XIEGU G106C/G106

Contents

XIEGU G106C/G106 HF Portable Transceiver User Manual

Model: G106C/G106

Introduction

The XIEGU G106 is a compact 5W portable QRP (low-power) HF transceiver featuring an SDR (Software Defined Radio) circuit structure. It utilizes 16-bit CODEC sampling for superior performance across SSB, CW, and AM modes. Additionally, it includes a WFM (88-108MHz) receiving function for local FM broadcasts. Equipped with a CW digital filter offering three bandwidths, the G106 enhances connectivity to distant stations. With an optional external DE-19 digital adapter, it supports FT8 communication via computer. This manual provides comprehensive instructions for setting up, operating, maintaining, and troubleshooting your G106C/G106 transceiver.

1. Setup

1.1 Product Unboxing and Package Contents

Before proceeding with setup, carefully unbox your transceiver and verify that all components are present and in good condition. The standard package includes:

  • G106 Host: 1 set
  • Standard Hand Microphone: 1 unit
  • Power Line: 1 piece
  • Instruction Manual: 1 copy
  • Warranty Card: 1 copy
  • Certificate of Conformity: 1 copy
XIEGU G106C/G106 Transceiver package contents including the radio, microphone, power cable, and manual.
Figure 1: Complete package contents of the XIEGU G106C/G106 HF Transceiver.

1.2 Antenna Installation

  1. Align the antenna with the ANT interface on the rear of the transceiver.
  2. Rotate the antenna clockwise to tighten it securely.
  3. Attention: When twisting the antenna, always hold the base of the antenna. Do not shake the top of the antenna to avoid damaging the internal wiring.
Rear view of XIEGU G106C/G106 Transceiver showing the ANT connector and other ports.
Figure 2: Rear panel of the G106 transceiver with the ANT connector visible.

1.3 External Power Supply Connection

The G106 transceiver operates on a DC input voltage of 9-15V. Use the provided power cable to connect to an appropriate power source.

  • Polarity: Carefully inspect the polarity of the power lines to avoid reverse polarity connection. Incorrect polarity can damage the transceiver.
  • Voltage: Ensure the external power supply provides a stable voltage within the 9-15V DC range. Damage caused by abnormal power voltage is not covered by warranty.
  • EMC Ferrite Bead: For optimal performance and to prevent interference, an EMC ferrite bead can be applied on the power lines. Install the ferrite bead as close as possible to the power plug. This helps prevent external disturbances from entering the radio and reduces radio-frequency interference radiating externally via power lines.
Diagram showing how to connect an external power supply to the XIEGU G106C/G106 transceiver, including the use of a ferrite bead.
Figure 3: External power supply connection diagram, illustrating the use of a ferrite bead for EMC.

2. Operating Instructions

2.1 Basic Operation

Power On/Off

  1. Power On: Short-press the power button to turn on the G106.
  2. Power Off: Long-press the power button for about 2 seconds to power off the G106 when it is in the power-on state.

Turn Off/On Screen Backlight (Power-on State)

  • Short-press the power button to turn off the backlight of the display.
  • Short-press the power button again to turn on the backlight of the display.
Diagram showing the power button location and other controls for basic operation of the XIEGU G106C/G106 transceiver.
Figure 4: Basic operation controls, including the power button.

2.2 Adjusting the Volume

  1. Turn the volume knob (left-most knob on the front panel) to the left or right to adjust the output volume.
  2. Short-press the volume knob to switch audio output between the built-in speaker and the hand microphone speaker.

2.3 Operating Frequency Band and Mode Selection

  1. Press the MODE button (located at the top of the transceiver) to switch between available operating modes (SSB, CW, AM, WFM).
  2. Use the BAND left (◀) and right (▶) buttons to cycle through the operating frequency bands in sequence: 1.8MHz → 3.5MHz → 7MHz → 10MHz → 14MHz → 18MHz → 21MHz → 24MHz → 28MHz.
Diagram showing the MODE button and BAND selection buttons on the XIEGU G106C/G106 transceiver.
Figure 5: Location of Volume, MODE, and BAND selection buttons.

2.4 Multi-function Menu Items

The G106 transceiver features a multi-page menu system to access various settings and functions. Below is a list of the menu items:

Table 1: Multi-function Menu Items
Menu PageV/MA/BMWMC
1/5Frequency/channel modeVFOA-VFOB switchingMemory channelErase memory channel
CWFCWTCWRQSK
2/5CW filter selectionCW sidetoneCW dot-to-dash ratioQSK switch
KSKMIMBCSN
3/5Automatic key rateKey modeIAMBIC modeStartup information settings
SPLDISBPVER
4/5Pilot frequency modeDisplay modeKeypad toneVersion information
WFM///
5/5FM receiver
Table of multi-function menu items for the XIEGU G106C/G106 transceiver.
Figure 6: Multi-function menu items for detailed configuration.

2.5 Advanced Features

2.5.1 One-Click Frequency Matching/Copying

Some G106 models may support a frequency duplication function to copy settings between two transceivers:

  1. Bring two G106 transceivers close together.
  2. On the Transmitter unit: Enter the menu and select "Copy" or "CLONE" mode.
  3. On the Receiver unit: Also enter replication mode.
  4. Press the PTT button on the Transmitter unit. The data will be automatically transmitted to the Receiver.

