Geberit Impuls 250 Dual Button Flush Valve

Contents

Geberit Impuls 250 Dual Button Flush Valve Instruction Manual

Model: Toilet Push Button

Introduction

This manual provides instructions for the installation, operation, and maintenance of the replacement dual flush button for Geberit Impuls 250 flush valves. Please read these instructions carefully before proceeding with installation or use to ensure proper function and longevity of the product.

Safety Information

Always exercise caution when working with plumbing fixtures. Ensure the water supply to the toilet is turned off before attempting any installation or maintenance. If you are unsure about any step, consult a qualified plumber.

Package Contents

Verify that all components are present before beginning installation:

  • 1 x Dual Flush Push Button Assembly (Silver plastic)
  • 2 x Flush Rods (one green, one black)
Disassembled components of the dual flush button, showing the main button, cap, and two flush rods.
Figure 1: Disassembled components of the flush button, including the main button assembly, the cap, and the two flush rods (green and black).

Specifications

FeatureDetail
Product TypeToilet Push Button
CompatibilityGeberit Impuls 250 Dual Flush Valve, Geberit Impuls 250 Twico 1
MaterialPlastic (Silver finish)
Screw Diameter38 mm
Flush Rod Length18 cm
ColorSilver button, Green and Black rods
OriginMainland China
Detailed view of the disassembled components with measurements: 38mm diameter for the screw part and 18cm length for the flush rods.
Figure 2: Dimensions of the flush button components, showing 38mm screw diameter and 18cm rod length.

Installation Instructions

This dual flush button is designed as a replacement part. Follow these general steps for installation:

  1. Turn off Water Supply: Locate the water shut-off valve for your toilet, usually on the wall behind or near the toilet, and turn it off. Flush the toilet to empty the tank.
  2. Remove Old Button: Carefully unscrew or unclip the existing flush button from the toilet cistern lid. Disconnect any rods or cables attached to the flush valve mechanism.
  3. Prepare New Button:
    • Insert the green and black flush rods into the designated holes on the underside of the new button assembly. Ensure they are securely seated.
    • The button assembly features a screw mechanism (38mm diameter) for securing it to the cistern lid.
  4. Install New Button:
    • Place the new dual flush button assembly through the hole in the toilet cistern lid.
    • From underneath the lid, secure the button assembly by tightening the screw mechanism. Do not overtighten.
  5. Connect Flush Rods:
    • Carefully lower the cistern lid back onto the toilet tank.
    • Adjust the length of the green and black flush rods as needed to properly engage with the dual flush valve mechanism inside the tank. The rods should be long enough to activate the valve without being too long and causing constant flushing.
    • Connect the ends of the flush rods to the corresponding levers on the Geberit Impuls 250 flush valve. Typically, one rod activates the full flush and the other activates the half flush.
  6. Test Functionality:
    • Turn the water supply back on.
    • Allow the toilet tank to refill.
    • Press each part of the dual flush button to ensure both the full and half flush mechanisms are working correctly and the water stops flowing after each flush.
Assembled Geberit Impuls 250 Dual Button Flush Valve, showing the silver button and the green and black rods ready for installation.
Figure 3: Assembled dual flush button with rods.

Operating Instructions

The dual flush button provides two options for flushing, allowing for water conservation:

  • Half Flush: Press the smaller button (or the smaller section of the button) for a reduced water flush, suitable for liquid waste.
  • Full Flush: Press the larger button (or the larger section of the button) for a full water flush, suitable for solid waste.

Ensure the button is pressed firmly and released to allow the flush valve to reset properly.

Close-up of the dual flush button, showing the two distinct push areas for half and full flush.
Figure 4: Close-up of the dual flush button design.

Maintenance

To ensure optimal performance and appearance of your dual flush button:

  • Cleaning: Clean the button regularly with a soft cloth and mild, non-abrasive cleaner. Avoid harsh chemicals or abrasive pads, as these can damage the silver finish.
  • Inspection: Periodically check the flush rods for any signs of wear or misalignment. Ensure they move freely and do not stick.

Troubleshooting

If you encounter issues with your dual flush button, consider the following:

  • Button Sticks or Doesn't Return:
    • Check if the button is properly aligned in the cistern lid.
    • Ensure the flush rods are not bent or obstructed.
    • Clean any debris around the button mechanism.
  • Toilet Doesn't Flush or Flushes Weakly:
    • Verify that the flush rods are correctly connected to the flush valve levers.
    • Adjust the length of the flush rods to ensure they adequately activate the valve.
    • Check the flush valve itself for any issues (e.g., blockages, worn seals).
  • Continuous Running Water:
    • The flush rods might be too long, preventing the flush valve from fully closing. Adjust their length.
    • Inspect the flush valve for debris or damage that prevents it from sealing.

User Tips

No specific user tips were available from reviews or Q&A for this product. General tips for toilet maintenance apply.

Warranty and Support

For any warranty claims or technical support, please contact the seller directly through your purchase platform. Keep your purchase receipt as proof of purchase.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.