1. Product Overview
This Feyree EV Charger is designed for electric vehicle AC charging. Its simple design supports Type2, Type1, TS-NACS, and GB/T specifications. It offers plug-and-play charging with multiple safety protection functions, good dustproof and waterproof capabilities, ensuring safe outdoor operation.
1.1 Package Contents
Upon unboxing, you should find the following components:
- Wallbox (main control unit with cable and charging gun)
- Plug (CEE plug)
- Wallbox Holder
- Charging Gun Holder
- User Manual
- Mounting Screws and Wall Plugs
Video: Unboxing and overview of the Feyree EV Charger components.
Image: All components included in the Feyree EV Charger package.
1.2 Dimensions
The dimensions of the charging control box are as follows:
- Length: 355mm
- Width: 152mm
- Depth: 85mm
Image: Dimensions of the EV Charger control box.
2. Safety Instructions
Please read and understand all safety instructions before using the EV charger.
- Warning: The charging station must be grounded (PE) in order to use it properly.
- Warning: Do not place flammable, explosive or combustible materials, chemicals, combustible vapors or other hazardous materials near the charging station.
- Warning: Keep the charging plug head clean and dry. If dirty, wipe it with a clean and dry cloth. It is strictly forbidden to touch the charging plug core by hand when it is charged.
- Warning: It is strictly forbidden to use the charging station when the charging plug or charging cable is defective, cracked, worn, broken or when the charging cable is exposed.
- Warning: Do not attempt to disassemble, repair or modify the charging station. If you need to repair or modify it, please contact the relevant staff. Improper operation may cause charging station damage, water leakage, leakage of electricity, short circuit, electric shock and other risks.
- Warning: Use with caution during thunderstorms.
- Warning: Children should not approach or use the charging station during the charging process to avoid electric shock.
- Warning: Do not drive the car while it is charging. You can only start charging when the car is stationary. For hybrid cars, please turn off the engine before charging.
- Warning: In case of emergency during the operation of the product, press the emergency stop button immediately to cut off all input and output power.
- Warning: The use of the charging post is prohibited in the following cases and the manufacturer should be contacted immediately:
- Bad charging station shell
- When the charging cable on the charging station is damaged, cracked, frayed, broken, etc.
- Lightning strikes charging station
- Accidents or fires near charging stations
- Water in the charging station
- The length of the charging cable on charging station is not long enough to connect to the car, an extension cable needs to be installed.
3. Specifications
3.1 General Product Properties
| Attribute | Value |
|---|---|
| Brand Name | feyree |
| Charger Type | Portable & Wallmounted EV charger |
| Type | GB/T Charger |
| Power (W) | 7kw |
| Current | 8A-10A-13A-16A-20A-25A-32A Adjustable |
| Voltage | 85V-264V |
| Input Frequency | 50Hz-60Hz |
| Number of Phases | Single Phase |
| Cable Length | 5m |
| Material | Copper Alloy, Silver Plating |
| IP Rating | IP66 |
| RCD | TypeB AC30mA+ DC6mA |
| Operating Temperature | -30 ~ +55°C |
| Wireless Support | Wifi |
| Touchscreen | No |
| Weight | 3.9KG |
| High-concerned chemical | None |
3.2 GB/T Parameter Introduction (7.6kW)
| Parameter | Value (7.6kW) |
|---|---|
| Power Rating | 7.6kW |
| APP | Yes |
| Type B RCD | Yes |
| Leakage protection | TypeB AC 30mA + DC 6mA |
| Power supply system | Single Phase |
| Rated voltage | 85V-264V |
| Rated current | 8-10-13-16-20-25-32A |
| Input Frequency | 50Hz/60Hz |
| Charger Plug | IP66 |
| Charger Box | IP66 |
| Working temperature | -35°C ~ +55°C |
| Storage temperature | -40°C ~ +80°C |
| Standby power | <3W |
| Working humidity | 5%~95% non-condensation |
| Cable Specification | 3G 6mm²+1*0.5mm² |
3.3 Control Box Functions
- Leakage protection (restart recovery)
- Overvoltage and undervoltage protection (self-test recovery)
- Lightning protection
- Overcurrent protection
- Overheat protection
- Grounding protection
- Appointment Time
- WIFI
3.4 Product Performance
- Charging plug according to GB/T20234 standard
- Charging control box in accordance with IEC61851 control principle
- Insulation resistance: >1000Ω
- Terminal temperature rise: <50K
- Mechanical life: Charging Plug plugging and unplugging times (Non operating state) >10000 times
- External impact: Charging Station Plug can withstand the 1-meter drop and 2 tons of vehicle crushing
- Altitude: ≤2000m
- With emergency stop function
Image: Key features and specifications of the EV Charger.
Image: High-quality materials used in the EV Charger.
Image: 5-meter TUV-Certified cable diagram.
Image: Compatibility with various EV brands.
4. Setup
4.1 Mounting the Wallbox and Gun Holder
The Feyree EV Charger is designed for both portable and wall-mounted use. To wall-mount the charger:
- Choose a suitable location for the wallbox holder and gun holder, ensuring it is within reach of your vehicle and a power outlet, and away from flammable materials.
