DEKO WD01

Contents

DEKO WD01 Non-Contact Laser IR Infrared Digital Thermometer User Manual

Model: WD01 | Brand: DEKO

1. Introduction

The DEKO WD01 Non-Contact Laser IR Infrared Digital Thermometer is designed for safely measuring surface temperatures from a distance. It provides accurate readings without the need for direct contact, making it ideal for various applications including hot water pipes, engine parts, cooking surfaces, hot tubes, insulation, and electrical connections.

This manual provides essential information for the safe and effective use of your DEKO WD01 thermometer. Please read it thoroughly before operation and keep it for future reference.

2. Safety Information

2.1 General Safety Warnings

  • CAUTION: LASER RADIATION. DO NOT STARE INTO BEAM.
  • Do not point the laser directly at eyes or indirectly off reflective surfaces.
  • Keep the device out of reach of children.
  • Do not use the thermometer for medical purposes or to measure body temperature. This device is designed for industrial and household surface temperature measurements.
  • Do not use the device in environments with explosive gas, steam, or dust.
  • Avoid exposing the device to extreme temperatures, humidity, or direct sunlight for prolonged periods.

3. Product Overview

The DEKO WD01 thermometer features a user-friendly design with an LCD display and intuitive controls.

Detailed view of the DEKO WD01 infrared thermometer, highlighting components like the laser, thermometer probe, trigger, battery cover, LCD, backlight button, C/F button, and laser button.

Figure 1: DEKO WD01 Infrared Thermometer Components

3.1 Components and Controls

  1. IR Sensor/Thermometer Probe: Detects infrared radiation to measure temperature.
  2. Laser Aperture: Emits a laser dot for precise targeting.
  3. LCD Display: Shows temperature readings, emissivity, and other indicators.
  4. Trigger: Press and hold to take live readings; release to hold the last reading.
  5. Battery Cover: Located on the handle for battery access.
  6. Buttons:
    • C/F Button: Toggles between Celsius (°C) and Fahrenheit (°F) temperature units.
    • Backlight Button: Turns the LCD backlight ON/OFF.
    • Laser Button: Turns the laser pointer ON/OFF.

4. Setup

4.1 Battery Installation

The DEKO WD01 thermometer requires two (2) AAA batteries (not included).

  1. Locate the battery cover on the handle of the device.
  2. Gently slide or open the battery cover.
  3. Insert two AAA batteries, ensuring correct polarity (+/-).
  4. Close the battery cover securely.
Image showing the battery compartment of the DEKO WD01 infrared thermometer, indicating where to insert 2 AAA batteries (not included).

Figure 2: Battery Installation

5. Operating Instructions

5.1 Taking a Measurement

  1. Point the thermometer at the target surface.
  2. Press and hold the trigger to activate the device and begin taking live temperature readings. The laser pointer can be activated to help aim.
  3. The temperature will be displayed on the LCD screen.
  4. Release the trigger to hold the last measured temperature on the display for easy recording.
Hands holding DEKO WD01 thermometer, showing how to hold the trigger for live readings and release for locked results. Includes a caution for laser radiation.

Figure 3: Hold, Scan & Look Functionality

5.2 Unit Selection (°C/°F)

Press the 'C/F' button to switch between Celsius and Fahrenheit temperature units.5.3 Backlight and Laser Pointer

Use the dedicated Backlight and Laser buttons to turn these features ON or OFF as needed.

5.4 Emissivity Adjustment

The DEKO WD01 features adjustable emissivity (from 0.10 to 1.0) to ensure precise temperature measurements on various surfaces. Different materials emit infrared energy differently, and adjusting the emissivity setting helps compensate for this.

DEKO WD01 thermometer measuring oil with emissivity 0.94 and ice with emissivity 0.98, demonstrating adjustable emissivity.

Figure 4: Emissivity Examples for Different Surfaces

Close-up of the DEKO WD01 thermometer display showing emissivity adjustment for steel (0.80) and iron (0.70).

