Introduction
This manual provides comprehensive instructions for the Yovanxer AC114-1 RF433 Wireless Remote Control. This device is designed to operate automated curtains, specifically compatible with A-OK motors, using a reliable 433 MHz radio frequency signal. Please read this manual thoroughly before installation and operation to ensure proper use and longevity of your device.
Specifications
| Feature | Detail |
|---|---|
| Product Brand | Yovanxer |
| Model Number | AC114-1 |
| Wireless Communication | RF (Radio Frequency) |
| Frequency | 433 MHz |
| Transmitting Frequency | 433MHz |
| Use | Automated curtains |
| Voltage | 3V |
| Supported Motor | All A-OK motors |
| Controllable Range | Up to 60 meters (indoor, through walls) |
| Product Weight | 84g |
| Battery | Not included (Requires 2x AAA batteries) |
| Package | Yes |
| Remote Dimensions (L x W) | 124.8mm x 40mm |
| Origin | Mainland China |
Setup
1. Unboxing and Inspection
Carefully unpack the remote control and its accessories. Verify that all components are present and undamaged. The package should include the AC114-1 remote control and a wall-mount base.
2. Battery Installation
The AC114-1 remote control requires two AAA batteries (not included). To install:
- Locate the battery compartment on the back of the remote control.
- Slide open the rear cover.
- Insert two AAA batteries, ensuring correct polarity (+/-).
- Close the rear cover securely.
3. Mounting the Remote (Optional)
The remote control comes with a wall-mount base for convenient storage. To mount:
- Choose a suitable location for the base, within easy reach.
- Use appropriate screws (not included) to secure the base to the wall.
- Slide the remote control into the base.
4. Pairing with A-OK Motor
To control your automated curtains, the remote control must be paired with your A-OK motor. The exact pairing procedure may vary slightly depending on your specific A-OK motor model. Generally, the process involves:
- Ensure your A-OK motor is powered on and in pairing mode (refer to your A-OK motor's instruction manual for specific steps to enter pairing mode).
- On the AC114-1 remote, locate the 'Settings key' (often a small button inside the battery compartment or on the back, as indicated in Figure 1).
- Press and hold the 'Settings key' on the remote control for a few seconds until the motor responds (e.g., jogs slightly, beeps, or indicates successful pairing).
- Test the remote control's functions (Up, Down, Stop) to confirm successful pairing.
Operating Instructions
Remote Control Layout
- Channel Display: Shows the currently selected control channel.
- Up Key (▲): Moves the curtain upwards (opens).
- Down Key (▼): Moves the curtain downwards (closes).
- Stop Key (●): Stops the curtain's movement.
- Left Click (◀): Used to switch to the previous control channel.
- Right Click (▶): Used to switch to the next control channel.
Basic Operation
- Select Channel: Use the 'Left Click' or 'Right Click' buttons to select the desired channel for the curtain you wish to control. The 'Channel Display' will show the active channel.
- Open Curtain: Press the 'Up Key' (▲). The curtain will move upwards.
- Close Curtain: Press the 'Down Key' (▼). The curtain will move downwards.
- Stop Curtain: Press the 'Stop Key' (●) at any point to halt the curtain's movement.
Maintenance
Cleaning
To clean the remote control, use a soft, dry cloth. Do not use abrasive cleaners, solvents, or wet cloths, as these can damage the surface or internal components.
Battery Replacement
When the remote control's range decreases or it becomes unresponsive, it's likely time to replace the batteries. Follow the 'Battery Installation' steps in the Setup section to replace the two AAA batteries. Always dispose of old batteries responsibly according to local regulations.
Storage
Store the remote control in a cool, dry place, away from direct sunlight and extreme temperatures. If not in use for an extended period, it is recommended to remove the batteries to prevent leakage.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Remote not responding | Dead or low batteries Remote not paired with motor Obstruction between remote and motor | Replace batteries Re-pair the remote with the motor (see Setup section) Ensure clear line of sight or reduce distance |
| Short operating range | Low batteries Excessive interference Thick walls or metal structures | Replace batteries Move away from other electronic devices Reduce distance to motor |
| Curtain moves in wrong direction | Motor direction setting incorrect | Refer to your A-OK motor's manual for instructions on reversing motor direction. |
| Cannot switch channels | Remote is a single-channel model (if applicable) Buttons are stuck or damaged | Verify remote model. If single channel, it cannot switch. Gently clean around buttons. If damaged, contact support. |
User Tips
- For optimal performance, ensure the remote control is within the specified 60-meter range of the motor. While it can transmit through walls, heavy obstructions may reduce effective range.
- Keep the remote control away from moisture and direct heat sources to prevent damage.
- Consider using rechargeable AAA batteries for environmental friendliness and convenience.
Warranty and Support
For any issues not covered in this manual, or for technical support, please contact the seller or manufacturer directly. Keep your purchase receipt as proof of purchase for any warranty claims.
