Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of the EARU EAMPDW-TY-63 WiFi Smart Circuit Earth Leakage Over Under Voltage Protector Relay Device Switch Breaker Energy Power kWh Meter. Please read this manual thoroughly before use to ensure safe and efficient operation.
The EARU EAMPDW-TY-63 is a versatile smart circuit protector designed to safeguard electrical circuits and appliances from various electrical faults, while also providing energy monitoring and smart control features via the Tuya app.
Key Features
- Over Voltage Protection
- Under Voltage Protection
- Current Limit Protection
- Current Leakage Protection
- Temperature Protection
- Energy Monitor (kWh Meter)
- Remote Control via Tuya App
- Voice Control (Amazon Alexa, Google Assistant compatible)
- Time Switch / Scheduling
- Device Sharing
- Voltage Meter, Ammeter
- Memory Function for settings and energy data
Specifications
| Parameter | Value |
|---|---|
| Rated Supply Voltage | AC 220V (AC110/230V) |
| Operation Voltage Range | AC80V-400V (single phase) |
| Rated Frequency | 50/60Hz |
| Electric Current (≥A) Setting Range | 1-63A (adjustable) |
| Overvoltage (>U) Setting Range | 250-300V (adjustable) |
| Undervoltage (<U) Setting Range | 150-190V (adjustable) |
| Electric Leakage Protection | 10-99mA (This feature can be turned off) |
| Error | 1% (Voltage Measurement Accuracy: Not exceeding 1% of the overall range) |
| >U and <U Trip Delay | 0.5s |
| Reset/Start Delay | 5s-90s |
| Rated Insulation Voltage | 400V |
| Output Contact | 1NO |
| Electrical Life | 105 |
| Mechanical Life | 106 |
| Protection Degree | IP20 |
| Pollution Degree | 3 |
| Altitude | ≤2000m |
| Operating Temperature | -30°C to 70°C |
| Humidity | ≤ 50% at 40°C (without condensation) |
| Storage Temperature | -30°C to 70°C |
| Power Display Range | 0-99999.9 kWh |
| Backlight Time | Keep lighting up for 15S without any operation |
| Synchronization Time between App and Device | Max 20s (It depends on the network speed) |
| EU LVD Voltage | Low voltage: Below 50Vac or 75Vdc |
| High-concerned chemical | None |
| Type | Mini Circuit breaker |
| Is Smart Device | Yes |
| Origin | Mainland China |
| Certification | CE |
| App | Tuya |
Product Dimensions

Product dimensions: 85mm (height) x 36mm (width) x 65mm (depth). Other detailed measurements are shown in the diagram.
Installation
WARNING: Installation should only be performed by a qualified electrician. Ensure power is disconnected before installation to prevent electric shock.
The device is designed for 35MM Din Rail installation.
Wiring Diagram

Connect the Neutral (N) and Live (L) wires to the 'IN' terminals at the top and the load to the 'OUT' terminals at the bottom, as indicated in the diagram.
App Setup and Network Connection
The EARU EAMPDW-TY-63 is a smart device compatible with the Tuya Smart or Smart Life app.
1. Download and Install the App
- Scan the QR code below with your mobile QR code scanning tool, or search "Tuya Smart" or "Smart Life" in Google Play Store or Apple App Store to download and install the app.

- Create an account with your mobile number if you don't have one.
2. Connect to Wi-Fi Network
- Ensure your mobile phone is connected to a 2.4 GHz Wi-Fi network. 5 GHz networks are not supported.
- Power on the device. The WiFi indicator light should start flashing.
- Open the Tuya Smart/Smart Life app. On the homepage, click "+" in the upper right corner to enter the device addition page.
- Select "Electrical" -> "Smart Electric Meter" or "Energy" -> "Switch module (Wi-Fi)" (the exact category might vary slightly by app version).
- On the device, press and hold the SET button for 5 seconds until the WiFi indicator blinks rapidly. This puts the device into network connection mode.
- In the app, confirm that the indicator is blinking rapidly and proceed with the connection steps.
- Enter your 2.4 GHz Wi-Fi network password.
- Wait for the device to connect. Once "Added successfully" appears, you can set the installation room of the device.

