1. Introduction
Thank you for choosing REDRAGON SMD RGB MX Low Profile Mechanical Keyboard Switches. These switches are designed to provide a tactile, clicky, linear, or silent typing experience with multicolor backlight compatibility and hot-swap functionality. This manual provides essential information for installation, operation, and maintenance.
Important Compatibility Note: These switches are specifically designed as 5.5mm 3-pin ultra-low profile switches, with a height of approximately 12mm. They are compatible with REDRAGON brand special short switch keyboards, including models K539RGB, K603P, K607P, K615P, K618RGB, K621RGB, K624P, and other keyboards with 5.5mm pinhole spacing. Please confirm your keyboard's pinhole spacing before purchase.

2. Specifications
2.1 General Product Attributes
| Attribute | Value |
|---|---|
| Brand Name | REDRAGON |
| Switches Hot swap | Yes |
| Backlight Type | MULTICOLOR |
| Operation Style | Mechanical |
| Origin | Mainland China |
| Certification | CE, FCC |
2.2 Switch Dimensions
- Pinhole Spacing: 5.5mm (ultra-low switch)
- Switch Height: Approximately 12mm (ultra-low switch)


2.3 Switch Parameters by Type
| Parameter | Blue Switch | Black Switch | Brown Switch | Red Switch |
|---|---|---|---|---|
| Total Stroke | 3.00mm | 3.00mm | 3.00mm | 3.00mm |
| On Stroke | 1.20±0.5mm | 1.20±0.5mm | 1.20±0.5mm | 1.20±0.5mm |
| Conduction Strength | 45±10gf | 55±10gf | 45±10gf | 50±10gf |
| Tactile Strength | 55±10gf | N/A (Linear) | 55±10gf | N/A (Linear) |
| Haptic Travel | 1.00mm | N/A (Linear) | 1.00mm | N/A (Linear) |
| Minimum Trigger Force | 30 gf Min | 50 gf Min | 30 gf Min | 40 gf Min |
| Stop Strength | 70 gf Max | N/A | 70 gf Max | 70 gf Max |
| Termination Force | N/A | 80 gf Max | N/A | N/A |

3. Setup and Installation
These switches are hot-swappable, allowing for easy replacement without soldering. Follow these steps to install or replace your mechanical keyboard switches:
- Remove Keycap: Use a keycap puller to gently remove the keycap from the switch you wish to replace.
- Remove Old Switch: Use a professional shaft puller (switch puller) to carefully pull out the existing switch body from the keyboard PCB.
- Prepare New Switch: Ensure the pins on the new switch are straight. Correct the installation position of the shaft to be changed. Note that the pins cannot be crooked, as this may damage the PCB or the switch.
- Align Switch: Place the new switch onto the detent (the socket on the PCB).
- Insert Switch: Gently tap the new switch into the card position until it is fully seated. Ensure both pins are correctly aligned with the PCB sockets.
- Attach Keycap: Once the switch is securely in place, attach the keycap back onto the switch stem.

4. Operation
The REDRAGON SMD RGB MX Low Profile switches offer various typing experiences based on their type:
- Blue Switch: Known for a distinct clicky sound and tactile bump, providing audible and physical feedback with each keystroke.
- Black Switch: A linear switch with a smooth, consistent keystroke without a tactile bump or audible click. Requires slightly more force than Red switches.
- Brown Switch: A tactile switch with a noticeable bump but no audible click, offering a balance between typing and gaming.
- Red Switch: A linear switch with a smooth, consistent keystroke, ideal for gaming due to its fast actuation and light press force.
These switches support multicolor backlighting, allowing your keyboard's RGB lighting to shine through for a vibrant aesthetic.

5. Maintenance
REDRAGON switches are designed to be dustproof and waterproof, enhancing their durability and lifespan. To maintain optimal performance:
- Regular Cleaning: Periodically remove keycaps and use compressed air or a soft brush to clean dust and debris from around and within the switches.
- Spill Management: While switches are waterproof, it is always best practice to clean up any spills immediately to prevent potential damage to the keyboard's PCB.

6. Troubleshooting
- Switch Not Registering:
- Ensure the switch is fully seated in the PCB socket.
- Check for bent pins on the switch. Gently straighten them if necessary before re-inserting.
- Verify keyboard compatibility; these switches require 5.5mm pinhole spacing.
- Inconsistent Keystrokes:
- Remove the keycap and inspect the switch for any debris or obstructions.
- If the issue persists, consider replacing the switch.
- Backlight Issues:
- Ensure the switch is correctly installed and making proper contact.
- Check your keyboard's software or onboard controls for backlight settings.
7. User Tips
- Verify Compatibility: Always double-check your keyboard's pinhole spacing (5.5mm) before purchasing to ensure these switches are compatible.
- Handle Pins Carefully: While some bent pins upon arrival are common and easily fixable, always handle switches with care to avoid bending the pins during installation.
- Blue Switch Sound: The low-profile Blue switches tend to produce a less noisy, yet still pleasant, click compared to standard profile Blue switches.
- Brown Switch Comfort: Brown switches offer a comfortable typing experience with good tactile feedback, reducing accidental key presses.
8. Warranty and Support
For warranty information and technical support, please refer to the official REDRAGON website or contact the seller, Stone's Store, directly. Keep your purchase receipt as proof of purchase.