WINXU S810 E-bike Brushless Motor Controller Kit

Contents

WINXU E-bike Brushless Motor Controller and S810 LED Display User Manual

Model: S810 E-bike Brushless Motor Controller Kit

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your WINXU E-bike Brushless Motor Controller and S810 LED Display. This kit is designed for electric bicycle and scooter repair and conversion, offering reliable control for various brushless motors. Please read this manual thoroughly before installation and use to ensure proper function and safety.

WINXU Brushless Motor Controller and S810 LED Display
The WINXU Brushless Motor Controller and S810 LED Display kit.

2. Product Overview

The WINXU E-bike Brushless Motor Controller and S810 LED Display kit provides essential components for managing your e-bike or scooter's motor. The controller is a brushless dual-mode unit, compatible with a wide range of brushless motors. The S810 LED display serves as your operation panel, providing real-time information and control over your electric vehicle.

2.1 Components

  • Brushless Dual-Mode Controller: The main control unit for the motor.
  • S810 LED Display: User interface for monitoring and controlling the e-bike/scooter.
S810 LED Display close-up
Close-up view of the S810 LED Display.
Side view of the Brushless Motor Controller
Side view of the Brushless Motor Controller unit.
Back view of the S810 LED Display with mounting bracket
Back view of the S810 LED Display, showing the mounting bracket.

3. Specifications

FeatureSpecification
TypeController
Brand NameWINXU
OriginMainland China
Input Voltage24V / 36V / 48V
Power Options250W / 350W / 500W
Current13A (250W) / 15A (350W) / 22A (500W)
Motor TypeBrushless motor
Package Length18 cm
Package Width10 cm
Package Height12 cm
Package Weight0.45 kg
Controller size comparison for 250W/350W and 500W models
Physical dimensions of the 250W/350W and 500W controllers.

4. Safety Information

Always prioritize safety when working with electrical components. Failure to follow these guidelines may result in injury or damage to the product.

  • Ensure the power source is disconnected before performing any installation, wiring, or maintenance.
  • Verify all connections are secure and correctly insulated to prevent short circuits.
  • Do not expose the controller or display to water or extreme weather conditions unless explicitly rated for such use.
  • If you are unsure about any step, seek professional assistance.
  • Keep out of reach of children.

5. Installation and Setup

Careful installation is crucial for the proper functioning of your e-bike system. Refer to the wiring diagram and the installation video for guidance.

5.1 Pre-installation Checks

  • Ensure your motor is a brushless type.
  • Confirm your PAS (Pedal Assist Sensor) is a dual-hall type.
  • Verify your throttle is a 5V Hall throttle.
  • The controller includes a 'learning wire' for initial motor pairing.

5.2 Wiring Diagram

The following diagram illustrates the connections for the 250W Brushless Controller. Connections for 350W and 500W controllers will be similar, but always refer to the labels on your specific controller.

Detailed wiring diagram for 250W Brushless Controller
Detailed wiring diagram for the 250W Brushless Controller, showing connections for power, display, sensors, and motor.

Key Connections:

  • Power Input: Connects to your battery.
  • Power Lock: For ignition/key switch.
  • LED/LCD Display: Connects to the S810 display.
  • Cruise: For cruise control function.
  • PAS Sensor: Connects to the Pedal Assist Sensor.
  • Power-off Brake: Connects to brake levers with power cut-off function.
  • Automatic Detection (Learning Wire): Used for initial motor pairing.
  • Throttle: Connects to the throttle grip.
  • Motor Hall: Connects to the motor's Hall sensors.
  • Motor U, V, W: Connects to the motor's phase wires.

5.3 Installation Video Guide

For a visual guide on installation, please refer to the sample video below. This video demonstrates the general installation process and can be helpful before or during your setup.

Installation sample video for the controller kit.

6. Operation

The S810 LED Display provides intuitive control over your e-bike or scooter.

6.1 S810 LED Display Functions

  • Power Button: Press and hold to turn the system ON/OFF.
  • Light Button: Activates/deactivates the e-bike's lights (if connected).
  • Mode Button: Cycles through different display modes or settings.
  • 5KM/H Button: Activates a low-speed walk assist mode.
  • Assist Level Indicators (+/-): Adjusts the level of motor assistance.
  • Battery Level Indicator: Shows the remaining battery charge.

7. Maintenance

To ensure the longevity and optimal performance of your controller and display, follow these maintenance guidelines:

  • Keep the controller and display clean and free from dust and debris.
  • Regularly check all electrical connections for tightness and signs of wear or corrosion.
  • Avoid exposing the components to excessive heat, cold, or moisture.
  • Do not attempt to open or modify the controller or display, as this may void any warranty and cause damage.

8. Troubleshooting

If you encounter issues with your e-bike system, consider the following troubleshooting steps:

  • No Power: Check battery connections, power lock switch, and ensure the display is properly connected.
  • Motor Not Responding: Verify all motor phase wires and Hall sensor connections. Ensure the throttle is functioning correctly. Use the 'learning wire' function if the motor is new or recently reconnected.
  • Inconsistent Pedal Assist: Check the PAS sensor installation and wiring. Ensure it is a dual-hall type.
  • Display Not Working: Check the display cable connection to the controller. Ensure the main power is on.
  • Error Codes: If the display shows an error code, consult the specific error code documentation for the S810 display (if available) or contact support.

9. User Tips

  • Initial Setup: When first connecting the controller to a motor, use the 'learning wire' feature to allow the controller to automatically identify the motor's phase sequence and Hall sensor type. This typically involves connecting the learning wires, turning on the system, waiting for the motor to spin, and then disconnecting the learning wires.
  • Component Compatibility: Always ensure that your PAS sensor is a dual-hall type and your throttle is a 5V Hall throttle for optimal compatibility with this controller.
  • Secure Wiring: After installation, use zip ties or electrical tape to neatly secure all wires, preventing them from snagging or getting damaged during use.

10. Warranty and Support

For any technical assistance, warranty claims, or further inquiries, please contact WINXU customer support. Keep your purchase records handy when contacting support.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.