ToolkitRC M6D V3

Contents

ToolkitRC M6D V3 Dual Channel Smart Charger User Manual

Model: M6D V3 | Brand: ToolkitRC

1. Introduction

Thank you for purchasing the ToolkitRC M6D multi-function charger. Please read this manual carefully before use to ensure the best experience with this product.

For news, information, and firmware updates, please visit www.toolkitrc.com.

2. Safety Information

⚠ WARNING: This product can expose you to chemicals including phthalates (DEHP), which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

  • The M6D requires an input voltage of 7-28V. Ensure the power supply voltage is within this range and connected with correct polarity.
  • Do not use this product in hot areas, near heat sources, or in damp, flammable, or explosive gas environments.
  • Only use this product under direct supervision. Do not leave charging batteries unattended.
  • When not in use, unplug the input power promptly.
  • When using the charging function, set the current to match the battery's specifications. Avoid excessive current charging to prevent battery damage.

3. M6D Layout and Components

Familiarize yourself with the various ports and controls of your M6D V3 charger.

Front layout of ToolkitRC M6D V3 charger with labels for Display, Scroll wheel, Exit key, CH key, Main port, Temp. Sensor Port, and Balance port.

Figure 3.1: Front View Layout

Back layout of ToolkitRC M6D V3 charger with labels for Input port, USB Output & upgrade, and Cooling fan.

Figure 3.2: Back View Layout

Detailed labeled diagram of M6D V3 ports including USB Port, Cooling Fan, CH1 Balance Port, CH1 Main Port, Exterm. Temp. Sensor, CH2 Main Port, CH2 Balance Port, Wheel Key, Channel & Exit Key, and Input.

Figure 3.3: Detailed Port Diagram

Controls:

  • Scroll Wheel: Turn left or right to navigate menus, press to confirm (OK).
  • CH.EXIT Key: Used to exit menus or switch channels.

Ports:

  • Input Port (DC 7-28V): Connect power supply.
  • Main Ports (CH1, CH2): Connect battery for charging/discharging.
  • Balance Ports (CH1, CH2): Connect balance lead for lithium batteries.
  • Temp. Sensor Port: For external temperature sensor.
  • USB Output & Upgrade (5.0V 2.1A): For charging mobile devices and firmware upgrades.
  • Cooling Fan: For heat dissipation.

4. Quick Start Guide

  1. Connect a 7-28V power supply or an input battery to the input port on the back of the M6D.
  2. The display will show the boot logo for 2 seconds, accompanied by a boot sound.
  3. After booting, the main interface will be displayed, showing charging status.
  4. Short press the [Exit] button to switch the cursor between the left and right channels.
  5. Press and hold [EXIT] to start testing the internal resistance of the corresponding channel. The internal resistance will be displayed after the test.
  6. Scroll the [Scroll Wheel] to switch between pages in the corresponding channel.
  7. Short press [OK] to select a charging task when the channel is idle, or to adjust/end work when the channel is active.
  8. Press and hold [OK] to enter the system settings interface when both channels are idle.
  9. Press [Exit] to end modifications or return to the previous interface.

Scroll Wheel Tips:

  • Short press [Scroll Wheel] once to confirm key functions.
  • Press and hold [Scroll Wheel] for 2 seconds to delete key functions.
  • A "di-di" prompt tone indicates successful key operation.
Quick start guide display example showing voltage, current, and internal resistance readings.

Figure 4.1: Quick Start Display

5. Operating Instructions

5.1 Charge and Discharge Settings

From the main interface, short press [OK] to enter the charging function menu.

Charge and discharge work display showing voltage, current, and battery cell information.

Figure 5.1: Charge and Discharge Work Interface

5.1.1 Battery Type Selection

Scroll the [Scroll Wheel] to move the cursor and select a stored battery type, or create a new one. Press [OK] to enter the battery setting interface.

  • Supported battery types: LiPo, LiHV, LiFe, Lion, NiMh, and PB.
Battery type selection menu showing LiPo, LiHV, LiFe, Lion, NiMh options.

Figure 5.2: Battery Type Selection

⚠ Warning:

  • Choosing the wrong battery type can damage the battery and charger, posing a risk of burning. Select carefully.
  • Do not use this product to charge batteries that do not indicate their type.

