Welcome
Thank you for purchasing the Juson Audio FTA88 Mosfet Stereo Full Tube Amplifier. This amplifier has been designed to make it easy for anyone to enjoy the warm, natural sound quality of vacuum tube amplification without the size and power consumption. The FTA88 is a high-end MOSFET full tube amplifier, capable of achieving higher power without a high electronic current, as there is no need to pass through the output cattle. The output power can reach 90 watts*2@4 ohms in total, delivering strong and powerful bass, perfect middle, and clear treble. It is suitable for audiophiles who prefer to enjoy voices, symphony, rock, big dynamic, and a strong sense of momentum music.
Important Safety Instructions
CAUTION: RISK OF ELECTRIC SHOCK. DO NOT OPEN.
- To reduce the risk of electric shock, do not remove the cover. No user-serviceable parts inside. Refer servicing to qualified personnel.
- To reduce the risk of fire and shock, do not expose the unit to rain or moisture.
- The unit should be connected to an earth-grounded AC electrical socket.
- The unit should be operated in a well-ventilated area. Minimum clearance is 2 inches from the ventilation openings.
FCC Statement
- This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
What's In The Box
- FTA88 MOSFET/Single-ended Class A Full Tube Amplifier
- Remote Control
- AC Power Cable
- Bluetooth Antenna
- User Manual (PDF referenced in text)
Please check to make sure that nothing is missing from the package.
Packaging
The product is packaged with inner thicker foam for crash resistance, a gift box with corner protector, a 5-layer K&K outer box, and wrapped by films at the outside of the package to ensure safe delivery.
Setup and Connections
Connecting Power
Before connecting the main power cable, ensure that the voltage selector switch on the rear panel is set to match your local voltage (e.g., 115V for USA, 230V for EC). Incorrect voltage could cause damage to the amplifier and poses a potential risk of fire. When operating at 230V, the internal fuse located in the IEC socket should also be changed. In most 230V applications, a separate power cord will be required and is not included.
Connecting Speakers
The amplifier has 4Ω-8Ω speaker output options. Select the correct ports for your speakers first. Use high-quality two-conductor speaker cables to connect your speakers to the binding posts on the rear of the unit.
- Connect the FTA88's left speaker terminals marked "FL-" and "FL+" to the corresponding "-" and "+" terminals on your left speaker.
- Repeat the same process for the right channel.
Note: Never connect the negative terminals together. The FTA88 is not designed to operate in a bridged mode, and attempting to do so may damage the amplifier. The speaker outputs are not bridgeable. Please connect corresponding ports according to your speaker.
Connecting Banana Plug Cables
- Tighten the knob on the binding post.
- Insert the banana plug terminated cable into the end of the corresponding terminal.
Connecting Speaker Wires
- Strip about 3/8" (10mm) of insulation from the end of each speaker wire and twist the bare wires of the cable together.
- Unscrew the knob before inserting the bare wire into the hole in the side of each terminal.
- Tighten the knob to secure the wire.
Connecting Sources
The FTA88 is capable of receiving signals directly from a wide variety of sources. Using high-quality cables will ensure the best possible transmission from your connected devices.
Connecting Bluetooth Devices
- Connect the supplied Bluetooth antenna to the BT ANTENNA port on the rear of the unit.
- Ensure that the Bluetooth input is selected on the FTA88.
- Using a smartphone, tablet, computer, or other device capable of transmitting Bluetooth audio, go to the device's settings and scan for available Bluetooth devices.
- Look for and select "FTA88" in the device list and begin pairing.
- Once finished pairing, you can begin streaming your favorite music from up to 30 feet away.
The FTA88 uses Qualcomm QCC3095, supporting LDAC/aptX Lossless/aptX Adaptive/aptX HD/aptX/SBC/AAC/LC3 file formats.
Connecting a Turntable
The FTA88 is capable of connecting directly to most turntables without the addition of an external phono preamplifier.
- Ensure that your turntable is set to output a phono signal. Many modern turntables have the ability to output either a line-level signal or a phono signal. If your turntable is set to output a line-level signal, please connect it to the AUX input on the amplifier.
- Remove the covers from the PHONO RCA plugs and connect the turntable to the phono input.
- Connect the ground wire of the turntable to the ground terminal on the rear of the FTA88.
