1. Introduction
The Infitary Motorcycle TPMS (Tire Pressure Monitoring System) is designed to enhance riding safety by providing real-time monitoring of your motorcycle's tire pressure and temperature. This wireless system features an LCD display that shows individual tire data, alerting you to potential issues such as tire leakage, high/low pressure, and high temperature. This manual provides detailed instructions for installation, operation, maintenance, and troubleshooting to ensure optimal performance and safety.
2. Package Contents
Please check the package for the following items:
- 1 x Monitor
- 2 x External Sensors (Front and Rear)
- 1 x Holder for monitor installation
- 1 x USB Power Line for charging
- 2 x Battery Keys (for sensor battery replacement)
- 2 x Anto-proof Nuts
- 1 x Spanner

3. Product Overview
3.1 Monitor Display Introduction
The monitor features a clear LCD display with different colors indicating various parameters for easy readability:
- Yellow Number: Time
- White Number: Tire Pressure
- Yellow Number: Tire Temperature


4. Installation
4.1 Monitor Installation
The monitor features a wireless design and a convenient holder for easy installation on your motorcycle's handlebar.
- Install the holder on the right side of the handlebar.
- The holder can be adjusted for handlebar diameters:
- 16-22mm: Use with all silicone inserts.
- 22-26mm: Use without the middle silicone insert.
- 26-30mm: Use without any silicone inserts.
- Secure the monitor to the holder.


4.2 External Sensor Installation
- Clock-wise turn the anti-remove nut onto the tire valve nozzle.
- Tightly turn the sensor onto the nozzle.
- Anti-clockwise turn the anti-remove nut to close to the sensor.
- Turn the nut close to the sensor with the provided spanner to secure it.

5. Operating Instructions
The monitor features two buttons: "-" (minus) and "+" (plus) for navigation and setting adjustments.
5.1 Power On/Off Monitor
- To Turn On: Press and hold the "-" button for 3-6 seconds.
- To Turn Off: Press and hold the "-" button for 3-6 seconds.
5.2 Time Setting
- Press both "-" and "+" buttons simultaneously and hold for 3 seconds to enter time setting mode.
- When "AM" is flashing, press "-" to select AM, PM, or 24hr mode (24hr mode is blank).
- Press "+" to set the hour, and "-" to adjust the value.
- Press "+" again to set the minutes, and "-" to adjust the value.
- Press both "-" and "+" buttons again to save and exit the setting.
5.3 Temperature Unit Setting
- Press the "+" button until a beep is heard to enter setting mode.
- Press the "-" button twice to set the unit of temperature.
- Press "+" button once, the temperature unit will flash.
- Press "-" button to select the desired unit (°C or °F).
- Press "+" button to save.
- Press and hold the "+" button for 3 seconds to exit the setting.
5.4 Pressure Unit Setting
- Press the "+" button until a beep is heard to enter setting mode.
- Press the "+" button once, and the unit will flash.
- Press "-" button to select the desired unit (BAR or PSI).
- Press "+" button to save.
- Press and hold the "+" button for 3 seconds to exit the setting.
5.5 Rear Tyre Pressure Alarm Setting
- Press the "+" button until a beep is heard to enter setting mode.
- Press the "-" button three times to enter 2P (Rear Tyre) pressure setting.
- Press the "+" button once, and the value will flash.
- Press "-" to set the desired value.
- Press "+" to save.
- Press and hold the "+" button for 3 seconds to save and exit.
5.6 Front Tyre Pressure Alarm Setting
- Press the "+" button until a beep is heard to enter setting mode.
- Press the "-" button twice to enter 1P (Front Tyre) pressure setting.
- Press the "+" button once, and the value will flash.
- Press "-" to set the desired value.
- Press "+" to save.
- Press and hold the "+" button for 3 seconds to save and exit.
5.7 High Temperature Alarm Setting
- Press and hold the "+" button until a beep is heard to enter setting mode.
- Press the "-" button four times to enter tire temperature alarm setting.
- Press "+" button once, and the digit will flash.
- Press "-" to set the desired value.
- Press "+" to save.
- Press and hold the "+" button for 3 seconds to exit the setting.
5.8 Tyre Identification (Pairing)
When replacing a sensor or display, re-recognition and matching are required. If changing a new display, both tires need to be re-recognized and matched. If changing a new sensor, only the new sensor needs to be re-recognized and matched.
- Press the "+" button 5 times to enter identification mode.
- Press "-" to select the front or rear tire. When selected, "---" will flash.
- Charge or discharge the tire (external type only needs to remove or install it).
- When the display makes a beep sound, the identification is successful.
- Press "-" to select the other tire and follow the same steps.
- Press and hold the "+" button until a beep is heard to save and exit the setting.
6. Alarms and Warnings
The system provides visual and audible alarms for various tire conditions. The red part of the display indicates an alarm prompt.
- High Pressure Alarm: When tire pressure exceeds the set high limit.
- Low Pressure Alarm: When tire pressure falls below the set low limit.
- High Temperature Alarm: When tire temperature exceeds the set limit.
- Air Leakage Alarm: Detected when there's a rapid drop in tire pressure. The corresponding tire pressure data will flash and warn. Press any button to stop the alarm.
- Low Voltage Alarm: Indicates low battery for the monitor.
- Power Alarm: Indicates low battery for the sensors. The alarm icon and figure of the corresponding tire will flash, and 'LO' will alternate with the figure.
- Failure Alarm: If a sensor is damaged or its battery fails, the display will show '---' for the corresponding tire. An alarm will sound every 5 minutes.

