ToolkitRc M8D

Contents

ToolkitRC M8D Smart Charger User Manual

Dual Channel DC 800W*2 30A 1-8S Lithium Battery Fast Charger

Introduction

Thank you for purchasing the M8D balance charger. This manual provides detailed instructions for the safe and efficient operation of your ToolkitRC M8D Smart Charger. Please read this manual carefully before use to ensure proper functionality and to prevent damage to the device or batteries.

The M8D is a touch screen balanced charger product, featuring a total charging power of up to 1600W. It utilizes an IPS bright display with a capacitive touch screen and a roller encoder for convenient operation.

Video: ToolkitRC M8D product overview and feature demonstration.

Safety Warnings

⚠ WARNING: This product can expose you to chemicals including phthalates (DEHP), which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

Please observe the following safety guidelines:

  1. M8D allows an input voltage of DC 10.0V-49.0V. To ensure that the power supply voltage is consistent, pay attention to the positive and negative polarity of the power supply before use.
  2. Do not use this product in hot or humid environments. Keep away from flammable liquids and gases.
  3. Never leave charging batteries unattended.
  4. When not in use, please turn off/unplug the device.
  5. When using the charging function, please set a current that matches the battery performance envelope. Do not set an excessive current for charging to avoid damage to the battery. Check the guidelines of your battery's manufacturer for correct charging instructions.
Safety warnings from the manual

Image: Safety warnings and nomenclature for battery types.

Nomenclature

  • Lipo: Lithium polymer battery, nominal voltage 3.70V, 4.20V when fully charged.
  • LiHV: High-voltage lithium battery, nominal voltage 3.85V, 4.35V when fully charged.
  • LiFe: Lithium iron battery, nominal voltage 3.30V, 3.60V when fully charged.
  • Lion: Lithium-ion battery, nominal voltage 3.60V, 4.10V when fully charged.
  • LTO: Lithium-ion battery, nominal voltage 2.40V, fully charged 2.70V.
  • NiMh: Nickel-hydrogen battery, nominal voltage 1.20V.
  • PB: Lead-acid battery, nominal voltage 2.00V.

Package Contents

The ToolkitRC M8D Smart Charger package includes the following items:

  • M8D Charger x 1
  • USB-C Cable x 1
  • XT90 Input Cable x 1
  • Manual x 1
  • Screen Protector x 1
ToolkitRC M8D package contents

Image: Contents of the M8D charger box, including the charger, cables, manual, and screen protector.

M8D Layout

Familiarize yourself with the different parts of your M8D charger:

M8D Charger Layout Diagram

Image: Front and back views of the M8D charger with labels for Display/Touch panel, CH/Exit button, Main port*2, Balance port*2, Scroll wheel, DC input XT90, USB A/C output, and Cooling fan.

Front:

  • Display/Touch panel: Main interface for interaction.
  • CH/Exit: Button for channel selection or exiting menus.
  • Main port*2: Primary battery connection ports.
  • Balance port*2: Ports for balancing battery cells.
  • Scroll wheel: For navigation and value adjustment.

Back:

  • DC input XT90: Power input port (DC 10-49V).
  • USB A/C output: USB charging ports.
  • Cooling fan: For heat dissipation.

Setup and Quick Start

Follow these steps to set up and begin using your M8D charger:

  1. Connect the device to a DC 10-49V power source using the XT90 input cable.
  2. The screen will show the boot logo for 2 seconds.
  3. An audible tone will accompany the boot sequence.
  4. After booting up, the screen enters the main interface.
  5. Touch the main interface or scroll the [Scroll Wheel] to select the desired function, then press [Scroll Wheel] to confirm.
  6. Touch the [Settings icon Settings icon] or press and hold [Scroll Wheel] for 2 seconds to enter the system settings interface.
  7. Touch the [Info] button or scroll the [Scroll Wheel] to select the [Info] button to display the voltage and internal resistance in the corresponding channel.
  8. Touch [Status], short press [Scroll Wheel] to select [Status], or touch [Status] to select the charging task when the channel is idle. You can adjust and end the work while the channel is working.
  9. Press the [Exit Button] to end the modification or return to the previous interface.
Quick Start Guide for M8D Charger

Image: Visual guide for quick start steps, showing the main interface and interaction points.