- Use the provided screws and wall plugs to securely attach the wallbox holder to the wall.
- Mount the gun holder next to the wallbox holder for convenient storage of the charging gun.
4.2 Connecting to Power
Ensure the CEE plug is clean and dry before connecting it to a compatible power outlet. The charger supports various CEE plug types depending on the power rating (7KW, 11KW, 22KW). For this 7KW 32A model, ensure you have the correct CEE plug type (e.g., Model A or Model B as shown in the image below).
Image: Two types of CEE plugs available for different power ratings.
5. Operating Instructions
5.1 Control Box LCD Display
The LCD display provides real-time information about the charging process. Key indicators include:
- Wifi State: Shows connection status (Connection waiting, Connect, Not connected).
- Real-time Temperature: Current operating temperature.
- Charging Current: Current flowing to the vehicle.
- Charging Voltage: Voltage supplied to the vehicle.
- Real-time Power: Instantaneous power consumption.
- Power Consumption: Total energy consumed.
- Charging State: Current status of charging.
- Set Current: The current limit set for charging.
- Set Delay Time: The set delay before charging starts.
- Set Charging Time: The duration for which charging is scheduled.
- Charging duration / Delay charging countdown: Timer for active charging or delay.
Image: Feyree EV Charger main display.
5.2 Button Operations
The control box features four main buttons (A, D, T) and a central button for emergency stop/reset.
Image: Smart Charger button functions for current, delay, and time settings.
5.2.1 Adjusting Charging Current
When the charging plug is not inserted into the car, press the A button on the panel to adjust the charging current. The current setting range is 8A-10A-13A-16A-20A-25A-32A.
Video: Demonstrating how to adjust the charging current using the 'A' button.
5.2.2 Setting Delay Charging Time
When the charging plug is not inserted into the car, touch the D button on the panel to modify the delayed charging time. The device will start charging after the set number of hours (from 0 to 15 hours, each touch increases by one hour).
Video: Demonstrating how to set the delay charging time using the 'D' button.
5.2.3 Setting Charging Duration
When the charging plug is not inserted into the car, touch the T button on the panel to modify the charging duration. The charger will continue charging for the set number of hours (from 0 to 15 hours, each touch increases by one hour) and then stop automatically.
Video: Demonstrating how to set the charging duration using the 'T' button.
5.2.4 Accessing the Menu
Long press the settings button (gear icon) for 5 seconds to enter the menu interface.
Video: Demonstrating how to access the menu by long-pressing the settings button.
5.2.5 Menu Navigation
Once in the menu, use the directional buttons (upward/downward shift, enter, back) to navigate and adjust parameters.
- Charge Plan: Set current, delay start, and charge time.
- Charge Log: Records the last 10 charging statuses for fault diagnosis.
- Setting:
- Hotkeys: Turn on/off the lock button.
- Reset Wifi: Clear network configuration.
- Ground Check: Turn on/off grounding (PE) detection.
- About Device: Displays device information like power, software version, RCD type, and manufacturing date.
Video: Demonstrating menu navigation and settings adjustment.
5.3 Using the Smart APP
The charger supports Wi-Fi and Bluetooth connectivity for smart control via an app.
- Download the "Smart Life" or "Tuya Smart" app from your mobile app store.
- Open the app, ensure your phone's Wi-Fi and Bluetooth are enabled.
- Select "Add Device" and follow the on-screen instructions to add your charger. You may need to enter your Wi-Fi information.
- Once connected, you can monitor charging status, adjust current, set delay times, and schedule charging periods to save on electricity bills.
Image: App interface for scheduling charging periods.
Image: App control via Bluetooth without Wi-Fi.
Video: Demonstrating app connection and control of the charger.
6. Maintenance
- Regularly inspect the charging cable and plug for any signs of damage, cracks, fraying, or exposure. Do not use the charger if any damage is found.
- Keep the charging plug head clean and dry. If it becomes dirty, wipe it with a clean and dry cloth. Avoid touching the charging plug core by hand.
- Ensure the charging station is kept away from excessive heat sources and that the ambient temperature is below 50°C.
7. Troubleshooting
This section provides guidance for common issues. If the problem persists, contact customer service.