Connecting a Subwoofer
You can add a subwoofer using the SW OUT connection on the rear of the FTA88. This signal is full range and will send a mono summed signal that is controllable by the front volume knob. Using a single RCA cable, you can connect to the line-level input on a powered subwoofer or to any external subwoofer amplifier to power passive subwoofers.
Controls and Functions
Front Panel
- INPUT SELECTION: Turn this knob to select the desired source. Note: USB input will not be selectable unless a device is connected to the unit and powered on.
- METERS (VU Meter): Indicates the audio output level of the left and right channels.
- SOURCE INPUT SELECT INDICATOR: Indicates the input sources with a light.
- VOLUME CONTROL: Turn this knob to adjust the output volume.
- POWER SWITCH: Turns the device on or off. Note: To safeguard your devices, the amplifier will have approximately a 30-second turn-on delay.
Rear Panel
- PC-USB INPUT: Connect to a USB flash drive directly or other USB devices through a USB converter. The max capacity of the USB flash drive should be less than 128GB.
- ACTIVE SUBWOOFER OUTPUT (SW OUT): Use a single RCA cable to connect the SW OUT to a powered subwoofer or separate subwoofer amplifier. This will output a full-range mono signal, and the volume output will change depending on the position of the front panel volume control.
- BLUETOOTH ANTENNA: Connect the supplied Bluetooth antenna here for optimum signal strength.
- AUX INPUT: Standard RCA stereo input for line-level devices.
- PHONO INPUT: RCA stereo input for turntables with phono output.
- GROUND TERMINAL (GND): Connect the ground wire from your turntable here.
- COOLING FAN ON/OFF SWITCH: The cooling fan can be turned on when needed. We recommend turning it on when you select TF modes.
- SPEAKER OUTPUTS (4Ω-8Ω): Connect passive speakers here. Use insulated 2-conductor wire. Ensure polarity (+ and -) is consistent.
- DIGITAL (OPTICAL) INPUT: Optical digital audio input.
- DIGITAL (COAXIAL) INPUT: Coaxial digital audio input.
- NOISELESS COOLING FAN: Integrated cooling fan.
- AC POWER INPUT: Connect the AC power cable here.
- AC VOLTAGE SELECTOR SWITCH: Set to 115V or 230V according to your region.
Top Panel Controls
- MODES SWITCH (FET & TF): Turn this up or down by a tool at the same time to ensure it is in the same mode. When switching between Field Effect Transistor (FET) mode and Single-Ended (TF) mode, make sure there will be 30 seconds after turning off the power.
- PREAMP TUBES SWITCH: Turn this on the left or right side to change the preamp tubes. Preamp tubes 6N1/6N2/ECC85/6H1N could be switched to 12AX7/ECC83, but it should be done after power off.
Remote Control
- INPUT SELECTION: Directly select any of the inputs here. Note: USB is only selectable when a device is connected to the USB port on the rear of the unit.
- VOLUME + / -: Control the volume of the amplifier. The volume knob on the unit will rotate to indicate the current level.
- MUTE: Toggles MUTE ON/OFF.
- TRACK TRANSPORT CONTROLS: Control the playback of the USB Flash Drive input.
- Play/Pause: Start/pause the current song.
- Forward: Skip forward to the next song.
- Backward: Skip backward to the beginning of the current song or the previous song.
Note: Remote does not include battery; please prepare it yourself.
Operating Modes
The Juson Audio FTA88 tube amplifier features two distinct operating modes: MOSFET and Single-Ended (TF), offering flexibility for different listening preferences.
MOSFET Mode
FET mode is a Class A tube amplifier. The pre-amp and power-amp are both driven by vacuum tubes, and amplification output is done by dual MOSFETs (Metal-Oxide-Semiconductor Field-Effect Transistor). MOSFET working characteristics are similar to vacuum tubes. However, MOSFET has strong driving ability to get a high power which was driven directly by the vacuum tubes. In this working mode, the amplifier delivers strong and powerful bass, perfect alto, and clear treble. It is suitable for audiophiles who mainly listen to voices, symphony, rock, big dynamic, and a strong sense of momentum music. This feature ensures a smooth, highly stable, and distortion-free sound output, elevating your listening experience.