Visual guide for adding the device to the Tuya Smart app.
Note: If the app fails to add the new device, ensure your Wi-Fi name and password do not contain Chinese characters.
Operation
1. Device Display and Controls

The device features a display showing Overvoltage/Undervoltage, Overcurrent, Leakage Protection, and kWh. Buttons include SET, Increase, Reduce, and ON/OFF. The WiFi indicator shows connection status.
- ON/OFF Button: Controls the power on/off of the device.
- SET Button: Used to view data and enter setup mode.
- Increase/Reduce Buttons: Used to adjust parameter settings in setup mode.
2. Parameter Settings (Manual)
- Click the SET key to view each data point (Voltage, Current, Leakage, kWh).
- Press and hold the SET key for 5 seconds to enter setup mode.
- While in setup mode, press the SET key to cycle through parameters (Over Voltage, Under Voltage, Current Limit, Leakage Protection, Reconnect Times, etc.).
- Use the Increase and Reduce keys to adjust the selected parameter.
- The device will automatically save settings after a short period of inactivity in setup mode.

Visual guide for navigating display data and setting parameters manually.
3. App Control and Advanced Settings
Once connected to the Tuya Smart/Smart Life app, you can access advanced features:
- Remote ON/OFF: Control the device from anywhere.
- Scheduling: Set up time switches, countdowns, or cycle timings for automatic operation.
- Alarm Settings: Configure thresholds for overcurrent, overvoltage, undervoltage, and leakage current alarms.
- Energy Statistics: View daily, monthly, and yearly energy consumption data.
- Temperature Protection: Set the temperature protection range (10-85°C). This parameter is only adjustable via the app.
- Reclosing Settings: Adjust reclosing allowed times and reclose recovery seconds for overcurrent and leakage protection.
- Password Set: Secure your device settings with a password.
Video demonstrating app setup, parameter adjustment, scheduling, and energy monitoring features.

Detailed app interface for energy monitoring, scheduling, and alarm configurations.
4. Energy Consumption Data Clear
To clear the energy consumption data (kWh):
- Press and hold the SET key for 10 seconds until the screen displays "000".
- Use the Increase and Reduce keys to change "000" to "111".
- Press the SET key to save. The energy consumption data will be cleared.
5. Reset to Factory Settings
To reset the device to its factory default settings:
- Press and hold the SET key for 10 seconds until the screen displays "000".
- Use the Increase and Reduce keys to change "000" to "222".
- Press the SET key to save. The device will reset to factory settings.
Maintenance
- Regularly check the device for any physical damage or loose connections.
- Keep the device clean and free from dust and moisture. Use a dry, soft cloth for cleaning.
- Do not use abrasive cleaners or solvents.
- Ensure proper ventilation around the device to prevent overheating.
Troubleshooting
- Device not connecting to Wi-Fi:
- Ensure your Wi-Fi network is 2.4 GHz. 5 GHz networks are not supported.
- Check that the Wi-Fi name and password do not contain special characters, especially Chinese characters.
- Make sure the device is in network connection mode (WiFi indicator blinking rapidly).
- Verify your Wi-Fi password is entered correctly in the app.
- Ensure the device is within range of your Wi-Fi router.
- Device trips frequently due to leakage protection:
- IMPORTANT: If the protector trips three times due to leakage protection, the device will no longer automatically reconnected. This is a safety feature.
- You must manually check the electrical circuit for the cause of the leakage, fix the issue, and then manually reset the device. This ensures user safety.
- Incorrect readings on display:
- Verify that the wiring is correct according to the installation diagram.
- Check the calibration settings in the app if available, or perform a factory reset if necessary.
- Device unresponsive:
- Try power cycling the device (turn off and on).
- If issues persist, perform a factory reset (refer to "Reset to Factory Settings" section).
User Tips
- Utilize the scheduling feature in the Tuya app to automate power control for appliances, saving energy and enhancing convenience.
- Regularly monitor energy consumption through the app to identify power-hungry devices and optimize usage.
- Take advantage of the adjustable protection settings (over/under voltage, overcurrent, leakage) to tailor the device's safety parameters to your specific electrical environment and connected loads.
- For enhanced security, set a password for your device settings within the Tuya app.
Warranty and Support
For technical support, warranty claims, or further inquiries, please contact the manufacturer:
ZHEJIANG EARU ELECTRONICS CO.,LTD
- Address: GUACHUAN ROAD 228 1ST, LIUSHI TOWN, YUEQING CITY, ZHEJIANG PROVINCE, CHINA, 325604
- Website: https://shop28909b0b26794.1688.com/
- Manager: Bob Wu
- Email: 415529869@qq.com
- Phone Number: +86 15821639630
- WeChat ID: totybest-2
A user manual in PDF format is also available for download. Please refer to the product page or contact support for the link.
(Reference: User manual (PDF))