LM317 Adjustable Regulated Power Supply Kit LM317 Adjustable Regulated Power Supply Kit

Contents

LM317 Adjustable Regulated Power Supply Kit

Continuous Adjustable DC Power Supply DIY Teaching Training Parts

1. Introduction

This manual provides detailed instructions for assembling, operating, and maintaining your LM317 Adjustable Regulated Power Supply Kit. This kit is designed for educational purposes and hobbyists, allowing you to build a stable DC power supply with continuously adjustable output voltage.

The LM317 is a versatile three-terminal adjustable positive voltage regulator capable of providing over 1.5A of output current with an output voltage range of 1.25V to 37V (depending on input voltage). It features built-in overload protection and safe operating area protection.

2. Package Contents

Please verify that all components listed below are included in your kit:

LM317 Kit Components

Image: All components included in the LM317 Adjustable Regulated Power Supply Kit.

ComponentDescriptionSpecificationQuantity
D1-D6Rectifier Diodes1N40076
P1, P2Terminal BlocksKF301-2P2
R1Resistor240Ω1
R2Resistor1KΩ1
C1Electrolytic Capacitor1000uF1
C2Electrolytic Capacitor470uF1
C3, C4Ceramic Capacitors104 (0.1uF)2
LED1Red LED5MM1
RP1Potentiometer10K1
VR1Integrated CircuitLM3171
Heat SinkHeat SinkFor VR11
ScrewMounting ScrewFor Heat Sink1
PCBPrinted Circuit BoardLK129071

3. Specifications

ParameterValue
Input Voltage (AC)1.5V - 15V AC
Input Voltage (DC)3V - 20V DC
Output Voltage1.25V - 12V (continuously adjustable)
Output CurrentUp to 1A (max 1.5A for LM317 chip, but kit components limit to 1A)
Operating Temperature-55 °C to +150 °C
PCB Dimensions (L x W)59.5mm x 31.5mm
ApplicationSpeaker, Voltage Regulator, DIY Teaching Training
PCB Dimensions

Image: Printed Circuit Board (PCB) dimensions.

4. Setup and Assembly Instructions

This kit requires soldering. Basic soldering skills and tools (soldering iron, solder, wire cutters) are necessary. Pay attention to component polarity where indicated.

Circuit Diagram and PCB Layout

Image: Circuit diagram and component placement guide on the PCB.

  1. Prepare PCB: Ensure the PCB is clean and free of any debris.
  2. Solder Diodes (D1-D6): Solder the six 1N4007 rectifier diodes. Pay close attention to the polarity: the silver band on the diode must match the band marking on the PCB.
  3. Solder Resistors (R1, R2): Solder the 240Ω (R1) and 1KΩ (R2) resistors. Resistors are non-polarized.
  4. Solder Ceramic Capacitors (C3, C4): Solder the two 104 (0.1uF) ceramic capacitors. These are non-polarized.
  5. Solder Electrolytic Capacitors (C1, C2): Solder the 1000uF (C1) and 470uF (C2) electrolytic capacitors. These are polarized. The longer lead is positive (+), and the shorter lead (or the side with a stripe) is negative (-). Match these to the markings on the PCB.
  6. Solder LED (LED1): Solder the 5MM Red LED. The longer lead is positive (+), and the shorter lead is negative (-). Match these to the markings on the PCB.
  7. Solder Potentiometer (RP1): Solder the 10K potentiometer. Ensure it sits flush against the PCB.
  8. Mount LM317 (VR1) with Heat Sink: Attach the heat sink to the LM317 (VR1) using the provided screw. Then, solder the LM317 to the PCB, ensuring the metal tab faces the heat sink and aligns with the PCB footprint.
  9. Solder Terminal Blocks (P1, P2): Solder the two KF301-2P terminal blocks. P1 is for input (AC6-32V or DC9-36V) and P2 is for output.
  10. Inspect Solder Joints: Carefully inspect all solder joints for shorts, cold joints, or poor connections. Ensure all components are correctly oriented.
Assembled Board FrontAssembled Board Rear

Image: Front and rear views of the assembled power supply board.

5. Operating Instructions

  1. Connect Input Power: Connect your AC (6-32V) or DC (9-36V) power source to the input terminal block (P1). Ensure correct polarity for DC input (usually marked on the PCB).
  2. Verify Power On: Once input power is connected, the red LED (LED1) should illuminate, indicating the circuit is powered.
  3. Adjust Output Voltage: Use a small screwdriver or your fingers to turn the knob of the potentiometer (RP1). Turning it clockwise will increase the output voltage, and counter-clockwise will decrease it.
  4. Measure Output Voltage: It is highly recommended to use a multimeter to measure the output voltage at the output terminal block (P2) before connecting any load, especially sensitive electronics.
  5. Connect Load: Once the desired voltage is set and verified, connect your device or circuit to the output terminal block (P2). Ensure correct polarity.

Video: Demonstration of adjusting the output voltage using the potentiometer and measuring with a multimeter.

6. Maintenance

  • Keep Clean: Keep the circuit board clean and free from dust, dirt, and moisture. Use a soft, dry brush or compressed air for cleaning.
  • Avoid Overloading: Do not exceed the maximum output current of 1A to prevent damage to the components.
  • Check Connections: Periodically check all wire connections and solder joints to ensure they are secure.
  • Storage: Store the power supply in a dry, cool environment when not in use.

7. Troubleshooting

  • No LED Light / No Output:
    • Check input power source: Ensure it is connected correctly and providing the specified voltage.
    • Check polarity of diodes and electrolytic capacitors: Incorrect polarity will prevent the circuit from working.
    • Inspect solder joints: Look for cold joints, bridges (shorts), or unsoldered pins.
    • Check LED polarity: If the LED is reversed, it won't light up.
  • Output Voltage Not Adjustable:
    • Check potentiometer (RP1) connections: Ensure it is soldered correctly and not damaged.
    • Check LM317 (VR1) connections: Ensure all three pins are properly soldered.
    • Verify resistor values: Ensure R1 and R2 are the correct values.
  • Output Voltage Unstable:
    • Check electrolytic capacitors (C1, C2): Ensure they are correctly installed and not faulty.
    • Ensure input power is stable: Unstable input will lead to unstable output.

8. User Tips

  • Beginner-Friendly: This kit is excellent for learning basic soldering and electronics principles. Take your time during assembly.
  • Verify Components: Before soldering, it's a good practice to check component values (especially resistors) with a multimeter if you have one.
  • Test Before Use: Always test the output voltage with a multimeter before connecting any valuable electronic devices.
  • Versatile for Small Projects: Users find this kit very useful for powering small projects, LED lighting, or as a variable voltage source for testing.

9. Warranty and Support

This product is a DIY kit. While every effort has been made to ensure the quality of components, successful operation depends on correct assembly. We recommend reviewing all instructions carefully before starting assembly.

For technical support or inquiries regarding missing/defective components, please contact your seller directly.

© 2023 All Rights Reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.