1. Introduction
Dear user, this document provides essential product information and instructions for the use of your CP26 Bluetooth Serial Adapter. Please read carefully before operation.
2. Packing List
The following items are included with your CP26 Bluetooth Serial Adapter, depending on the model purchased:
CP26 Mobile Phone Model (T1)
- DX-CP26 Adapter x1
- Rod Rubber Antenna x1
- USB Data Cable x1
- Instruction Manual x1
- RJ45 Adapter Cable x1
- RS232 Adapter Cable (Male Connector) x1
CP26 Computer Model (T2)
- DX-CP26 Adapter x1
- Rod Rubber Antenna x1
- USB Data Cable x1
- Instruction Manual x1
- RJ45 Adapter Cable x1
- RS232 Adapter Cable (Male Connector) x1
- CP11 Adapter x1
CP26 Device Model (T3)
- DX-CP26 Adapter x2
- Rod Rubber Antenna x2
- USB Data Cable x2
- Instruction Manual x1
- RJ45 Adapter Cable x2
- RS232 Adapter Cable (Male Connector) x2

3. Product Specifications
| Attribute | Specification |
|---|---|
| Brand | PDDAXLQUE |
| Model Number | CP26 |
| Bluetooth Name | RS232/RS485 |
| Bluetooth Version | Bluetooth 5.1 |
| BLE UUIDs | SERVICE UUID: FFE0, NOTIFY/WRITE UUID: FFE1, WRITE UUID: FFE2 |
| Serial Port Type | RS232 |
| Serial Port Default Parameters | 9600bps/8/n/1 (baud rate / data bits / no parity / stop bits) |
| Supported Baud Rates | 2400, 4800, 9600, 19200, 38400, 57600, 115200 |
| Power Supply Method | DC5-36V |
| Power Interface | Type-C |
| Interface Type | RJ45/RS232 Interface |
| Visible Distance (unobstructed) | 420 m |
| Application | IoT, Wireless Data Transmission |
| Certification | CE FCC RoHS |
| CP26 Dimensions | 60mm x 27.8mm x 16.4mm |
| CP11 Dimensions | 67mm x 25mm x 10mm |
| Antenna Length | 108mm |
4. Interface and Function Specifications
CP26 Product Diagram and Indicators

- TX: Data transmission indicator (red)
- RX: Data reception indicator (green)
- WORK: Operational status indicator (blue)
- POWER: Charging indicator (red)
- KEY: Disconnect, switch & baud rate button
- USB: USB power supply port, USB charging port
- ANT: External antenna interface
- RJ45 & RS232: RJ45 communication port, RJ45 to RS232 communication port
Hardware Interface Parameters

5. Setup and Connection
5.1. Install External Antenna
Screw the provided rod rubber antenna onto the ANT connector (7) of the CP26 adapter.
5.2. Connect RS232/RJ45 Adapter Cable
Connect the appropriate adapter cable (RS232 or RJ45) to the communication port (8) of the CP26 adapter. Ensure the connection is secure.
5.3. Software Installation
To enable communication with your devices, you will need to install the relevant software:
- Mobile Version: Search for 'DX-SMART' in your mobile app store (Android/iPhone), then download and install the application.
- Desktop/Bridge Version: For computer use, download the hardware package (serial port software + driver software) from the official website or Google Drive.
Official Website: en.szdx-smart.com
Google Drive Link: drive.google.com/drive/folders/1aepOsN25qKyyDyuhDv8-njDIyJF608SP
GitHub Link: github.com/DX-SMART/WIRELESS-ADAPTER/blob/main/DX-CP26%20Development%20%26%20User%20Information.rar
The product information pack typically contains: Read Me, CH341SER driver, and UartAssist.


6. Operating Modes
The CP26 adapter supports three primary modes of transmission:
- T1: Mobile Phone & CP26 Slave (Transparent Transmission): Enables wireless communication between a mobile phone and a 232 device via the CP26 adapter. Typical transmission distance is 40m.
- T2: CP11 and CP26 Slave (Computer Model): Facilitates wireless communication between a computer (using a CP11 adapter) and a 232 device via the CP26 adapter. Typical transmission distance is 40m.
- T3: CP26 Master & CP26 Slave (Device Model): Allows direct wireless communication between two 232 devices, each equipped with a CP26 adapter (one configured as Master, one as Slave). This mode offers an extended transmission distance of up to 420m.