2.5.2 Scanning Function

If you are unsure which channel the other party is on, you can use the scanning function:

  • Press the SCAN button. The transceiver will automatically cycle through channels to detect signals.
  • Scanning will stop automatically when a signal is detected on a channel.

2.5.3 Voice Control (VOX) Function

After enabling the VOX (Voice Operated eXchange) function, you do not need to press the PTT button to transmit. You can directly speak into the microphone to emit, which is convenient when both hands are occupied.

2.6 How to Make a Call (Press-to-Speak Half Duplex)

The G106 transceiver operates in a "press and speak" half-duplex mode, meaning only one party can transmit at a time.

Transmission (Speech)

  1. Press and hold the PTT (Push To Talk) button on the side of the hand microphone.
  2. Hold the hand microphone vertically, with the microphone approximately 2.5-5 centimeters (1-2 inches) away from your mouth.
  3. Speak clearly at a normal pace.
  4. Release the PTT button after speaking to switch to reception mode.

Reception (Listening)

  • After releasing the PTT button, the transceiver automatically enters receiving mode.
  • You will hear the other person's speech through the speaker.

Communication Etiquette

  • Pause slightly before speaking to avoid interrupting.
  • After conveying key information, it is good practice to say "Done" or "Over" to inform the other party that you have finished speaking and can release the button.
Video 1: Demonstration of the XIEGU G106C/G106 transceiver in operation, showing power-on, frequency tuning, and microphone use.

3. Maintenance

3.1 Daily Cleaning

  • If the transceiver body becomes dirty, wipe it with a soft cloth dampened with a neutral detergent.
  • Do not use alcohol, spray, or strong detergents, as these can corrode the shell.

3.2 Storage

  • When not in use for a long time, turn off the transceiver.
  • Store the unit in a dry and cool place, away from direct sunlight and extreme temperatures.

3.3 Safety and Usage Precautions

  • Flammable/Explosive Environments: Do not replace batteries (if applicable) or operate the device in flammable and explosive places (e.g., gas stations, chemical plants), as electric sparks could cause explosions.
  • Continuous Transmission: Do not hold down the PTT button for extended periods (e.g., more than 1 minute). Continuous transmission can cause the unit to heat up and may damage the amplifier.
  • Antenna Handling: Do not hold the antenna or mobile transceiver by the antenna. This can lead to poor antenna contact or damage to internal components.

4. Troubleshooting

Refer to the table below for common issues and their possible solutions:

Table 2: Common Troubleshooting Guide
Problem PhenomenonPossible Causes and Solutions
Unable to power on
  • Power supply not connected or faulty.
  • Power button not pressed correctly.
Too close call distance/noise
  • Low power supply voltage (check power source).
  • Located in a dead corner of a building (try changing position).
  • Antenna not tightened (ensure secure connection).
The other party cannot hear my voice
  • PTT key not held down while speaking.
  • Microphone too far from the mouth.
  • Microphone faulty.

5. Specifications

Table 3: XIEGU G106C/G106 Technical Specifications
Receiving Frequency0.55~30MHz, 88~108MHz (WFM)
Transmitting Frequency3.5~3.9MHz, 7.0~7.2MHz, 10.1~10.15MHz, 14.0~14.35MHz, 18.068~18.168MHz, 21.0~21.45MHz, 24.89~24.99MHz, 28.0~29.7MHz
Operating ModeSSB/CW/AM, WFM (receive only)
Receiving SensitivityCW: 0.25uV @10dB S/N; SSB: 0.5uV @10dB S/N; AM: 10uV @10dB S/N
Frequency Stability±1.5ppm within 30min after power on; @25°C: 1ppm/hour
Transmitting Power≥5W @13.8V DC
Transmitting Spurious Suppression≥50dB
Audio Output Power0.3W
Operating Voltage9~15V DC
Standby Current0.37A @Max
Transmitting Current2.8A @Max
Dimensions (W*H*D)120*40*135 mm
WeightAbout 720g (host only)
MaterialPlastic
Waterproof / Water-ResistantNo
Is DisplayYes
Maximum Range10km-50km

Note: All specifications are typical and apply to amateur bands only. Specifications are subject to change without notice due to technical improvements. The operating frequency range may vary based on local regulations.

6. User Tips

  • Squelch Function: While not explicitly detailed in basic operations, most transceivers include a squelch function to suppress background noise when no signal is present. Refer to the multi-function menu (Table 1) or the full PDF manual for details on squelch settings if available.
  • Optimal Performance: For best receiving and transmitting performance, ensure your antenna is properly tuned for the operating frequency band.
  • FT8 Communication: To engage in FT8 digital mode communication, you will need the optional external DE-19 digital adapter to connect your G106 to a computer.

7. Warranty and Support

7.1 Warranty Policy

  • A 12-month warranty is offered for the main transceiver unit, starting from the date of receipt.
  • Accessories (such as the hand microphone and power line) are covered by a 6-month warranty.
  • The warranty does not cover damage caused by incorrect external power connection or abnormal power voltage.
  • For detailed warranty claims and procedures, please refer to the warranty card included in your package or contact your seller.

7.2 Further Assistance

If you encounter issues not covered in this manual or require further technical support, please contact the authorized dealer or XIEGU customer service. Please have your product model and serial number ready when seeking support.

A comprehensive user manual in PDF format is available for download. You can find it at: XIEGU G106 User Manual (PDF)

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.