Bosch GO 3

Contents

BOSCH GO 3 Cordless Screwdriver User Manual

Model: GO 3 | Brand: Bosch

Introduction

Thank you for choosing the BOSCH GO 3 Cordless Screwdriver. This manual provides essential information for the safe and efficient operation, maintenance, and care of your tool. Please read this manual thoroughly before first use and keep it for future reference.

BOSCH GO 3 Cordless Screwdriver with features: Torque Adjustment, Smart Lighting, Auto Clamping
The BOSCH GO 3 Cordless Screwdriver highlighting its key features: Torque Adjustment, Smart Lighting, and Auto Clamping.

For a visual overview of the product and its capabilities, please watch the official product demonstration video below:

Official product demonstration video showcasing the BOSCH GO 3's features and various applications.

Safety Warnings

General Pneumatic Tool Safety Warning

  1. All usage rules must be followed when using, inspecting, and protecting tools.
  2. Stay alert, pay attention to the operation being performed while operating pneumatic tools, and remain alert. Do not use pneumatic tools when you feel tired or have reactions to medication, alcohol, or treatment. Instant negligence when operating pneumatic tools can lead to serious personal injury.
  3. When adjusting tools, replacing accessories, or maintaining tools, it is necessary to close the main air supply valve and unplug the tool air supply connector before operation.
  4. Do not use dangerous, worn or poor quality compressed air pipes, connectors or joints.
  5. Ensure that all compressed air pipes, connector joints, etc. are of the correct size and tightly connected.
  6. Keep the compressed air in the air compression system dry and clean, regularly check the filter element of the filter, and remove any accumulated water in the pipeline.
  7. Before starting the pneumatic tool, remove all adjustment keys or wrenches. Wrenches or keys left on rotating parts of pneumatic tools can cause personal injury.
  8. Do not lubricate tools with flammable or volatile liquids, such as kerosene or diesel.
  9. Anticipate and be alert to sudden changes in operation during startup and use of tools.
  10. When operating, hold the tool tightly and do not straighten the trachea, allowing it to have a certain degree of expansion and contraction to prevent it from jumping and injuring people.

Supplementary Safety Rules for Chamfering Machines

  1. Maintain a firm grip on the tool. Especially when starting the machine, hold the body firmly so that it cannot vibrate back and forth. Keep your hands away from rotating parts.
  2. Fix the workpiece properly. Using a fixing device or vise to fix the workpiece will be more secure than holding the workpiece in hand. Do not clamp the chamfering machine onto a vise or fixture, and do not place your face or hands close to the rotating part during use.
  3. Do not allow the tool to run when unmanned, only operate while holding the tool in hand. Please do not place the rotating machine on the ground or workbench until the chamfering machine is completely stationary before lowering it.
  4. Do not place the chamfering machine on the workpiece fragments. Otherwise, it may cause tool damage or malfunction.
  5. Do not touch the blade immediately after the operation is completed. Because they may have extremely high temperatures, which can burn the skin.
  6. If the machine accidentally falls or collides. Please check if the blade and machine are damaged, cracked, or deformed.
  7. Do not stand where the pneumatic tool is about to move when a rebound occurs. The rebound will drive the tool against the cutting direction at the winding point.
  8. Keep cutting tools sharp and clean. Tools with sharp cutting edges that are well maintained are not easily stuck and easy to control.

Setup

Before using the machine, please read the manual carefully.

1. Connect the Aerodynamics

Use the air quick connector provided with the machine. Connect one side to the machine through an O-ring (a) and the other side to the air pipe (aerodynamic).

Diagram showing air quick connector (a) for connecting to the air pipe.
Figure B: Air quick connector (a) for connecting the tool to the air supply.

2. Start/Close and Adjust Intake Volume

To turn on the machine, push the B push plate forward and press it. Release to turn off the machine.

Rotate the regulating valve (c) for adjustment:

  • Rotate clockwise to increase the intake volume.
  • Rotate counter-clockwise to reduce intake.

Note: Except for some non-ferrous metals and soft materials, chamfering work usually involves higher rotational speeds for better chamfer quality.