Battery Type Glossary:

  • LiPo: Lithium Polymer battery (Nominal: 3.70V, Fully Charged: 4.20V).
  • LiHV: High-Voltage Lithium battery (Nominal: 3.85V, Fully Charged: 4.35V).
  • LiFe: Iron-Lithium battery (Nominal: 3.30V, Fully Charged: 3.60V).
  • Lion: Lithium-Ion battery (Nominal: 3.60V, Fully Charged: 4.10V).
  • NiMh: Nickel-Metal Hydride battery (Nominal: 1.20V).
  • PB: Lead-Acid battery (Nominal: 2.00V).

5.1.2 Number of Cells

Move the cursor to [Battery cell Number] and press [OK] to modify the number of battery cells (e.g., 1S, 2S, 3S, 4S, 5S). Turn the [Scroll Wheel] to adjust the value.

  • When set to [Auto], the charger automatically recognizes the number of connected battery cells based on the output port voltage.
  • Short press [OK] and [Exit] to apply changes and return.

⚠ Important Tips:

  • Over-discharging or over-charging can lead to incorrect cell number recognition. Manually set the correct number.
  • Incorrect cell numbers can result in incomplete charging or battery damage. Set carefully.
  • For Lixx batteries, connecting the balance port allows for more accurate cell identification.

5.1.3 Mode Selection

Move the cursor to [Mode] and press [OK] to modify the working mode.

  • Available modes: Charge, DisCHG (Discharge), StoCHG (Storage Charge).
  • LiPo, LiHV, LiFe, Lion batteries support charge, discharge, and storage.
  • NiMh batteries support charge, discharge, and cycle.
  • PB batteries support charge and discharge.
Mode selection menu showing Charge, DisCHG, and StoCHG options.

Figure 5.3: Mode Selection

5.1.4 Discharge Mode (Inter/Recycle)

When Discharge, Storage, or Cycle mode is selected, the battery setting interface will show discharge mode options.

  • Inter (Internal) Mode: Discharges through internal heat consumption. Maximum support 3.0A@12W.
  • Recycle Mode: Recovers electrical energy from the discharging battery to the input battery (if the input is a suitable battery). Maximum support 15.0A@250W.
Discharge mode menu showing Inter and Recycle options.

Figure 5.4: Discharge Mode Selection

5.1.5 Input MaxVoltage (for Recycle Mode)

If Recycle mode is selected, the Input MaxVol setting will appear. Move the cursor to [Input MaxVol] and press [OK] to adjust. If the input voltage reaches this value during discharge, the discharge will stop.

⚠ Tip: Set the input cut-off voltage within the safe voltage range of your power supply battery. Setting a high over-voltage may damage the input power battery.

5.1.6 End Voltage (TVC)

Move the cursor to [End Voltage] and press [OK] to modify the end voltage of a single battery. This is the charging cut-off voltage. For discharge mode, it's the discharge cut-off voltage. Scroll the [Scroll Wheel] to adjust in 0.01V steps.

  • Only LiPo, LiHV, LiFe batteries can set the end voltage.
  • If unfamiliar with battery characteristics, do not modify the cut-off voltage.
  • Charging cut-off voltage can be set within ±50mV of full voltage.
  • TVC: Terminal Voltage Control.
End Voltage (TVC) setting menu showing voltage options like 4.18V, 4.19V, 4.20V, 4.21V, 4.22V.

Figure 5.5: End Voltage Setting

5.1.7 Current Setting

Move the cursor to [Charge Current] or [Discharge Current] and press [OK] to modify. Rotate the [Scroll Wheel] to adjust the value in 0.1A steps. Quickly scroll to increase/decrease rapidly.

  • Charger supports up to 15.0A (asynchronous mode).
  • In synchronous mode, maximum support is 25A.

⚠ Tip: Set the charging rate to 1-2C according to battery capacity. For a 2000mAh battery, set current to 2.0-4.0A.

Current setting menu showing current options like 9.8A, 9.9A, 10.0A, 10.1A, 10.2A.