7. Indicator Lights
The CP26 adapter features several indicator lights to provide status feedback:
- TX Data Indicator (Red/Green): Flashes when the device is transmitting data.
- RX Data Indicator (Green/Blue): Flashes when the device is receiving data.
- WORK Operational Status Indicator (Blue/Red):
- Bluetooth not connected: Blue light flashes. The number of flashes indicates the current baud rate code (see Baud Rate Numbering Table below).
- Bluetooth connected: Blue light is steady on.
- For CP11 adapter, red light flashes when Bluetooth is not connected, indicating baud rate code. Red light is steady on when connected.
- POWER Charging Indicator (Red): Glows red continuously while charging and turns off when fully charged.
8. Baud Rate Adjustment
CP26 KEY Button Functionality
- Power On: Press and hold the KEY button for one second.
- Shutdown: Press and hold the KEY button for three seconds.
- Disconnect Bluetooth: When Bluetooth is connected, press the KEY button once briefly.
- Switch Baud Rate: When Bluetooth is disconnected, press the KEY button twice briefly in quick succession. The number of blue LED flashes (for CP26) or red LED flashes (for CP11) indicates the new baud rate code.
Baud Rate Numbering Table
| Flash Count | 1 | 2 | 3 | 4 | 5 | 6 | 7 |
|---|---|---|---|---|---|---|---|
| Baud Rate | 2400 | 4800 | 9600 | 19200 | 38400 | 57600 | 115200 |
*Factory default baud rate is 9600, indicated by the blue LED flashing three times.
9. Troubleshooting
- Device not connecting to phone/computer:
- Ensure the CP26 adapter is powered on (WORK indicator should be active).
- Verify that the correct 'DX-SMART' app is installed on your mobile device or the CH341SER driver and UartAssist software are correctly installed on your computer.
- Check that the baud rate of the CP26 adapter matches the baud rate of the device you are trying to connect to. Adjust the baud rate using the KEY button as described in Section 8.
- Confirm that Bluetooth is enabled on your phone/computer and the CP26 is discoverable.
- Data transmission issues:
- Check the TX and RX indicator lights for activity. If no lights are flashing, there might be a connection or configuration issue.
- Ensure the physical connections (RS232/RJ45 cables) are secure and correctly wired according to the pinout diagrams.
- Verify that the software settings (e.g., COM port, baud rate, data bits, parity, stop bits) match the CP26's default or configured parameters.
- Power issues:
- Ensure the CP26 adapter is receiving power via the USB port. The POWER charging indicator should glow red when charging.
- If using a CP11 adapter, ensure it is properly plugged into the computer's USB port.
- General communication failure:
- Incorrect connections or incompatible cables can lead to equipment malfunction. Always use the dedicated connection cables supplied and ensure they are correctly inserted.
- If issues persist, refer to the full user manual PDF for more detailed troubleshooting steps.
10. User Tips
- Baud Rate Matching: A common cause of communication failure is mismatched baud rates. Always ensure the CP26's baud rate is set to match your target device. The default is 9600bps.
- Software Compatibility: For computer connections, ensure the CH341SER driver is installed correctly. For mobile, use the official 'DX-SMART' app.
- Optimizing Range: While the device boasts a visible distance of up to 420m in open areas, actual range can vary significantly based on environmental factors (obstacles, interference). For critical applications like topographic equipment, try to minimize obstructions between the adapters.
- Initial Setup: When first setting up, double-check all cable connections and power supply before attempting to establish a Bluetooth link.
11. Warranty and Support
For any queries, technical support, or assistance with your CP26 Bluetooth Serial Adapter, please do not hesitate to contact our support team. We are committed to providing timely assistance.
- Whatsapp: +86 15798463070
- Email: Manager@szdx-smart.com
- Official Website: en.szdx-smart.com
A comprehensive user manual in PDF format is also available for download: