Aramox TSH-06F

Contents

Aramox TSH-06F Integrated Circuit Tester User Manual

Model: TSH-06F

1. Introduction

The Aramox TSH-06F Integrated Circuit Tester is a versatile and portable instrument designed for microelectronics engineers and maintenance personnel. It efficiently tests a wide range of integrated circuits and transistors, offering multiple test modes and automatic identification features to streamline your work.

This manual provides detailed instructions for the proper setup, operation, and maintenance of your TSH-06F tester. Please read it thoroughly before using the device.

2. Key Features

  • Multiple Test Modes: Includes 5V mode, 3.3V mode, and AUTO mode for flexible testing.
  • Wide Compatibility: Supports testing of 74HC series, 74LS series, CD4000 series, HEF400 series, 4500 series ICs, operational amplifiers, interface chips, and optocouplers.
  • Efficient Measurement: Built-in data models for over 1,300 chip types and 420 transistor types, covering most common devices within 24 pins.
  • Automatic Identification: Features automatic transistor identification and voltage regulator voltage identification.
  • Portable Design: Small and lightweight, making it convenient for on-the-go circuit testing.
  • Automatic Shutdown: Conserves battery life by automatically shutting down after 60 seconds of inactivity.

3. Package Contents

Please check the package carefully upon receipt to ensure all components are present and in good condition.

  • 1 x TSH-06F Integrated Circuit Tester (Batteries not included)
  • 3 x SOP Adapters (SOP28, SOP20, SOP16)
  • 1 x User Manual
TSH-06F IC Tester with SOP28, SOP20, SOP16 adapters
The TSH-06F IC Tester shown with its included SOP28, SOP20, and SOP16 adapters.

4. Setup

4.1. Battery Installation

  1. Locate the battery compartment on the back of the tester.
  2. Open the battery back cover.
  3. Insert two (2) 1.5V AA batteries, ensuring correct polarity.
  4. Close the battery cover securely.
Back of the TSH-06F IC Tester with battery compartment open
The battery compartment on the back of the tester, requiring two AA batteries.

4.2. Powering On/Off

  • Power On: Press and hold the 'Enter' key for more than 2 seconds. The current battery voltage will be displayed upon boot-up.
  • Power Off (Immediate): Navigate to the 'OFF' directory and press 'Enter'.
  • Power Off (Forced): Press and hold the 'Enter' key in any directory for more than 10 seconds.
  • Automatic Shutdown: The device will automatically shut down after 60 seconds of inactivity.

4.3. Adapter Installation

The tester comes with SOP adapters (SOP28, SOP20, SOP16) for different IC packages. To use an adapter:

  1. Identify the correct SOP adapter for your IC.
  2. Carefully insert the adapter's pins into the ZIF (Zero Insertion Force) socket on the tester. Ensure proper alignment.
  3. Lower the ZIF socket lever to secure the adapter.
Diagram showing SOP28, SOP20, SOP16 adapters and their labels
The SOP28, SOP20, and SOP16 adapters for various IC packages.

5. Operating Instructions

5.1. Controls Overview

The tester features 7 buttons on its panel:

  • Up/Down Arrows: Used to navigate through menus, adjust catalogs, and change model numbers.
  • Left/Right Arrows: Used to move the cursor to select items for modification.
  • Enter Key: Used to switch the machine, execute test commands, and confirm selections.
  • 'O' Key (Shortcut): Quick shutdown (for 06 type).
  • 'P' Key (Shortcut): Backlight control (for 06 type).
Front view of the TSH-06F IC Tester showing buttons and display
Front panel of the TSH-06F IC Tester with its control buttons and LCD display.

5.2. Performing a Test

  1. Ensure the tester is powered on and batteries are sufficiently charged.
  2. Select the appropriate test mode (5V, 3.3V, or AUTO) using the navigation keys.
  3. If using an adapter, ensure it is correctly installed in the ZIF socket.
  4. Carefully insert the IC or component to be tested into the ZIF socket (or adapter), ensuring correct orientation and pin alignment. Lower the ZIF socket lever to secure the component.
  5. Press the 'Enter' key to initiate the test.
  6. The LCD display will show the test results, including identification of the component and its status (e.g., 'Pass', 'Fault').
Video demonstrating the TSH-06F IC Tester, including adapter installation, battery insertion, and basic operation with test results shown on the LCD.

5.3. Supported Component Types

The TSH-06F tester can identify and test the following:

  • IC Chips: 74HC series, 74LS series, CD4000 series, HEF400 series, 4500 series.
  • Transistors: Automatic identification of various transistor types.
  • Optocouplers: Testing for functionality.
  • Amplifiers: Operational amplifiers.
  • Regulatory Tubes: Voltage regulator voltage value identification.
  • Interface Chips: General interface driver devices.

6. Maintenance

6.1. Battery Care

Always replace batteries when the low battery indicator appears or if the device behaves erratically. Low voltage can compromise test reliability and may cause the device to shut down unexpectedly.

6.2. Storage

Store the tester in a dry, cool place away from direct sunlight and extreme temperatures. If storing for extended periods, remove the batteries to prevent leakage.

6.3. Cleaning

Wipe the exterior of the device with a soft, dry cloth. Do not use abrasive cleaners or solvents. Ensure no liquids enter the device, especially the ZIF socket or display.

7. Troubleshooting

Problem Possible Cause Solution
Device does not power on. Dead or incorrectly installed batteries. Check battery polarity and replace with fresh AA batteries.
Inaccurate test results or 'Fault' indication for known good component. Low battery voltage; incorrect component insertion; wrong test mode selected. Replace batteries. Re-insert component ensuring correct orientation and good contact. Select the appropriate test mode (e.g., 5V, 3.3V, or AUTO).
Device shuts down unexpectedly. Low battery voltage; automatic shutdown due to inactivity. Replace batteries. If not due to inactivity, ensure batteries are fresh.
Display is dim or unreadable. Backlight off; low battery. Press the 'P' key to toggle backlight. Replace batteries if dimness persists.

8. Specifications

Attribute Detail
Item Type Integrated Circuit Meter
Model TSH-06F
Brand Name Aramox
Material ABS
Power Supply 2 x 1.5V AA Batteries (NOT Provided)
Power Source AC (Implied for charging, but device is battery-powered for operation)
Test Chips 74HC series, 74LS series, CD4000 series, HEF400 series, 4500 series
Test Modes 5V Mode, 3.3V Mode, Auto Mode
Scope of Test IC Chip, Transistor, Optocoupler, Amplifier, Regulatory Tube
Size 13.5 x 7 x 2.5 cm
DIY Supplies Electrical
Certification CE
Origin Mainland China

9. User Tips

  • Always ensure the component is correctly seated in the ZIF socket or adapter before initiating a test to prevent damage and ensure accurate readings.
  • Keep spare AA batteries on hand, as low battery power can lead to unreliable test results or unexpected shutdowns.
  • For sensitive components, consider using the 3.3V test mode if applicable, or consult the component's datasheet for recommended test voltages.

10. Frequently Asked Questions (FAQ)

Q: What types of components can this tester identify?
A: The TSH-06F can identify and test 74HC/LS series, CD4000 series, HEF400 series, 4500 series ICs, operational amplifiers, interface chips, optocouplers, transistors, and voltage regulator tubes.
Q: What are the available test modes?
A: The tester offers 5V mode, 3.3V mode, and an AUTO mode for automatic detection.
Q: How is the device powered?
A: It is powered by two (2) 1.5V AA batteries (not included).
Q: Does it have an automatic shutdown feature?
A: Yes, the device will automatically shut down after 60 seconds of no operation to conserve battery life.

11. Warranty and Support

For detailed information regarding warranty coverage and technical support, please refer to the official user manual PDF available at: TSH-06F User Manual (PDF).

If you encounter any issues not covered in this manual or require further assistance, please contact the seller or manufacturer's customer support.

Customer service representative image
For support, please contact customer service.

© 2024 Aramox. All rights reserved.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.