Single-Ended (TF) Mode
TF mode is a Single-Ended tube amplifier. The pre-amp and power-amp are both driven by vacuum tubes, but amplification output is done by a transformer. Limited by the transformer and vacuum tube capacity, the final power output is slightly smaller. Bass performance is not as good, alto performance is good, and sounds warmth, treble performance is normal. In conclusion, TF mode is more suitable for audiophiles who prefer to listen to voices. It embraces the warm, vintage sound characteristic of single-ended tube amplifiers, bringing a unique, nostalgic touch to your home audio system.
VMOS Working Principle
The principle of controlling the operating current of a field effect transistor is completely different from that of an ordinary transistor. It is much more simple than an ordinary transistor. The field effect tube just uses an external input signal to change the resistance of the semiconductor simply. In fact, it changes the size of the channel through which the operating current flows, and the transistor uses the signal voltage applied to the emitter junction to change the junction current flowing through the emitter junction, also includes extremely complex processes, such as minority carriers crossing the base region and then entering the collector region.
Field effect transistors not only have the advantages of ordinary transistors and electron tubes, but also have advantages that are lacking in both. The field effect transistor has bidirectional symmetry, that is, the source and drain of the field effect transistor are interchangeable (without damping). It is not easy for ordinary transistors to do this, however, it is simply impossible for electron tubes to reach this. The so-called two-way symmetry means that for ordinary transistors, the emitter and collector are interchanged, and for electron tubes, the cathode and anode are interchanged.
When an ordinary transistor is working, as the input end (emitter junction) is to forward biased, the input resistance is in very low voltage. When the input terminal of the field effect transistor (between feedback and source) is working, a negative bias or reverse bias can be applied. Positive bias can also be added. Therefore, the flexibility and diversity of circuit design are increased.
Usually when reverse bias is applied, its input resistance is higher, up to more than 100MΩ. This characteristic of the field effect transistor makes up for the shortcomings of ordinary transistors and electron tubes in some applications.
The radiation protection capability of field effect transistors is about 10 times higher than that of ordinary transistors.
Fast conversion rate and good high frequency characteristics.
Specifications
| Feature | Detail |
|---|---|
| Brand Name | JUSON AUDIO |
| Model Number | FTA88 |
| Channels | 3 (2.1) |
| Amplification | Class A |
| MOSFET | K1058 x2, J162 x 2 |
| MOSFET Power Output (Peak) | 90W RMS X2 @ 4 Ohm (THD≤5%) |
| Transformer Power Output | 10W RMS x 2 |
| Maximum Power Per Channel | 90 W |
| Input Sensitivity | 200mV |
| Frequency Response | 20-20,000Hz (±2dB) |
| Signal to Noise Ratio | >90 dB |
| Dynamic Range | >90 dB |
| Minimum Speaker Impedance | 4 Ohm |
| Channel Separation | 85dB |
| Preamplifier Tubes | 6H1N x 2 |
| Preamp Stabilivolt Tubes | ECF80 x 2 |
| Power-amp Tubes | KT88 x 2 |
| Power-amp Stabilivolt Tubes | WY-2 x 2, WY-3P x 1 (or 6Y9 x 2, 14BR11 x 1) |
| Bluetooth | Version 5.0 (Qualcomm QCC3095), supports aptX, aptX HD, aptX Low Latency, SBC, and AAC audio codecs |
| USB | Up to 48 kHz 16Bit |
| Digital Inputs | SPDIF LPCM (up to 48kHz 16Bit) |
| Inputs | CD, DVD, Optical, Coaxial, Bluetooth 5.0, USB, PHONO, AUX |
| Output | Passive Speakers, Active Subwoofer |
| Power Requirement | 220V, 50Hz/EC or 115V, 60Hz/USA (selectable) |
| Dimensions (W x D x H) | 380 x 370 x 206 mm (15 x 14-5/8 x 8-1/8 in.) |
| Product Weight | 14.8 kg (32.56 lbs.) |
| Certification | CE, FCC, RoHS |
| Origin | Mainland China |
All specifications are accurate at the time of printing. Juson Audio reserves the right to make improvements without notice.