System Settings

To access system settings, select the [Settings icon] on the main interface, or press and hold the scroll wheel for 2 seconds when both channels are idle. This allows you to configure various parameters.

M8D System Settings Interface

Image: System settings interface showing Input Settings, Security Settings, and Charge Settings.

Input Settings

Enter the relevant settings of the power supply:

  • Input power: P1, P2, and P3 can be saved and selected. Users can set the power, current, voltage, and other information of the input power supply.
  • Power Type: The type of input power supply for the current value. The discharge function can be selected as recycling Only when the input was set to battery.
  • Power Selection: When this setting is turned on, each time the charger powers on, it prompts you to select a power number.
  • Max power: The maximum power absorbed from the input port when charging.
  • Max current: The maximum current drawn from the input port during charging.
  • Min voltage: The lowest allowable input voltage.

Charging Safety Settings

Work-related security settings:

  • Safe Inter Temp.: Above this temperature value, the device will stop the main port output.
  • Safe time: The maximum time of continuous charging; it will stop charging if it exceeds this.
  • Safe capacity: The maximum capacity for continuous charging, and it will stop charging if exceeded.
  • Synchronous mode: After turning on this function, the two channels can be combined with the main port to charge the same battery, and the maximum current can reach 50A.
  • Continuous Operation: After turning on the function, remove the fully charged battery, and after connecting the next battery, it will automatically start charging according to the previous charging setting as the last battery.

System Settings (General)

  • Backlight: The backlight brightness level of the display can be set from 1 to 10.
  • Sound Volume: The speaker announces the volume, which can be set to high, medium, low, and off.
  • Language: System display language can be changed (supports 11 languages).
  • Theme style: Two styles of Light and Dark can be selected.
  • SD-log: Logging interval settings.
  • ID: The unique ID of the device factory settings.

Operating Instructions

Charging Settings

In the main interface, select and short press [Scroll Wheel] to enter the charging function. If "Battery selection" is turned on in the main setting interface, 10 battery records can be saved, and the following interface is displayed. Otherwise, it will default to the first battery record, skipping this step.

M8D Battery Selection Interface

Image: Battery selection interface showing saved battery profiles.

1. Battery Type

Select the battery that has been set, or press [New Battery], select the battery number to enter the new battery setting interface. The charger supports charging 7 kinds of batteries: LiPo, LiHv, LiFe, Lion, LTO, NiMH, and PB. After selecting the battery that matches the actual battery, press [Confirm] to take effect and rewind to the previous page.

M8D Battery Type Selection

Image: Battery setting interface with a dropdown for selecting battery type (LiPo, LiHv, LiFe, Lion).

2. Number of Cells

Move the cursor to the position of "Battery Cells", short press [Scroll Wheel] to modify the number of battery cells. When set to [Auto], the charger will automatically identify the number of strings of connected batteries based on the voltage of the battery connected to the output port. Press [Confirm] to take effect and go back to the previous page.

M8D Number of Cells Setting

Image: Battery setting interface with a dropdown for selecting the number of battery cells (Auto, 1S, 2S, 3S).

Tips:

  • Accessing the battery over-discharge or overcharge may lead to a battery string number identification error. You need to manually set the correct number of strings.
  • Incorrectly setting the number of strings may damage the batteries or charger. Please be careful with the settings.
  • Lixx batteries can be identified more accurately when they are connected to the balance port.

3. Mode

Modify the work Mode:

M8D Mode Selection Interface

Image: Battery setting interface with a dropdown for selecting the operation mode (Charge, Discharge, Cycle, Destroy).

LiPo, LiHV, LiFe, and Lion batteries can be selected for charging and storage. NiMh and PB batteries can be selected for charging. Press [Confirm] to take effect and go back to the previous screen interface.

4. End Voltage Setting (TVC)

Move the cursor to [End Voltage] to modify the end voltage of the monolithic battery. When the working mode is charging, it is the charging cut-off voltage. The range is ±50mV of full voltage. When the working mode is discharging, it is the discharging cut-off voltage. Select the voltage adjustment value, step increment of 0.01V.

