MicroZone C7-MINI

Contents

MicroZone C7-MINI RC Transmitter & MC8RE-V2 Receiver User Manual

Model: C7-MINI | Brand: MicroZone

Introduction

The MicroZone C7-MINI is a compact and versatile 2.4Ghz 8-channel RC transmitter designed for a wide range of remote-controlled models, including fixed-wing aircraft, cars, boats, multi-axis drones, lawn mowers, and intelligent agricultural machinery. This manual provides essential information for setting up, operating, and maintaining your C7-MINI transmitter and its compatible MC8RE-V2 receiver to ensure safe and optimal performance.

Video: MicroZone C7-MINI Product Overview

Safety Information

  • Always operate your RC model in open areas, away from people, vehicles, and obstacles.
  • Ensure all batteries are fully charged and properly installed before each use.
  • Never operate your RC model near power lines, busy roads, or residential areas.
  • Keep the transmitter and receiver away from moisture and extreme temperatures.
  • Perform a range check before each flight/operation to ensure proper signal reception.
  • Always turn on the transmitter first, then the receiver. When finished, turn off the receiver first, then the transmitter.
  • Do not modify the transmitter or receiver, as this may void your warranty and compromise safety.

Package Contents

Please check the package contents upon receipt:

  • MicroZone C7-MINI 2.4Ghz 8CH RC Transmitter
  • MicroZone MC8RE-V2 PWM/SBUS Receiver
  • Lanyard (may vary by package)
  • (Batteries are not included)
MicroZone C7-MINI transmitter with MC8RE-V2 receiver and lanyard

Image: C7-MINI Transmitter with MC8RE-V2 Receiver and Lanyard

Specifications

C7-MINI Transmitter

Feature Specification
ColorOff-white
DisplayBlack and white 128*64
LanguageChinese/English
Number of Channels8
ApplicationsFixed-wing, Car, Boat, Multi-axis, Lawn mower, Intelligent agricultural machinery
Control Range>800m
Frequency Range2401-2478MHz
Rocker Dynamic Range80%-120%
Fine-tuning MethodElectronic fine-tuning
Transmitter Power≤100mw
Input VoltageDC4.5-9V
Modulation ModeFSK
Power Supply Requirements4 x AAA batteries or 2S lithium battery
Low Voltage AlarmYes
Analog Picking (PPM)Yes
Runaway Protection SettingsSupport
Supported ReceiversMC8RE-V2, MC9002, MC6RE-V2, MC7RB-V2, MC3RB, MC4RB, MC6RE, MC7RB, MC8RE, E6R-R, M-BUS
Dimensions160*80*165mm
Weight470g

MC8RE-V2 Receiver

Feature Specification
ColorTeal transparent
ApplicationFixed wing, multi-axle, car, boat
Channel Output7 PWM signals, 1 SBUS signal, 1 external voltage input
Frequency Band2401MHz-2478MHz
Receiving Distance>1000m
Receiver Supply VoltageDC 4.5-6V
Voltage ReturnSupport
SBUS SignalSupport
Frequency Pairing ModeContact to frequency
Recovery PerformanceFast signal recovery
Runaway Protection SettingSupport
Supported Remote ControlC7-mini, 8B-mini, classic-10
Antenna TypeExternal dual antenna
Antenna Length150mm
Dimensions (L, W, H)46*25*14mm
Weight10g
Diagram showing battery compartment upgrade options and size comparison between C7-MINI and original MC7

Image: Battery Compartment Upgrade and Size Comparison

Setup

1. Transmitter Battery Installation

  1. Open the battery compartment cover on the back of the C7-MINI transmitter.
  2. Insert 4 x AAA batteries or connect a 2S lithium battery to the balance port. Ensure correct polarity if using AAA batteries.
  3. Close the battery compartment cover securely.
Back view of the C7-MINI transmitter showing the battery compartment

Image: Rear view of C7-MINI Transmitter with battery compartment

2. Receiver Connection (MC8RE-V2)

The MC8RE-V2 receiver provides 7 PWM signals, 1 SBUS signal, and 1 external voltage input. Connect your servos, ESCs, and other components to the appropriate ports on the receiver.

  • PWM Signals: Connect individual servos or ESCs to channels 1-7.
  • SBUS Signal: For compatible flight controllers or devices, connect to the SBUS port.
  • External Voltage Input: For voltage return functionality, connect an external voltage source (recommended within 6S) to the designated input.
Wiring diagram for the MC8RE-V2 receiver, showing 8 PWM signals, SBUS, and external voltage input

Image: MC8RE-V2 Receiver Wiring Diagram

3. Binding/Frequency Pairing

To establish communication between the C7-MINI transmitter and the MC8RE-V2 receiver, follow the binding procedure (contact to frequency mode). Refer to the receiver's specific instructions for detailed steps, typically involving pressing a bind button on the receiver while powering it on, then powering on the transmitter in bind mode.

