NEXTORCH myTorch S AA

Contents

NEXTORCH myTorch S AA Smart Flashlight Instruction Manual

Third Generation Smart Flashlight with Programmable Modes

1. Introduction

The NEXTORCH myTorch S AA is a third-generation smart flashlight designed for versatility and performance. Featuring a U.S. CREE® LED, it delivers up to 130 lumens of brightness. Its intelligent USB direct charging design allows for convenient recharging of compatible batteries, and its patented Smart Torch Technology (STT) enables extensive customization of lighting modes via computer software.

NEXTORCH myTorch S AA Smart Flashlight with key features listed
The myTorch S AA, highlighting its intelligent USB direct charge, S.O.S. distress mode, intelligent dimming, IPX7 waterproof rating, 1m fall protection, and PC connectivity.

2. Package Contents

Please check the package to ensure all items are present:

  • 1 x myTorch S AA Flashlight
  • 1 x AA Alkaline Battery
  • 1 x Hand Strap
  • 2 x Seal Rings
  • 1 x Micro USB Cable
  • 1 x AA Coil
  • 1 x Flashlight Sleeve
Contents of the NEXTORCH myTorch S AA package including flashlight, holster, USB cable, and manual
The myTorch S AA flashlight and its included accessories.

3. Setup

3.1 Battery Installation

  1. Unscrew the tail cap of the flashlight.
  2. Insert one AA battery (alkaline or Ni-MH rechargeable) with the positive (+) end facing towards the head of the flashlight.
  3. Screw the tail cap back on securely.

3.2 Charging

The myTorch S AA features an intelligent USB direct charging design. It automatically identifies whether the inserted battery can be recharged or not. Only Ni-MH AA batteries are rechargeable via the flashlight's USB port. Alkaline batteries can be used as a backup power source but cannot be recharged within the flashlight.

  • Connect the Micro USB cable to the flashlight's charging port.
  • Connect the other end of the USB cable to a power source (e.g., computer USB port, wall adapter, car charger, power bank).
  • The LED charge indicator will show a red light during charging.
  • When charging is complete, the LED charge indicator will turn yellow-green.
NEXTORCH myTorch S AA flashlight connected to a USB cable for charging
The myTorch S AA connected via USB for charging.
LED Charge Indicator showing red for charging and yellow-green for complete
LED Charge Indicator status: Red for charging, Yellow-green for complete.
Diagram showing battery compatibility: Do not use 3.7V 14500 AA battery, compatible with Alkaline and Ni-MH AA batteries
Important battery compatibility: Do not use 3.7V 14500 AA batteries. Only Ni-MH AA batteries are rechargeable via USB.
Various convenient charging options for the myTorch S AA, including laptop USB, wall adapter, car charger, and power bank
Multiple convenient charging options are available for the myTorch S AA when using rechargeable Ni-MH AA batteries.

4. Operating Instructions

4.1 Basic Operation

The myTorch S AA typically operates with a single tail switch for basic functions. Press the switch to turn the flashlight ON/OFF and cycle through pre-set modes (High, Medium, Low, Strobe).

4.2 Smart Torch Technology (STT) & NEXTUNER 3.0

The myTorch S AA features Smart Torch Technology (STT), allowing you to customize its lighting modes to your exact needs using the NEXTUNER 3.0 software. This software can be downloaded from the NEXTORCH website.

  1. Connect your myTorch S AA to a computer using the Micro USB cable.
  2. Launch the NEXTUNER 3.0 software.
  3. Within the software, you can:
    • Adjust the flashlight's brightness and flashing modes.
    • Set flashlight modes and their order of access.
    • Quickly access military, police, tactical, or wilderness modes to match your environment.
    • Access S.O.S. rescue mode.
    • Choose from pre-set Morse Code signals or create your own.
    • Add or delete flashlight modes.
    • Display the flashlight's current settings.
    • Save and share your individual flashlight mode settings.
  4. You can also import pre-configured application mode groups (e.g., military, tactical, outdoor) with a single click.
Laptop displaying NEXTUNER software connected to a NEXTORCH myTorch S AA flashlight
Customize your myTorch S AA with the NEXTUNER 3.0 software.
NEXTUNER 3.0 software interface for customizing flashlight modes
The NEXTUNER 3.0 software allows users to individualize lighting modes.