Diagram showing the B push plate and regulating valve (c) for starting/closing and adjusting intake volume.
Figure C: Controls for starting/closing the tool and adjusting the air intake volume.

Operating Instructions

3. Chamfer Operation

Attention: To prevent machine overload, blade damage, and poor surface quality due to excessive milling, the milling depth of one stroke should not exceed C0.8mm. Larger milling purposes can be achieved through multiple strokes.

  1. Place the guide plate above the workpiece to be milled without any contact between the blade and it.
  2. Turn on the machine switch and wait until the machine reaches maximum speed.
  3. When chamfering curves and straight edges, slowly advance the guide wheel in the direction of feed against the surface of the workpiece (see Figure D). Keep the guide wheel and arc guide plate flush with the workpiece surface and move forward at a uniform speed until the final milling is completed.
  4. When chamfering inner and outer circular holes, the guide wheel should be pushed forward one circle around the inner or outer circle on the surface of the workpiece to achieve chamfering. If necessary, it can be rotated two or more circles to achieve the best chamfering effect. The cutting direction is shown in Figure E.
  5. The shape and size of chamfers can refer to the "Main Parameters of Chamfering Machine" section.
Diagram showing feed direction for chamfering (Figure D) and internal/external cutting directions (Figure E).
Figure D: Illustrates the feed direction for chamfering. Figure E: Shows internal and external cutting directions.

4. Resize Chamfer - AX311, AX307

Attention: Before adjusting or checking the tool, ensure the machine is turned off and the air connector is unplugged to prevent accidental start-up.

If the required chamfer size is C1 or above, complete it multiple times, increasing by 0.5mm each time. Otherwise, it may reduce surface quality, shorten machine service life, and increase blade wear. If chamfer requirements are high, conduct a trial chamfer until requirements are met.

  1. Loosen the machine screw on the arc guide plate (d).
  2. Rotate the arc guide plate (d).
  3. Counterclockwise rotation reduces the cutting amount, while clockwise rotation increases it.
  4. Adjust to the required size, then tighten the machine screw on the guide plate (d).

Scale Reset: If there is an error in the scale indication, adjust the arc guide plate (d) clockwise to its maximum value. Align the maximum value of the scale ring (e) with the arrow. Finally, tighten the fastening screw to complete the scale reset of the curve part.

Diagram showing scale ring (e) and arc guide plate (d) for chamfer adjustment on AX311, AX307 models.
Figure F: Scale ring (e) and Figure G (reused Figure E label): Arc guide plate (d) for chamfer adjustment on AX311, AX307 models.

5. Resize Chamfer - AX320

Attention: Before adjusting or checking the tool, ensure the machine is turned off and the air connector is unplugged to prevent accidental start-up.

If the required chamfer size is C1 or above, complete it multiple times, increasing by 0.5mm each time. Otherwise, it may reduce surface quality, shorten machine service life, and increase blade wear. If chamfer requirements are high, conduct a trial chamfer until requirements are met.

  1. Loosen the hexagonal fastening screw (f) and tighten it, then take out the right angle guide plate (k).
  2. Loosen the hexagonal fastening screw (h) and rotate the right angle adjusting ring (g).
  3. Counterclockwise rotation reduces the cutting amount, while clockwise rotation increases it.
  4. After adjusting to the required size, tighten the hexagonal fastening screws (h), then install the right angle guide plate (k) in sequence and tighten the hexagonal fastening screws (f).
Diagram showing chamfer adjustment components (f, h, g, k) for AX320 model.
Figure H: Chamfer adjustment for AX320. Figure I (reused Figure I label): Right angle adjusting ring (g) and related screws (f, h, k).

Maintenance

Attention: Before maintenance, ensure the machine is turned off and unplugged to prevent accidental start-up. Regular maintenance and inspection significantly impact the service life and performance of pneumatic tools.

6. Replace Accessories - AX311, AX307

Note: Always use original AOCKE blades for replacement.

Before replacing the blade, ensure the machine is turned off and the air connector is unplugged. Check the blade for wear; worn or dull blades affect chamfering and shorten machine life.