M8D End Voltage Setting

Image: Battery setting interface showing end voltage options (4.20V, 4.21V, 4.22V, 4.23V).

Tips:

  • Only LiPo, LiHV, LiFe batteries can set the cut-off voltage.
  • Do not modify the cut-off voltage if you are not familiar with the battery characteristics.
  • The charging cut-off voltage can be set to a range of ±50mV of full voltage.
  • TVC: Abbreviation for Terminal Voltage Control.

5. Charging Current

Move the cursor to the [Charging Current] position, and slide the [Slider] to modify the current. Or scroll the [Scroll Wheel] to adjust the value in 0.1A steps. Scroll quickly [scroll wheel] to add or decrease faster. The charger supports up to 30A.

M8D Charging Current Adjustment

Image: Battery setting interface showing charging current adjustment slider.

Tips:

  • Please set the charging rate of 1-2C according to the battery capacity. For example, if the battery capacity is 2000mAh, please set the charging current to 2.0-4.0A. Check the guidelines of your battery's manufacturer for correct charging instructions.

6. NiMh Setting (PeakV)

When the battery type is NiMh, the PeakV value can be set, and the setting range is 3mV-15mV.

M8D NiMh PeakV Setting

Image: Battery setting interface with a dropdown for selecting NiMh PeakV values (e.g., 5mV, 6mV, 7mV, 8mV, 9mV).

Tips:

  • Only NiMh battery can set the battery negative pressure value.
  • PeakV: When the NiMH battery is fully charged, the voltage drop peak value of each cell.

Charging Process Display

When charging starts, the charger enters the working interface:

M8D Charging Interface Display

Image: Main charging interface showing real-time charging data for two channels.

Select the [Info] button on this interface to view the voltage value of the corresponding channel, slide the voltage information to the left, and switch to the internal resistance display.

M8D Charging Adjustment and Info Display

Image: Charging adjustment screen and detailed display content description.

Display content description:

  • 24.0V: Input supply voltage.
  • 14.8A: Input supply current.
  • 20.0Wh: The cumulative power consumption of the input power supply.
  • 45°C: The internal temperature of the charger.
  • 32.23V: The voltage of the main port of the first channel.
  • 5.00A: The current of the main port of the first channel.
  • 10:59: First channel working hours.
  • 2000mAh: The cumulative capacity of the first channel.
  • 4.200V: The first battery voltage.
  • 4.200V: The fourth battery voltage (Red mark means this battery is under balance management).
  • ---V: No battery connected.

Battery Destruction Function

When a lithium battery needs to be disposed of, the destruction function can be used to completely drain the battery's voltage. This prevents the risk of combustion due to residual voltage after discarding.

M8D Battery Destruction Function Interface

Image: Battery setting interface showing the 'Destroy' mode for safe battery disposal.

⚠ Warning: The battery in normal use cannot use this function, and the battery can be emptied by using the destroy function, causing irreversible damage.

Maintenance

Firmware Upgrade

After connecting the M8D to the computer with the USB data cable in the box, the computer will recognize a USB drive named Toolkit. Download the upgrade file `app.upga` from the official website. Copy and paste the new file and overwrite the files in the USB drive to upgrade the firmware.

Fan Stepless Speed Regulation

When the internal temperature of the device exceeds 43°C, the fan will increase its speed linearly according to the internal temperature increase or power increase. This makes it less noisy when operating at low temperatures or low power.

M8D Dual Fans Illustration

Image: Illustration of the M8D's dual fans with infinitely adjustable speed for efficient and quiet cooling.

Manually Calibrate Voltage

In the system settings, you can access the manual voltage calibration function. Use a voltmeter to measure the actual voltage of each battery, move the cursor to the corresponding voltage value, and modify the voltage value to be consistent with the voltmeter reading to achieve calibration. After the calibration is completed, move the cursor to save, and the save is successful. Just exit or shut down.

TF Card Logging

The M8D features a built-in 256M TF card for full support of charging and discharging data storage and analysis. This allows users to log and review performance data.

M8D TF Card Logging Feature

Image: Diagram showing the TF card slot and data logging capabilities for VOUT and IOUT.

USB Fast Charging

M8D has a built-in USB fast charging protocol, with a C port supporting up to 65W charging power. Supported protocols include PD, QC, AFC, FCP, SCP, PE, SFCP, VOC.