Figure 5: Emissivity Adjustment on Display

To adjust emissivity:

  1. With the device ON, press the 'MODE' button (if available, or the button typically used for settings) to enter emissivity adjustment mode.
  2. Use the Up/Down buttons (often shared with C/F or Backlight) to change the emissivity value.
  3. Refer to a standard emissivity table for common materials to set the appropriate value for your target surface.

5.5 Distance to Spot Size (D:S)

The DEKO WD01 has a Distance to Spot (D:S) ratio of 12:1. This means that at a distance of 12 units from the target, the measurement spot diameter will be 1 unit. For example, if you are 12 inches away from the target, the measurement spot will be 1 inch in diameter. Ensure the target is larger than the spot size for accurate readings.

Diagram illustrating the Distance to Spot (D:S) ratio of 12:1 for the DEKO WD01 infrared thermometer, showing measurement spot sizes at various distances.

Figure 6: Distance to Spot Ratio Diagram

5.6 Auto Power Shut Off

The device will automatically power off after 7 seconds of inactivity to conserve battery life.

6. Maintenance

6.1 Cleaning

  • Clean the lens with a soft, clean cloth or cotton swab.
  • Clean the thermometer casing with a damp sponge or soft cloth and mild soap.
  • Do not use abrasive cleaners, solvents, or immerse the device in water.

6.2 Storage

  • Store the thermometer in a cool, dry place away from direct sunlight and extreme temperatures.
  • Remove the batteries if the device will not be used for an extended period to prevent battery leakage.

7. Troubleshooting

ProblemPossible CauseSolution
Display shows "LO" or "HI"Temperature is outside the measurement range.Ensure the target temperature is within -50°C to 400°C (-58°F to 752°F).
Blank displayLow or dead batteries.Replace with fresh AAA batteries.
Inaccurate readingsIncorrect emissivity setting; target too small or too far.Adjust emissivity for the target material. Ensure the target is larger than the measurement spot and within the D:S ratio.
Laser not workingLaser feature is turned off.Press the Laser button to turn it ON.

8. Specifications

FeatureSpecification
TheoryInfrared Thermometer
Measuring Range-50°C ~ 400°C (-58°F ~ 752°F)
Max Measuring Temperature120°C & Above
Accuracy±1.5% of reading or ±1.5°C (±3°F)
Temperature Resolution0.1°C or 0.1°F
Repeatability1% of reading or 1°C
Response Time500mSec (95% response)
Spectral Response8-14 µm
EmissivityAdjustable from 0.10 to 1.0 (0.95 Preset)
Distance to Spot Size (D:S)12:1
Operating Humidity10~90% RH non-condensing (up to 30°C)
Storage Temperature-20°C ~ 60°C
Power TypeAAA Battery (2x 1.5V, not included)
Typical Battery Life12 hours
Display TypeDIGITAL
Display Size1.9 Inches & Under
Product Dimension140 x 85 x 35mm (L*W*H)

9. User Tips

  • Not for Body Temperature: This infrared thermometer is designed for measuring surface temperatures of objects and is not intended for medical use or measuring human body temperature. For accurate body temperature readings, use a clinical thermometer.
  • Consider Emissivity: Always adjust the emissivity setting to match the material you are measuring for the most accurate results. Highly reflective surfaces may require specific emissivity settings or a non-reflective coating for measurement.
  • Maintain Distance: Keep the Distance to Spot (D:S) ratio in mind. Ensure the target area is larger than the measurement spot to avoid inaccurate readings from surrounding areas.

10. Warranty and Support

For any questions, technical support, or warranty claims, please contact the DEKO Official Store or the retailer from whom you purchased the product. Please retain your proof of purchase for warranty purposes.

11. Video Demonstration

Watch this video for a visual guide on how to use your DEKO WD01 Infrared Thermometer:

Video: Demonstrating the features and use of the DEKO WD01 infrared thermometer, including temperature measurement and emissivity adjustment.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.