FGHGF WiFi 6E Antenna 2T2R

Contents

FGHGF WiFi 6E Antenna 2T2R Instruction Manual

Model: WiFi 6E Antenna 2T2R

1. Introduction

The FGHGF WiFi 6E Antenna 2T2R is a high-quality, tri-band extension antenna designed to significantly improve the wireless performance of compatible motherboards and PCI-E wireless cards. Supporting 2.4GHz, 5GHz, and 6GHz frequency bands, this antenna provides enhanced signal reception and stability for your wireless network. Its magnetic base allows for flexible placement, ensuring optimal signal strength.

WiFi 6E Antenna with dual RP-SMA connectors and cable.

Figure 1: FGHGF WiFi 6E Antenna 2T2R

2. Specifications

Below are the technical specifications for the WiFi 6E Antenna 2T2R:

FeatureDetail
BrandFGHGF
ModelWiFi 6E Antenna 2T2R
Frequency Bands2.4GHz, 5GHz, 6GHz (Tri-band)
Connector TypeDual RP-SMA Male (Inner screw inner hole)
Cable Length80 cm
Standing Wave Ratio (SWR)1.5
GainNot specified (listed as "none" in product attributes)
MaterialPlastic
ColorBlack
Package Weight0.394 kg
Package Dimensions (L x W x H)16 cm x 4 cm x 3 cm
Diagram showing WiFi 6E antenna features including 2G/3G/4G/5G/WiFi6E, frequency 600-600mhz, standing wave 1.5, and RP-SMA connector detail.

Figure 2: Antenna specifications and connector detail

3. Compatibility

This antenna is designed for broad compatibility with various motherboards and wireless modules that feature two RP-SMA inner pin ports.

3.1 Compatible Motherboards

  • Asus ROG series: B560, B660, H610, H670, M13H, M12, M11, Z690, Z490, X570
  • Other motherboards with WIFI version from brands such as ASRock, Biostar, and Colorful, provided they have 2 SMA inner pin ports.

3.2 Compatible Wireless Modules

  • AX200, AX201, AX210, AX211
  • 3165, 3168, 3160AC
  • 7260, 7265
  • 8260, 8265
  • 9260, 9560, 9462AC

4. Setup Instructions

Follow these steps to install your WiFi 6E Antenna:

  1. Identify Ports: Locate the two RP-SMA inner pin ports on your compatible motherboard or PCI-E wireless card. These are typically found on the I/O shield of your motherboard or the bracket of your wireless card.
  2. Connect Antenna Cables: Carefully align the dual RP-SMA male connectors of the antenna with the corresponding ports on your device. Gently screw them in clockwise until they are finger-tight. Do not overtighten.
  3. Position Antenna: Place the antenna on a flat, stable surface. The magnetic base allows for flexible positioning on metallic surfaces, such as your PC case, for optimal signal reception.
  4. Adjust Orientation: The antenna can be adjusted to an upright or folded position. For best performance, orient the antenna vertically or in a position that maximizes signal strength to your wireless router.
WiFi 6E antenna in an upright, operational position.WiFi 6E antenna in a folded, compact position.

Figure 3: Antenna in upright and folded positions

5. Operating the Antenna

Once installed, the antenna operates passively to enhance your wireless signal. No additional software or drivers are required for the antenna itself. Ensure your motherboard's wireless card drivers are correctly installed and updated for optimal performance.

  • Signal Optimization: Experiment with different antenna orientations and placements to find the best signal strength for your environment.
  • Band Selection: The antenna supports 2.4GHz, 5GHz, and 6GHz bands. Your wireless card and router will automatically negotiate the best available band.

6. Maintenance

The WiFi 6E Antenna requires minimal maintenance:

  • Cleaning: Use a soft, dry cloth to gently wipe the antenna and cables. Avoid using liquid cleaners or abrasive materials.
  • Storage: If not in use, you can fold the antenna for compact storage. Store it in a cool, dry place away from direct sunlight and extreme temperatures.
  • Cable Care: Avoid sharply bending or kinking the antenna cables to prevent damage.

7. Troubleshooting

If you encounter issues with your WiFi 6E Antenna, consider the following:

  • No Signal / Weak Signal:
    • Ensure both RP-SMA connectors are securely attached to your wireless card/motherboard.
    • Try repositioning the antenna. Move it away from large metal objects or other electronic devices that might cause interference.
    • Verify that your wireless card drivers are up to date.
    • Check your router's settings and ensure it is broadcasting on the desired WiFi 6E (6GHz), WiFi 6 (5GHz), or WiFi 4/5 (2.4GHz) bands.
  • Antenna Does Not Fit:
    • Confirm that your motherboard or wireless card has RP-SMA inner pin ports. This antenna uses RP-SMA Male connectors.
    • Refer to the "Compatibility" section (Section 3) to ensure your hardware is supported.

8. User Tips

  • Verify Connector Type: Before purchasing, always double-check that your device requires RP-SMA inner pin connectors to ensure compatibility.
  • Optimal Placement: Utilize the magnetic base to place the antenna on top of your PC case or another elevated metallic surface for potentially better signal reception, especially if your PC is under a desk.
  • Driver Updates: While the antenna is passive, keeping your wireless card drivers updated is crucial for maximizing the benefits of WiFi 6E technology.

9. Warranty and Support

For any product-related inquiries, technical support, or warranty claims, please contact the seller or manufacturer directly. Keep your purchase receipt as proof of purchase.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.