M8D 65W Fast Charging

Image: M8D charger providing 65W fast charging to a smartphone.

Fully Charged Replenishment

When the lithium battery is charged, it prompts "Fast charging has ended". If the battery is not removed, it will automatically be charged at a constant voltage trickle to bring the battery to a fuller state.

Troubleshooting

Here are some common issues and their solutions:

  1. Device functionality error: If there is an error, download a new program from the official product website and upgrade it. After the upgrade, restore factory settings for normal operation.
  2. Sudden shutdown and restart during charging: Check if your power adapter's power is below the charging requirements. It is recommended to reduce the charging speed.
  3. Repeated restarts after power-on: There might be dust in the TF memory card slot. Remove the TF memory card, wipe it clean, and reinsert it to restore normal operation.
  4. Slow discharge speed: The discharge speed is a fixed interval speed and cannot perform rapid discharge.
  5. Long-term high-speed charging: Not allowed. After high-speed charging, a battery needs to be cooled before use, otherwise it will burn out.
  6. Cannot enter settings page during charging: You need to stop charging before entering the settings page.
  7. Charger burned out in parallel charging mode: The parallel charging mode must be learned to use first. If the wrong wire is connected or the parallel charging mode is used incorrectly, the charger will be burned out.
  8. Cannot fast charge: Only batteries with high discharge rates can be charged quickly. If the battery has a slow discharge rate, it cannot be charged quickly, otherwise it will damage the battery or charger.
  9. Functions not working after firmware upgrade: If some functions still cannot be used normally after upgrading to the latest firmware, you can send a video of the malfunction to the brand's email. The brand will create new firmware to address the vulnerability. This is not considered a quality issue.

Specifications

Detailed specifications for the ToolkitRC M8D Smart Charger:

M8D Charger Specifications Table

Image: Table detailing general and charger specifications.

Attribute Value
Brand Name ToolKitRc
Model Number M8D
Quantity 1 pcs
Use Vehicles & Remote Control Toys
Material Plastic
Is Electric No Battery
Is it battery/power supply N
Is it charger/adapter Y
High-concerned chemical None
Plastic Type PC
Remote Control Peripherals/Devices Battery Charging Units
Origin Mainland China
Recommend Age 14+y
Certification CE, FCC, RoHS
Is Batteries Included No

General Specifications

  • Product size: 130.0mm * 97.0mm * 42.0mm
  • Product weight: 450g
  • Packing size: 140.0mm * 110.0mm * 50.0mm
  • Packaging weight: 700g
  • LCD: IPS 3.5 inch 320*480 pixel
  • Touch panel: Capacitive

Charger Specifications

  • Input voltage: 10-49V @ MAX 60A
  • Battery type: LiPo, LiHV, LiFe, Lion LTO @ 1-8S; NiMh @ 1-20S; Pb @ 1-15S
  • Balance current: 2000mA @ 4.2V
  • Charging power: 800W @ MAX 30A*2 (Asynchronous mode); 1600W @ MAX 50A (Synchronous mode)
  • Discharging power: 800W @ MAX 30A*2 Recycle mode; 40W @ 10A Normal mode
  • USB-C output: 65W @ 5.0-20.0V or Upgrade (Tip: when input under 10-36V, the 65W USB-C output is available)
M8D Charger Dimensions

Image: Dimensions of the M8D charger (130.0mm x 97.0mm x 42.0mm).

User Tips

  • For optimal performance, ensure your power adapter meets or exceeds the charger's input requirements, especially when charging at higher speeds.
  • Regularly check the TF memory card slot for dust to prevent unexpected restarts.
  • Always verify battery cell count and type settings before initiating a charge to avoid battery damage.
  • Take advantage of the data logging feature to monitor battery performance and charging cycles over time.
  • When using the battery destruction function, confirm the battery is intended for disposal as this process is irreversible.

Warranty and Support

For warranty information, technical support, or to report issues not covered in this manual, please refer to the official ToolkitRC website or contact their customer service directly. Keep your purchase receipt as proof of purchase for any warranty claims.

Further information, news, and firmware updates for your charger can be found on the official ToolkitRC website.


Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.