HIRISI B1139

Contents

Hirisi Carp Fishing Bite Alarm

Model: B1139 (Also applicable to B1140 series)

Introduction

Thank you for choosing the Hirisi Carp Fishing Bite Alarm. This device is designed to enhance your fishing experience by providing clear audio and visual alerts when a fish bites. Featuring a waterproof design, snag bar, and a bright blue LED indicator, it's built for reliability in various fishing conditions. This manual provides essential information for safe operation, setup, maintenance, and troubleshooting.

Two Hirisi Carp Fishing Bite Alarms

Figure 1: Hirisi Carp Fishing Bite Alarms (2-piece set)

Safety & Warnings

Important Safety Information

Read all instructions before use. Failure to follow these instructions may result in damage to the product or personal injury.

  • Warning: Keep the device and its cord out of reach of children under 3 years old.
  • Keep away from children unless supervised by an adult.
  • Do not use this product for purposes other than its intended use.
  • Inspect the product before each use; do not use if damaged.
  • Follow installation and operation guidelines to avoid injury.
  • Do not expose to water or moisture beyond its intended waterproof rating.
  • Handle with care to avoid cuts or injuries.

Setup

1. Before First Use

  • Check the main unit and all accessories for damage.
  • Remove all packaging and protective materials.
  • Install one 9V battery (not included) into each alarm unit. Ensure correct polarity.

2. Device Installation

  1. Fix the alarm securely on your rod rest or bank stick using the standard 3/8 thread.
  2. Tighten the adjusting knob firmly to prevent movement.
  3. Route your fishing line and place it against the sensing contact (roller wheel) to ensure sensitive detection.
Bite alarm mounted on a fishing rod rest

Figure 2: Alarm mounted on a rod rest

3. Component Identification

Diagram of bite alarm with labeled parts

Figure 3: Key Components

  1. LED Light Band (8 LEDs)
  2. Night Light
  3. Tone Control Button (T/V)
  4. Volume Control Button (V/O)
  5. Sensitivity Control Button (S)
  6. 2.5mm Jack for Illuminated Swinger

Operating Instructions

1. Power On/Off

  • Press and hold the Volume Control button (V/O) to turn the unit ON or OFF.

2. Sensitivity Adjustment

  • Press the Sensitivity Control button (S) to cycle through sensitivity levels. Adjust according to fishing conditions and fish activity. Higher sensitivity detects smaller line movements.

3. Volume & Tone Setting

  • Press the Volume Control button (V/O) to adjust the alarm volume.
  • Press the Tone Control button (T/V) to change the alarm tone.

4. Night Light Function

  • The alarm features a dedicated night light for visibility in low-light conditions.

5. Fishing Operation

  1. After casting your line, tighten it and ensure it is properly in contact with the sensor roller.
  2. Wait for bites. The device will activate sound and light alarms (blue LED) once a fish pulls the line.
  3. The alarm provides different sounds for a drop back (line moving towards you) and a run (line moving away from you).
Close-up of blue LED light band

Figure 4: Blue LED Light Band in action

6. Fish Fighting

  • When the alarm goes off, lift the rod firmly to hook the fish.
  • Control the reel drag properly to prevent line breakage and fish escape.

Maintenance

1. After Use & Storage

  • Turn off the power of the alarm unit.
  • Wipe off any water, dirt, and debris from the device using a soft, dry cloth.
  • Ensure the waterproof rubber seals are clean and intact.
  • Store the product in a dry and cool place, away from direct sunlight and extreme temperatures.

2. Battery Care

  • The alarm features a low battery warning. Replace the 9V battery promptly when indicated.
  • Remove batteries if the device will not be used for an extended period to prevent leakage.

Troubleshooting

  • Alarm not sounding/lighting: Check if the unit is powered on. Ensure the 9V battery is fresh and correctly installed. Verify the fishing line is making proper contact with the sensor roller.
  • False alarms: Adjust the sensitivity setting (S button) to a lower level. Ensure the rod rest is stable and not subject to excessive movement from wind or other external factors.
  • Intermittent operation: Check battery connections. Ensure no debris is obstructing the sensor roller.
  • Water ingress: Although waterproof, ensure the battery compartment is securely closed. If water enters, remove the battery, dry the unit thoroughly, and check seals before further use.

Specifications

Product NameCarp Fishing Bite Alarm
ModelB1139 (Also B1140)
Batch/Serial NumberHRS202501081 (Example)
MaterialABS Plastic, Aluminum (Snag Bar)
TypeFish Bell/Alarm
Dimensions (Approx.)11cm (Height) x 5cm (Width)
LED IndicatorBlue LED Light Band
Power Source1 x 9V Battery (not included)
FeaturesWaterproof, Adjustable Sensitivity, Volume, Tone, Snag Bar, Night Light, Low Battery Warning, 2.5mm Jack for Swinger, Standard 3/8 Thread
Package Dimensions (Approx.)16cm (L) x 16cm (W) x 5cm (H)
Package Weight (Approx.)0.194 kg

User Tips

  • Battery Life: Always use fresh 9V batteries for optimal performance and reliability. Consider carrying spares.
  • Weather Resistance: These alarms are designed to be waterproof and perform well even in rainy conditions. Ensure battery compartments are sealed properly.
  • Sensitivity: Experiment with sensitivity settings based on the water conditions and the type of fish you are targeting. Lower sensitivity for strong currents or windy conditions, higher for subtle bites.
  • Line Contact: Always ensure your fishing line is correctly seated on the sensor roller for accurate bite detection.
  • Compatibility: These alarms are standalone units and do not typically connect to external pagers unless specifically designed for such integration.

Warranty & Support

For any warranty claims, technical support, or inquiries regarding your Hirisi Carp Fishing Bite Alarm, please contact your original seller or retailer. Please have your proof of purchase and product model information ready.

Manufacturer Information

Manufacturer: SUCCESS COURIER SL, CALLE RIO TORMES NUM. 1, PLANTA 1, DERECHA, OFICINA 3, Fuenlabrada, Madrid
Contact: successservice2@hotmail.com / +34-910602659

EU Authorized Representative: Ningbo hai ruisi outdoor products co., ltd, Room 309, building 1, no. 188, wanjin road, haishu district, ningbo city, zhejiang province
Contact: service@hirisi.com.cn

A PDF version of this manual may be available for download from the seller's product page or at this link.

© 2023 HIRISI. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.