Figure 5.6: Current Setting

5.1.8 NiMH Setting (PeakV)

For NiMh battery type, you can set the negative pressure value (PeakV) when the battery is fully charged. The range is 5mV-15mV.

  • Only NiMh batteries can set negative battery voltage.
  • PeakV: The voltage drop of each piece peaks when the nickel-metal hydride battery is fully charged.
NiMH PeakV setting menu showing options like 5mV, 6mV, 7mV, 8mV, 9mV.

Figure 5.7: NiMH PeakV Setting

5.1.9 Cycle Setting (for NiMh)

When NiMh battery type and Cycle mode are selected, the setting interface will show options for number of cycles and rest time.

  • Move cursor to [Cycle times] and press [OK] to set cycles (2-12).
  • Move cursor to [Rest time] and press [OK] to set interval (2-10 minutes).
Cycle times and Rest time settings menu.

Figure 5.8: Cycle and Rest Time Settings

5.2 Power Mode Setting

When "Power" is selected as the battery type, only Output Voltage and Max Current options are available.

  • Output Voltage: Adjustable from 1V to 28V.
  • Max Current: Adjustable from 0.5A to 15A.

5.3 Smart Battery Setting

When "Smart Battery" is selected, settings are limited to Drone Model and Max Current.

  • Select from various drone models (e.g., Mavic2, MavicS, Phantom, Inspire).
  • Set Max Current from 0.5A to 15A.
Smart battery settings menu showing drone models like Mavic2, MavicS, Phantom, Inspire.

Figure 5.9: Smart Battery Drone Model Selection

5.4 Synchronous Mode

Enable synchronization in the settings menu to allow two channels to charge the same battery with a total current of 25A. Refer to the diagram for connection.

Wiring diagram for synchronous mode charging, showing two channels connected to a single battery.

Figure 5.10: Synchronous Mode Connection

6. System Settings

Long-press [OK] on the main interface when both channels are idle to enter the system settings.

System settings setup menu showing options for Input power set, Charging security Set, Sync... mode, Continuous work, Work completed, and Backlight.

Figure 6.1: System Settings Menu

6.1 Input Power Settings

Enter relevant power supply settings. Long-press to select power supply 1, 2, or 3. Short press to expand settings.

  • Power Type: Battery or Adapter (PSU). Recycle mode is not compatible with PSU.
  • Max Power: Maximum power absorbed from the input port during charging (e.g., 560W).
  • Max Current: Maximum current drawn from the input port during charging (e.g., 30.0A).
  • Voltage Range: Allowable input voltage range (e.g., 7.0-28.0V).
Input power set menu showing Power type, Max power, Max current, and Voltage range.

Figure 6.2: Input Power Settings

6.2 Charging Security Settings

Short press to expand these settings.

  • Safe Inter. Temp.: Internal temperature limit (e.g., 80°C). Device stops output if exceeded.
  • Safe Exter. Temp.: External temperature limit (e.g., 60°C). Device stops output if external sensor detects higher temp.
  • Safe Time: Maximum continuous charge/discharge time (e.g., 200 Min). Device stops if exceeded.
  • Safe Capacity: Maximum continuous charge/discharge capacity (e.g., 30Ah). Device stops if exceeded.

6.3 Other System Options

  • Synchronization Mode: Can be enabled/disabled. When enabled, both channels work synchronously for more power.
  • Continuous Work: If selected, the charger automatically continues with the same settings on the next connected battery after one is completed. Ensure the next battery matches the previous one's settings.
  • Work Completed: Choose whether to stop or trickle charge after completion.
  • Backlight: Adjust backlight brightness from 1 to 10 levels.
  • Buzzer: Set the buzzer tone to on or off.
  • Language: Select system display language (English, Chinese, etc.).
  • Default: Restore all settings to factory defaults.

7. Other Functions

7.1 Firmware Upgrade

Connect the M6D to a computer using the provided USB cable. The computer will recognize it as a USB disk named "Toolkit". Download the app.upg upgrade file from the official ToolkitRC website, then copy and paste it to overwrite the existing files on the USB disk. The firmware will then be upgraded.

7.2 USB 5.0V Output

The USB interface can output 2.0A current at 5.0V, allowing you to charge mobile devices.