Troubleshooting
| Problem | Cause | Solution |
|---|---|---|
| The unit fails to turn on | Power cable is not connected properly | Check to make sure both ends of the power cable are connected properly. |
| Incorrect voltage selection switch setting | Verify that the voltage selection switch is set according to the region and power standard in your country. | |
| Protection circuit has been activated | Turn the amplifier off and check that your speaker wires are not shorting out. If this problem persists, please contact Juson Audio for customer services support. | |
| The unit turns off suddenly | There is damage to the connected speaker cable that has exposed wire. | Examine the speaker wire for any damage. Do not use any cable that has exposed wire. |
| Speaker malfunctioning | Disconnect the speakers one at a time to see if the issue is caused by the speakers or the amplifier. If the problem persists with all speakers, please contact Juson Audio customer support. | |
| No sound | The output is muted | The amplifier can only be muted and unmuted from the provided remote. Press "Mute" on the remote control. If you cannot find the remote, turning the amplifier off and back on again will unmute the output. |
| Correct input has not been selected | Verify that the correct input is selected. | |
| Headphones are connected | Unplug the headphones from the front panel. Audio should resume in the connected speakers. | |
| Incorrect cable connections | Double check that the device you are trying to listen to is connected to the correct input. | |
| Low volume | Volume on the playback device is turned down | Verify that any volume control on your phone, computer, or connected playback device is turned up. |
| There is a "humming sound" | No ground connection from the amplifier to the turntable | Make sure that the GND connection is made between the turntable and the amplifier. |
| The turntable is distorted | The turntable is set to line output but is connected to the PHONO input. | Verify that if your turntable is using a line out signal that it is connected to the AUX input on the amplifier. If the turntable is outputting a phono signal, verify that it is connected to the PHONO input. |
| The phono connection is improperly grounded | Make sure that there is a connection between the grounding terminals on the amplifier and the turntable. | |
| Cannot connect by Bluetooth | There is another BT device connected to it | Disconnect the device and reset it by correct device. |
| Cannot work in USB | Did not have USB connector. | Prepare PC-USB cable and Female to female USB connector and insert U flash drive or computer in correct port. |
| The signal select is incorrect. | Select correct signal input by remote or physical button. | |
| Cannot work in Macbook | The Macbook's audio output setting is incorrect. | Change the Macbook's audio output setting by Amplifier. |
User Tips
- Tube Insertion: If the tube amplifier is not working, check if the tubes are in perfect condition and ensure they are inserted tightly. Crashes during transportation can sometimes loosen them.
- Voltage Stabilization Tubes: The WY-2 and WY3P tubes are used for voltage stabilization. It is normal for them to flicker if the voltage is not stable. This does not affect sound output, tube working life, or indicate a defective tube or amplifier.
- Remote Battery: The remote control does not include batteries. Please prepare them separately.
- Bluetooth Volume: If you experience low volume in Bluetooth input, check your device's Bluetooth settings. The Bluetooth audio output volume should follow your phone's speaker volume setting.
- Turntable Connection: This amplifier has a built-in phono preamp, allowing direct connection of a turntable to the PHONO input. Ensure your turntable is set to output a phono signal, not line-level, when using this input.
- Voltage Compatibility: The amplifier is compatible with both 115V (USA) and 230V (EC) power standards. Remember to correctly set the voltage selector switch on the rear panel to match your local power supply.
Warranty and Support
Juson Audio products are warranted to be free of defects for the whole unit for 2 YEARS and vacuum tubes for 1 YEAR from the date of purchase from an authorized Juson Audio dealer. This warranty and all rights provided are limited to the original owner and are non-transferable. Responsibility is limited to replacement or repair as set forth in this warranty.
Should a product require warranty service during this period, Juson Audio will repair or replace without charge, any part or product proving defective in material or workmanship. All warranty repairs and service must be performed by an authorized Juson Audio technician or service facility. The use of non-authorized repair services renders this warranty null and void, and any charges relating to non-authorized repair are the responsibility of the product owner.
All expenses (except return shipping costs) related to replacing or repairing a defective part or product under this warranty shall be assumed by Juson Audio. Juson Audio reserves the right to replace defective product with a new or factory reconditioned unit.
For any support, please contact Juson Audio:
- Phone: +86 755 89717080
- Email: support@juson-cn.com
- Website: juson-cn.com
Juson Audio provides 24 Months Quality Guarantee for the Whole Unit and 12 Months Quality Guarantee for Tubes. Lifetime Technical support is also provided.
Juson Audio aims to make the sound better and will focus on audio always. Make a deal, Enjoy lifetime services! Juson Audio's Team will do the best to provide the after-sales service as good as possible! Please feel free to contact us for any technical support!
User Manual PDF: For a detailed user manual, please refer to the official PDF document available from Juson Audio.
Product Overview Video
Official product overview and demonstration of the Juson Audio FTA88 amplifier.