4. Language Setting

The transmitter supports both Chinese and English languages. To change the language, navigate through the system settings menu on the transmitter's display. Look for a 'Language' or 'SYS Setting' option to switch between Chinese and English.

Transmitter display showing options for Chinese and English language settings

Image: Language Setting Display

Operating Instructions

1. Transmitter Controls Overview

Familiarize yourself with the various controls on your C7-MINI transmitter:

Labeled diagram of the C7-MINI remote control, showing sticks, switches, trims, and buttons

Image: Remote Control Function Analysis

  • Rocker Sticks: Control primary movements (e.g., throttle, aileron, elevator, rudder). Available in Mode1 (Right Hand) and Mode2 (Left Hand) configurations.
  • SW-A, SW-B, SW-C, SW-D: Various switches for auxiliary functions (e.g., gear, flaps, flight modes).
  • Trims: Fine-tune the neutral position of control surfaces (Throttle Trim, Elevator Trim, Aileron Trim).
  • MENU/OK Key: Access and confirm menu selections.
  • EXIT Key: Exit menus or go back.
  • MONITOR Key: Access channel monitoring display.
  • Up/Down Keys: Navigate menu options.
  • Lock Key: Prevents accidental changes to settings.
  • Power Switch: Turns the transmitter on/off.
  • Audio Interface: For computer connection (e.g., simulator dongle).
  • External Input DC6V Power Supply: For indoor testing.

2. Display Information

The backlit display shows critical information such as battery voltage (Bat), receiver voltage (Rx), and channel outputs. The display is designed to be readable even in direct sunlight.

C7-MINI transmitter being used outdoors with a clear, backlit display visible in sunlight

Image: Backlit Display in Sunlight

3. Simulation Training

You can connect the C7-MINI remote controller to a computer for simulation training. This allows you to practice flying or driving your RC model without the risk of damage. Use the audio interface port for connection to a simulator dongle.

Image depicting simulation training with the remote controller connected to a computer

Image: Simulation Training Setup

4. Runaway Protection

The runaway protection feature is crucial for safety. If the receiver loses signal from the transmitter (e.g., due to distance or transmitter being turned off), it will automatically move control surfaces to a pre-set safe position to prevent the model from flying or driving away uncontrollably. Ensure you set your runaway protection values correctly in the system settings.

Transmitter display showing runaway protection settings with channel values

Image: Runaway Protection Display

5. Travel Setting

Travel setting allows you to limit the range of movement for each control surface (e.g., rudder, aileron). This ensures that your control surfaces only move within the desired range, preventing over-control or mechanical binding.

Transmitter display showing travel settings for multiple channels

Image: Travel Setting Display

6. Speed Lock (for Car/Boat Mode)

In car or boat mode, the speed lock function can be activated. Once engaged, the model will maintain a constant speed without requiring continuous throttle input, useful for specific maneuvers or steady cruising.

Transmitter display showing 'Open' and 'Close' options for Speed Lock

Image: Speed Lock Display

7. Key Lock

The key lock feature prevents accidental changes to settings or unintended commands by disabling the transmitter's keys. This is useful during transport or when handing the transmitter to someone else.

Transmitter display showing 'System Settings' and 'Model Settings' with a lock icon, indicating Key Lock is active

Image: Key Lock Display

Maintenance

  • Keep the transmitter and receiver clean and free from dust and debris. Use a soft, dry cloth for cleaning.
  • Store the equipment in a cool, dry place, away from direct sunlight and extreme temperatures.
  • Remove batteries from the transmitter if it will not be used for an extended period to prevent leakage.
  • Regularly check all switches, sticks, and buttons for proper function and smooth movement.
  • Inspect receiver antennas for any damage before each use.

Troubleshooting

  • Transmitter not powering on: Check battery installation and ensure the power cable to the board is securely connected. Verify batteries are charged.
  • Receiver not responding: Ensure the transmitter and receiver are properly bound. Check receiver power supply and connections to the flight controller/servos.
  • Control stick not returning to center: This may indicate a missing or dislodged spring inside the stick mechanism. Disassembly and repair by an experienced technician may be required.
  • Broken switch: Damaged switches may require replacement. Avoid excessive force when operating switches.
  • Intermittent signal loss: Ensure receiver antennas are properly positioned and not obstructed. Check for sources of interference in the operating area.

User Tips

  • Language Change: If the display is in Chinese, navigate through the menu options to find the 'Language' or 'SYS Setting' to switch to English. This is a common initial setup step.
  • Manual Availability: While a physical manual might not be included, digital versions are often available on the official manufacturer's website.
  • Car Compatibility: The C7-MINI is compatible with cars, and its sticks can be configured for various control modes, including options to lock sticks in certain channels if supported by the model settings.
  • Initial Inspection: Upon receiving the product, carefully inspect all components, especially switches and control sticks, for any signs of damage or disconnected wires.

Warranty and Support

For warranty claims, technical support, or service inquiries, please contact the seller or the official MicroZone support channels. Keep your purchase receipt as proof of purchase.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.