering iron handle)17.2mm, 18mm, 19mm
Heat Set Insert Tips ModelsM2, M3, M4, M5, M6, M8
OriginMainland China

Note on Versions: The new version features a wider linear railway and a longer stroke and press handle compared to the old version. The new version's stroke can be extended to 210mm by removing the top spring.

Comparison of Old and New Version of the Heat Set Insert Tool Stand
Figure 1: Comparison of Old and New Version of the Heat Set Insert Tool Stand, highlighting the upgraded wider linear railway and longer stroke/press handle in the new version.

5. Assembly Instructions

The Vertical Heat Set Insert Tool Pressing Machine Stand is provided as an assembly kit. Please follow the steps below to assemble your tool. A video demonstration is also available for visual guidance.

  1. Unpack all components and verify against the package contents list.
  2. Attach the vertical linear rail assembly to the base plate using the provided screws and tools. Ensure it is securely fastened.
  3. Slide the horizontal arm with the soldering iron clamp onto the vertical linear rail.
  4. Adjust the limit knobs on the vertical rail to set the desired pressing depth.
  5. Select the appropriate diameter clamp (17.2mm, 18mm, or 19mm) for your soldering iron handle and install it onto the horizontal arm.
  6. Insert your compatible soldering iron into the clamp and secure it firmly.
  7. Attach the desired heat set insert tip (M2, M3, M4, M5, M6, or M8) to your soldering iron. These tips feature a screw installation design, allowing for easy changing without removing the entire soldering iron tip.
Video 1: Assembly and demonstration of the Heat Set Insert Tool Stand, showing how to set up the stand, attach a soldering iron, and perform an insert.
Assembled Vertical Heat Set Insert Tool Stand
Figure 2: Fully assembled Vertical Heat Set Insert Tool Pressing Machine Stand.
Close-up of the soldering iron clamp with diameter options
Figure 3: Detail of the soldering iron clamp, showing compatibility with 17.2mm, 18mm, and 19mm diameter soldering irons.
Limit knob for stroke control
Figure 4: The limit knob on the vertical rail, used to control the pressing stroke and depth.
Heat set insert tips and adapters
Figure 5: Various heat set insert tips (M2, M2.5, M3, M4, M5, M6, M8) and tip adapters for 936/937/900M and TS100/TS101 soldering irons.

6. Operation Guide

Once assembled and your soldering iron is securely in place with the correct tip, follow these steps for embedding heat set inserts:

  1. Prepare your 3D Printed Part: Ensure the hole for the insert is correctly sized for the chosen brass knurled nut.
  2. Set Soldering Iron Temperature: Turn on your soldering iron and set it to the appropriate temperature for the plastic material of your 3D printed part and the brass insert. A common starting point is around 200-250°C (392-482°F), but this may vary.
  3. Place the Insert: Carefully place a brass knurled nut into the hole of your 3D printed part.
  4. Position the Part: Place the 3D printed part on the base plate of the pressing machine stand, aligning the insert directly under the heat set insert tip.
  5. Adjust Stroke (if necessary): Use the limit knobs on the vertical rail to adjust the maximum depth the soldering iron can travel, ensuring the insert is pressed to the desired depth without damaging the part.
  6. Apply Pressure: Gently lower the horizontal arm, applying steady, even pressure to press the heated insert tip onto the brass nut. The heat will melt the surrounding plastic, allowing the nut to embed smoothly.
  7. Allow to Cool: Once the nut is fully embedded, lift the arm and allow the plastic to cool and solidify around the insert before handling the part.
Soldering iron with heat set insert tip in the stand
Figure 6: A soldering iron with a heat set insert tip installed and ready for operation in the stand.

7. Maintenance

  • Cleaning: Regularly clean the linear rails and moving parts to ensure smooth operation. Use a soft, dry cloth. Avoid abrasive cleaners.
  • Tip Care: Clean heat set insert tips after each use to prevent plastic residue buildup. Allow tips to cool before cleaning.
  • Storage: Store the tool in a dry, clean environment when not in use.
  • Inspection: Periodically check all screws and fasteners for tightness. Tighten if necessary.

8. Troubleshooting

ProblemPossible CauseSolution
Insert not embedding smoothlyIncorrect soldering iron temperature; incorrect hole size; insufficient pressure.Adjust soldering iron temperature; verify hole size for the insert; apply steady, even pressure.
Soldering iron wobbles in clampClamp not tightened sufficiently; incorrect clamp size used.Ensure the clamp is fully tightened; use the correct diameter clamp for your soldering iron.
Arm movement is stiffDust or debris on linear rails; screws too tight.Clean linear rails with a soft cloth; check and slightly loosen screws if they are overtightened.

9. User Tips

  • For best results, practice on scrap 3D printed parts before working on your final project.
  • Experiment with different soldering iron temperatures to find the optimal setting for your specific plastic and insert combination.
  • Ensure the heat set insert tip is clean and free of plastic residue for efficient heat transfer.
  • When embedding, apply pressure slowly and allow the plastic to melt around the insert rather than forcing it.

10. Warranty and Support

For any questions, technical support, or warranty information, please contact the seller or manufacturer directly. A detailed user manual in PDF format may also be available for download from the product page or manufacturer's website.

Reference: User manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.