Integrated USB 2.1Amp Interface diagram showing mobile phone charging and firmware upgrade via PC.

Figure 7.1: USB Output and Firmware Upgrade

7.3 Automatic Continuous Charge and Discharge

When a battery is fully charged, unplug it for 2 seconds, then connect the next battery. The device will automatically continue charging or discharging according to the set "Continuous work mode" (if enabled in system settings).

7.4 Fan Operation

  • If the internal temperature exceeds 45°C, the fan will operate at half-speed to reduce noise.
  • If the internal temperature exceeds 53°C, the fan will operate at full-speed to enhance heat dissipation.
Optimized Heat Dissipation diagram showing honeycomb air vents and cooling fan operation.

Figure 7.2: Optimized Heat Dissipation

7.5 Manual Voltage Calibration

In the shutdown state, press and hold the [Scroll Wheel] while connecting the power supply. The system will enter manual voltage calibration mode. Measure the actual voltage of each battery with a voltmeter, then move the cursor to the corresponding voltage value on the charger's display and modify it to match the voltmeter reading. After calibration, move the cursor to save, short press once, and the buzzer will beep to confirm successful save. Then log out or shut down.

7.6 Fully Charged Indication

When a lithium battery is charged, the display will prompt "Fast charging has ended". If the battery is not removed, constant voltage trickle charging will automatically commence to ensure the battery is more fully charged.

8. Specifications

FeatureDetail
Input Voltage7-28V @ MAX30A
Battery Type SupportedLiPo, LiHV, LiFe, Lion (1-6S), NiMh (1-16S), Pb (1-10S)
Balance Current800mA @ 2-6S
Voltage Accuracy<0.005V
Charging Power (Asynchronous)0.1-15A @ 250W *2
Charging Power (Synchronous)0.1-25A @ 500W
Discharging Power (Recycle Mode)0.1-15A @ 250W *2
Discharging Power (Normal Mode)0.1-3A @ 12W *2
USB Output2.1A @ 5V (Upgrade @ USB3.0)
Battery Voltage Range1.0V-5.0V @ 1-6S
Battery Internal Resistance1-100mR @ 1-6S
DisplayIPS 2.4 inch 320*240 resolution
Product Size98mm * 68mm * 35mm
Product Weight220g
Individual Packing Size108.5mm * 80.5mm * 46mm
Individual Packing Weight300g
Product description and features list.

Figure 8.1: Product Features Overview

Quality IPS Display with wide viewing angle.

Figure 8.2: Quality IPS Display

Diagram showing dual 250W 15Amp channels (asynchronous) and one 500W 25Amp channel (synchronous).

Figure 8.3: Dual Channel Power Capabilities

Power comparison graph between M6D (500W/25A) and M8 (300W/15A).

Figure 8.4: Power Comparison (M6D vs M8)

9. User Tips

  • The M6D V3 charger supports multiple languages. If you require a specific language manual, please check the official ToolkitRC website or the system settings for language options.
  • Always ensure proper ventilation around the charger, especially during high-power operations, to allow the cooling fan to work effectively.
  • For optimal battery health, always use the balance port when charging lithium-based batteries (LiPo, LiHV, LiFe, Lion).

10. Troubleshooting

  • Charger not powering on: Ensure the input power supply is within the 7-28V range and connected with correct polarity.
  • Charging error/abnormality: Supervise charging/discharging closely. If an error occurs, a prompt box will appear with a tone. Check battery connections, battery type settings, and current settings.
  • Overheating: The charger has an optimized heat dissipation system with a cooling fan. If the internal temperature exceeds 45°C, the fan will activate. Ensure air vents are not blocked.
  • Incorrect cell count detection: For Lixx batteries, ensure the balance port is connected. If still incorrect, manually set the cell number.
  • Firmware update issues: Ensure the app.upg file is from the official website and correctly copied to the "Toolkit" USB disk.

11. Warranty and Support

For warranty information, technical support, or further assistance, please visit the official ToolkitRC website at www.toolkitrc.com. You may also refer to the official user manual PDF for comprehensive details: ToolkitRC M6D User Manual (PDF).

12. Product Overview Video

Video: ToolkitRC M6D V3 Charger Product Overview

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.