| Fault Name | Reason for Failure | Recommendations |
|---|---|---|
| Over Voltage | AC input voltage is too high | 1. Ask an electrician to measure the input voltage of the charger's power distribution box. 2. If the actual voltage is over 264V for a short time, wait for the power system to restore itself to the normal voltage range. 3. If the actual voltage is over 264V for a long time, please contact the local power supply department. 4. If the actual voltage of the electrical system in your home is less than 264V, please contact us. |
| Under Voltage | AC input voltage is too low | 1. Ask an electrician to measure the input voltage of the charger's power distribution box. 2. If the actual voltage is less than 85V for a short time, wait for the power system to restore itself to the normal voltage range. 3. If the actual voltage is less than 85V for a long time, please contact the local power supply department. 4. If the actual voltage of the electrical system in your home is over 85V, please contact us. |
| Over Current | AC input current is too high | 1. Cut off the power of the charger's power distribution box right away. 2. Check the charging plug for foreign objects and the car's on-board charger for abnormalities. 3. After troubleshooting the above problems, reconnect the power supply. If the fault still exists, please contact us. |
| Over TEMP | Charger internal temperature greater than 85°C | 1. Check that there is no other heat generating equipment or devices next to the charging station and make sure that the ambient temperature is below 50°C. 2. If the problem cannot be solved, please contact us. |
| Elec leakage | Leakage is greater than the following values: TypeA:(60Hz)AC20mA/(50Hz)AC30mA, TypeB: AC 30mA+DC 6mA | 1. Cut off the power of the charger's power distribution box right away. 2. Check the charging plug for foreign objects and check the car for electrical leakage. 3. After troubleshooting the above problems, reset leakage protector, reconnect the power supply. If the fault still exists, please contact us. |
| Leakage self check | The sensor for detecting leakage is abnormal | 1. Cut off the power of the charger's power distribution box right away. 2. Check whether the output cable of the charging station is broken or connected to ground. 3. After troubleshooting the above problems, reconnect the power supply. If the fault still exists, please contact us. |
| PE Fault | Poor grounding or incorrect wiring | 1. Cut off the power of the charger's power distribution box right away. 2. Check if the charging station is grounded properly. 3. After troubleshooting the above problems, reconnect the power supply. If the fault still exists, please contact us. |
| Err:cp | Charging plug CC/CP connection abnormality | 1. Check if the wiring of the charging plug is correct. 2. After troubleshooting the above problems, if the fault still exists, please contact us. |
| Err:Reset | Reset button is pressed | 1. Check if the red button on the right is pressed. If it is pressed, rotate it back to reset. 3. After troubleshooting the above problems, if the fault still exists, please contact us. |
8. Charging Status and Indicator Light
The charger uses a green light to indicate its status:
| Charging Status | Green Light | Blue Light | Red Light | Description |
|---|---|---|---|---|
| Ready | Ever-bright | / | / | Power-up for self-test or reset |
| Connect | Flashing | / | / | Detection point 1 voltage is 9 ± 0.8 V. |
| Charging | / | Breathing | / | Detection point 1 voltage is 6 ± 0.8 V, relay closed |
| Finish | / | Ever-bright | / | Charging finished |
| Err:CP | / | / | Flash 1 time(0.5S) | Detection point 1 voltage is 9.8V<U<11.2V; 6.8V<U<8.2V; 12.8V<U or U<5.2V; relay opened |
| Under Voltage | / | / | Flash 2 time(0.5S) | Single-phase: voltage <85V, Three-phase: <304V |
| Over Voltage | / | / | Flash 3 time(0.5S) | Single-phase: voltage > 264V, Three-phase: > 457V |
| Elec Leakage | / | / | Flash 4 time(0.5S) | Relay is opened, it will be closed if re-powered after troubleshooting. |
| Over Current | / | / | Flash 5 time(0.5S) | The line current keep at le+2<I≤le+4 for 5 seconds, the relay is opened, then restarted automatically after 10 seconds. It will permanently disconnect after three repetitions. At I> le+4, the relay is disconnected and the charging is finished. |
| Over Temp | / | / | Flash 6 time(0.5S) | Temperature > 85°C, the relay is opened. When the temperature is < 65 °C, charging restarts. |
| Err:Reset | / | / | Flash 7 time(0.5S) | Emergency stop button is pressed, the relay is opened, and it is allowed to close only after the fault is solved. |
9. User Tips
- Emergency Stop: The charger features a one-button emergency stop. You do not need to go to the car to switch off charging in an emergency, ensuring safety.
- Error Reset: If you see an "err:reset" message on the screen after installing the wall-box, simply press the central button to restart the wallbox. This usually resolves the issue.
- Compatibility Check: Always ensure your EV is compatible with the GB/T charging standard before use.
- Voltage Awareness: Be mindful of your local voltage. If the charger operates at a lower voltage than expected, consult the troubleshooting section or an electrician.
10. Warranty and Support
10.1 Two-Year Warranty
Feyree offers a two-year warranty to customers who have purchased an original Feyree product.
10.2 Lifetime Technical Support
In case of any product-related issues, we encourage you to reach out to us, providing pictures and videos for further assistance.
10.3 Exclusions
The warranty does not cover:
- Any product damage resulting from failure to follow the recommended guidelines.
- Damage caused by unauthorized disassembly of the machine or seeking maintenance from a non-designated service center.
- Purchased non-original Feyree products.
- Any modifications or do-it-yourself alterations carried out without guidance from a licensed electrician.
10.4 Customer Service Contact
E-mail: tina@feyree.com
11. FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference; (2) this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates and uses can radiate radio frequency energy, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Note: The Grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. Such modifications could void the user's authority to operate the equipment.
The device has been evaluated to meet general RF exposure requirement. To maintain compliance with FCC's RF exposure guidelines, the distance must be at least 20cm between the radiator and your body, and fully supported by the operating and installation configurations of the transmitter and its antennas.