4.3 Smart Memory Mode

The flashlight features a Smart Memory Mode that remembers your last used lighting preference. To activate or resume a preferred mode setting:

  • Press and hold the switch for 5 seconds or more to save the current mode.
  • Turn the flashlight OFF.
  • Press and hold the switch again to resume the previously saved mode setting.
NEXTORCH myTorch S AA with text 'Smart Memory Mode remembers your lighting preference'
The Smart Memory Mode feature for personalized lighting preferences.

5. Maintenance

  • Cleaning: Regularly clean the flashlight body with a soft, damp cloth. Avoid using harsh chemicals or abrasive materials.
  • Battery Care: If the flashlight will not be used for an extended period, remove the battery to prevent leakage. Ensure only compatible batteries (Alkaline or Ni-MH AA) are used. Do NOT use 3.7V 14500 AA batteries.
  • O-rings: Periodically inspect the O-rings for wear and tear. Replace them if damaged to maintain the flashlight's waterproof rating. A spare set of O-rings is included.

6. Troubleshooting

  • Flashlight not turning on: Check if the battery is inserted correctly with the correct polarity. Ensure the tail cap is screwed on tightly. Verify the battery has sufficient charge.
  • Dim or flickering light: The battery may be low. Recharge Ni-MH batteries or replace alkaline batteries. Ensure battery contacts are clean.
  • Charging issue: Ensure the USB cable is properly connected to both the flashlight and the power source. Check the LED indicator for charging status. If using a Ni-MH battery, ensure it is not fully discharged to a point where it cannot be detected by the intelligent charging circuit.
  • Customization issues with NEXTUNER: Ensure the flashlight is properly connected to the computer and the NEXTUNER software is running. Check for software updates if problems persist.

7. Specifications

The NEXTORCH myTorch S AA is tested in strict accordance with ANSI/NEMA FL1 standards.

Table of ANSI/NEMA FL1 standards for myTorch S AA, showing light output, run time, beam distance, impact resistance, waterproof rating, and accessories.
Performance specifications based on ANSI/NEMA FL1 standards.
General Specifications
AttributeValue
Brand NameNEXTORCH
Model NumbermyTorch S AA
Light SourceCREE XP G2 LEDs
Max Output130 Lumens
Switch ModeHigh/Middle/Low
Battery Type1 * AA alkaline batteries (standard) / 1 * AA nickel-metal hydride batteries
ChargingRechargeable (Ni-MH only), Direct charging
Lighting Distance81m (265.75 ft)
Waterproof RatingIPX7, 1 meter
Drop Height Resistance1 meter
Body Materialaerospace grade reinforced aluminium 6061-T6
Surface Treatmenthard anodised
Size120mm (length) x 19.2mm (body diameter) x 26.4mm (head diameter)
Weight56g (without battery)
FunctionShock Resistant, Self Defense
CertificationCE, ROHS
NEXTORCH myTorch S AA flashlight submerged in water, demonstrating IPX-7 waterproof standard up to 1m
The myTorch S AA is IPX-7 waterproof, submersible up to 1 meter.
Close-up of the NEXTORCH myTorch S AA showing brick etching and anti-roll design
The brick etching and anti-roll design prevents the flashlight from rolling away on uneven surfaces.

8. User Tips

  • Optimal Performance: For best performance and to utilize the USB charging feature, use high-quality Ni-MH rechargeable AA batteries.
  • Customization: Take advantage of the NEXTUNER 3.0 software to tailor the flashlight's modes to your specific activities, whether it's for outdoor adventures, tactical use, or daily tasks.
  • Portability: Use the included hand strap or flashlight sleeve for convenient and secure carrying during various activities.
  • Emergency Use: Familiarize yourself with the S.O.S. distress mode for emergency situations.
Two images showing portable ways to carry the myTorch S AA: with a wrist strap and in a belt holster
Various portable carrying options for the myTorch S AA.

9. Warranty & Support

NEXTORCH products are covered by a 5-year warranty. For any questions or support regarding your product, please contact NEXTORCH customer service.

You can find more information and download the NEXTUNER 3.0 software at the official NEXTORCH website: www.nextorch.com

10. Product Video Overview

An overview of the NEXTORCH myTorch S Smart Torch, demonstrating its features, brightness levels, STT infinite modes, and various charging options.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.