1. Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your WINXU 36V 48V 350W 18A Sine Wave FOC Brushless Motor Drive Universal Controller. This controller is designed for electric bicycles, scooters, and motorcycles, offering efficient and smooth power delivery. Please read this manual thoroughly before use to ensure proper function and safety.
Image: WINXU FOC Sine Wave Brushless Controller with various connection wires.
2. Safety & Warnings
Read all instructions to prevent damage and ensure safe operation.
- Warning: Keep the device and its cord out of reach of children under 3 years old.
- Always disconnect the battery power supply before installing or servicing the controller. Working with power on can easily damage the equipment and pose a safety risk.
- Ensure all connections are secure and correctly polarized to prevent short circuits, overheating, and damage to the controller or other components.
3. Specifications
| Feature | Specification |
|---|---|
| Product Type | Controller |
| Brand Name | WINXU |
| Origin | Mainland China |
| Controller Type | Sine Wave FOC |
| Input Voltage | 36V / 48V |
| Output Power | 350W |
| Output Current | 18A |
| Motor Type | Brushless motor with hall |
| Speed Type | Phase angle speed (1 wire) |
| Model (PDF) | 250W, 350W |
| Batch Number (PDF) | 260215P-01 |
| Dimensions (L x W x H) | 140mm (5.5in) x 70mm (2.76in) x 35mm (1.38in) |
| Weight | 0.4 kg |
Image: Controller dimensions (approximate).
4. Installation & Wiring
4.1 Pre-use Preparation
Before installing the controller, always disconnect the battery power supply. Do not work with the power on, as it may easily damage the equipment.
4.2 Reading the Product Wiring Diagram
Before starting the installation, carefully review the wiring diagram below and fully understand the functions of all connectors.
Image: Detailed wiring diagram for the WinXu Tech Controller.
4.3 Connector Function Introduction and Installation Steps
- Motor Phase Wire: Connect the three thick phase wires (yellow, green, blue) from the controller to your motor, matching colors. Ensure a secure connection as these handle high current.
- Motor Hall Sensor: Connect the 5-wire Hall sensor. Red, yellow, and blue are Hall signal wires; red and black are working voltage cables. Connect according to color. If your motor has a 6-pin Hall sensor, ignore the white speed signal wire, as this controller obtains speed data from the motor's phase wires.
- LCD Speed Display: This is a universal LCD speed signal connector that outputs phase wire speed signals. Compatible with LCD throttles using this type of signal.
- Pointer Speed Display: This single purple wire is for 1-wire communication LCD displays. Connect it correctly if using such a display. (Note: The 350W controller may not have this feature).
- Alarm Power Supply: This connector powers the anti-theft alarm system and continuously outputs battery voltage, unaffected by the key lock's on/off state.
- Alarm: A 4-pin connector with three signal cables for the alarm signal controller: power lock, motor lock, and status signal. This is an unlimited speed connector; if your alarm system has a speed limit connector, you can ignore it.
- Power Lock: Connect your original bicycle's key lock switch to this connector.
- Throttle: For installing a Hall throttle (thumb or twist). It receives a signal voltage of 1.1-4.2V. Red and black are operating voltage, white is the Hall signal. Connect correctly.
- Low-Level Brake: This power-off braking system automatically cuts off motor power when the brake is applied. The black cable is negative, and the white cable is the brake signal. For 2-cable low-level brakes, connect correctly.
- High-Level Brake: Uses a single wire, connecting to the positive terminal of a 12V voltage converter as the brake signal. When the brake is applied, the switch closes, and the controller receives the brake signal, cutting off power. Some high-voltage scooters use high-level braking. (Note: The 350W controller may not have this feature).
- Battery (Power Input): This is the device's main power supply. Connect the positive and negative terminals correctly. Incorrect connection can cause short circuits, overheating, and damage. Connect the battery as the very last step and carefully check for any short circuits or incorrect connections in other components before connecting. Double-check polarity.
- Automatic Detection (Self-Learning Cable): This connector is used for motor matching. After initial installation, plug in this connector. Lift the motor hub in the air; the motor will start driving. If the motor drives in the opposite direction, disconnect and reconnect the connector to change the driving direction. Once the motor drives in the correct direction without vibration, disconnect the self-learning cable. You can then test ride normally.
5. Operating Instructions
- Cruise Function: This controller supports automatic cruise control. To activate, plug in the cruise connector. When the throttle is held at a fixed speed for 10 seconds, the controller will automatically lock the current speed and enter cruise mode. If you install a button for manual cruise, connect it to this connector; cruise mode will activate only when the button is pressed after accelerating.
- Reverse Function: Connect this connector to your reverse gear switch. When the switch is closed, the controller enters reverse mode, with a maximum speed of 70%. (Note: The 350W controller may not have this feature).
- Three-Speed Function: Connect this connector to a three-speed gear selection switch on your scooter. The low speed is 80%, medium speed is 100%, and high speed is 110%. The black wire is the negative terminal. If the gear switch is not connected, the controller defaults to medium speed. Shorting the black cable with the blue cable activates high speed. Shorting the black cable with the brown cable activates low speed.
6. Maintenance & Storage
- Cleaning: Turn off the device before cleaning. Use a soft, lint-free cloth to wipe the controller.
- Storage: Store the controller in a dry place at room temperature (15°C – 35°C).
- Long-term Storage: If the device will not be used for an extended period, charge the battery to 50% every 3 months to maintain battery health.
7. Troubleshooting
- Motor runs in opposite direction: If the motor drives in the wrong direction after using the automatic detection (self-learning) cable, disconnect and reconnect the self-learning cable to reverse the driving direction.
- Motor Hall Sensor damaged: If the motor hall sensor is damaged, the controller will automatically switch to square wave drive mode to ensure the motor operates normally.
- No power or erratic behavior: Double-check all wiring connections, especially the battery input, for correct polarity and secure fit. Ensure no short circuits are present.
- LCD Display Incompatibility: This controller is not compatible with S866, G51, SW900, TF-100, and other protocol 2 communication LCD displays. It supports phase speed measurement LCD displays and one-line communication LCDs or pointer speed meters. Verify your LCD display's compatibility.
8. User Tips
- Always confirm the compatibility of your LCD display with the controller before purchase or installation.
- For optimal performance in sine wave mode, ensure your motor's hall sensor is functioning correctly.
- When performing the automatic detection (self-learning) process, ensure the motor hub is lifted off the ground to allow free rotation.
9. Disposal & Recycling
This symbol indicates that this product should not be treated as household waste. According to the WEEE Directive (2012/19/EU), it must be disposed of at an appropriate electronic waste collection point for recycling to prevent potential negative consequences for the environment and human health.
10. Warranty & Support
For any questions, technical support, or warranty inquiries regarding your WINXU controller, please contact the seller or manufacturer directly. The manufacturer information is as follows:
- Manufacturer: ShenZhne Winxu Technology Co,.Ltd
- Address: No.118, Building B, Yongxing Office Building, No. 68, Tianyun Road, Songgang Street, Baoan District, Shenzhen, China
- E-mail: Winxutech@163.com
- Tel: +86-15814065441
An official PDF user manual is available for download here.