Note: The default pressure alarm value is 2.4 Bar. High pressure alarm value is typically set at ≥ standard pressure x 125%, and low pressure alarm at ≤ standard pressure x 75%. Temperature alarm is set at ≥ 80°C.
7. Maintenance
7.1 Charging the Monitor
The monitor has a built-in lithium battery and is charged via the provided USB power line. The charging port features an adsorption function for safe and convenient charging. A full charge takes approximately one hour and allows for normal use in any climate.

7.2 External Sensor Battery Replacement
The sensors use replaceable CR1632 button batteries. Do not dismantle the sensor unless necessary.
- Remove the anti-remove washer.
- Fit the provided tool into the rim of the sensor.
- Turn the tool to loosen the sensor case.
- Take the core out of the case.
- Replace the CR1632 battery with a new one.
- Reverse the above steps to reassemble the sensor.

8. Troubleshooting
- No Display/Monitor Not Turning On: Ensure the monitor is charged. Press and hold the "-" button for 3-6 seconds to power on. If still unresponsive, try pressing the boot key or set key button with force.
- Sensors Not Displaying Data ('---'): This indicates a sensor is damaged or its battery has failed. Replace the sensor battery or the sensor itself. Re-pair the sensor if replaced.
- Inaccurate Readings: Ensure sensors are correctly installed and tightened. Verify the pressure unit setting (BAR/PSI) and temperature unit setting (°C/°F) are correct.
- Charging Cable/Connectors Getting Hot: While some warmth during charging is normal, excessive heat (burning sensation) is not. Discontinue use immediately and contact customer support.
- Difficulty with Settings: Refer to the operating instructions (Section 5) and the provided video for detailed steps. Some users find watching a video helpful for setup.
- Holder Cracking: The provided holder is plastic. If it cracks, consider acquiring a more sturdy, possibly metal, holder for better durability.
9. Specifications
9.1 Sensor Specifications
| Parameter | Value |
|---|---|
| Operating Frequency | 433.92MHz ± 15MHz |
| Operating Voltage | 2.1-3.3V |
| Operating Temperature | -40°C to +105°C |
| Pressure Range | 0-8Bar / 0-116PSI |
| Sensor Size | 23mm x 15mm (WF) |
| Battery Capacity | 120mAh |
| Standby Current | 1µA |
| Working Current | 15mA |
| Humidity | 100% |
9.2 Display Specifications
| Parameter | Value |
|---|---|
| Operating Frequency | 433.92±15MHz |
| Battery Type | Built-in lithium battery, USB power line for charging. CR1632 button battery can be replaced. |
| Display Size | 48mm x 48mm x 27mm |
10. User Tips
- Initial Readings: You may need to move the bike a bit for the TPMS to get the initial pressure readings right after installation.
- Regular Checks: Always check your tire PSI weekly at the least, especially for e-scooters with tubed tires, to prevent flats.
- Setting Adjustments: While initial setup can be a bit challenging, it is achievable. Refer to the instruction video for visual guidance.
- Pre-Paired Sensors: The device usually comes pre-paired with the two sensors, simplifying initial setup.
- Holder Durability: The included plastic holder might not withstand prolonged use or vibrations. Consider upgrading to a more sturdy, possibly metal, holder for increased durability.
- Charging Cable: The charging cable is specific to the device. Keep it safe to avoid loss, as it may not be a universal type.
11. Frequently Asked Questions (FAQ)
- Q: How do I set the lower pressure alarm limit?
- A: To set the lower pressure alarm, enter the pressure alarm setting mode (Section 5.5 for rear, 5.6 for front). Use the "-" button to adjust the value to your desired lower limit, then press "+" to save. The system typically sets the low alarm at 75% of the standard pressure.
- Q: What type of connector is used to charge this device?
- A: The device uses a specific USB power line with a magnetic adsorption charging port. It is not a universal USB-C or Micro-USB connector.
- Q: What is the maximum range of the TPMS?
- A: The sensors transmit wirelessly to the monitor. The effective range is typically within the confines of a motorcycle, ensuring reliable communication between the tire sensors and the handlebar-mounted display.
- Q: Is it normal for the charging cable and connectors to get very hot during charging?
- A: While some warmth during charging is normal, excessive heat (to the point of burning) is not. If this occurs, immediately disconnect the charger and contact customer support. This could indicate a fault with the cable, charger, or device.
12. Warranty and Support
For any issues, questions, or warranty claims, please contact the seller or manufacturer directly. Keep your purchase receipt as proof of purchase.
13. Important Safety Notes
- This product is applicable to motorcycle tire pressure within 116 PSI (12V battery).
- Tire safety cannot rely solely on this product; regular tire examination is crucial. Ensure no holes, cuts, or bumps on your tires.
- If a warming sound is heard, stop the motor to check and fix the malfunction.
- The product cannot predict unexpected emergency tire bursts.
- Do not operate the device while riding.
- Battery life is related to riding distance.