The cutter bar has two blades, each with four cutting edges. When an edge becomes blunt, rotate the blade 90° to use a new edge. Replace with new blades when all 8 cutting edges are blunt.

Replace the blade and guide wheel:

  1. Loosen the hexagonal fastening screw (l) and remove the arc guide plate (d).
  2. Replacing the blade: Use the included red flag wrench to remove the countersunk screw (m) that fastens the blade. Rotate or replace blade (n).
  3. Replacing the guide wheel: Use the included Allen wrench to remove the screw (o) that fastens the guide wheel. Replace with a new guide wheel (p).
Diagram showing blade replacement (J) and guide wheel replacement (K) for AX311, AX307 models.
Figure J: Blade replacement for AX311, AX307. Figure K: Guide wheel replacement for AX311, AX307.

7. Replace the Blade - AX320

Note: Always use original AOCKE blades for replacement.

Before replacing the blade, ensure the machine is turned off and the air connector is unplugged. Check the blade for wear; worn or dull blades affect chamfering and shorten machine life.

The cutter bar has two blades, each with four cutting edges. When an edge becomes blunt, rotate the blade 90° to use a new edge. Replace with new blades when all 8 cutting edges are blunt.

Follow these steps every time replacing the blade:

  1. Loosen the hexagonal fastening screw (f) and remove the right angle guide plate (k).
  2. Use the included red flag wrench to remove the countersunk screw (m) that fastens the blade. Rotate or replace blade (n).
  3. Finally, install the right angle guide plate (k) in sequence and tighten the screws.
Diagram showing blade replacement (I) and countersunk screw (L) for AX320 model.
Figure I (reused Figure I label): Blade replacement for AX320. Figure L: Countersunk screw (m) and blade (n) for AX320.

8. Maintenance and Upkeep

  1. Regarding the air compressor and its accessories: To achieve full performance, use clean and dry compressed air. Before use, filter and remove rust and moisture from the air compressor pipeline. Install a filter or a more efficient three-point combination.
  2. Regarding fuel supply: To maintain stable performance, regularly supply oil for pneumatic tools. Insufficient oil supply can cause overheating, wear, insufficient power, and reduced performance, greatly affecting the tool's lifespan.
  3. Cylinder section: Before daily operation, drop an appropriate amount of specialized oil for pneumatic tools from the air inlet and let it idle for about 3-5 seconds to lubricate.
Diagrams showing oil injection port for maintenance (Figure M and N).
Figure M and N: Illustrate the oil injection port for routine maintenance.

Troubleshooting

This manual does not contain a dedicated troubleshooting section. However, many issues can be prevented by following the safety warnings and maintenance guidelines provided.

  • If the tool is not operating as expected, first check the air supply for proper connection and quality (clean, dry air).
  • Ensure blades are sharp and correctly installed.
  • Verify that the intake volume is adjusted correctly for the task.
  • If the tool falls or collides, inspect for damage, cracks, or deformation before further use.

For persistent issues, please refer to the Warranty/Support section for contact information.

Specifications

General Product Properties

  • Brand Name: Bosch
  • Model: GO 3
  • Type: Multifunctional Screwdriver
  • Power Source: Battery (DC)
  • Battery Included: Yes
  • Rated Voltage: 3.6V
  • Motor: Brushed
  • Electrified: Yes
  • Movable: Yes
  • Handheld: Yes
  • Certification: CE
  • Origin: Mainland China

Main Parameters of Chamfering Machine (Models AX307, AX311, AX320, AX311S)

Parameter AX307 AX311 AX320 AX311S
No-load speed 30000rpm 30000rpm 30000rpm 30000rpm
Guide wheel 7mm 11mm - 11mm
Circular hole range >7mm >11mm - >11mm
Plate thickness 4mm 5mm 2.5mm 2.5mm
Depth of counter- 8mm 10mm - 10mm
Chamfer angle 45 degree angle 45 degree angle 45 degree angle 45 degree angle
Cutting size C0-1.5mm C0-1.8mm, R1, R1.5, R2mm C0-1.8mm, R1, R1.5, R2mm C0-1.8mm, R1, R1.5, R2mm
Blade model AGF-390A AGF-600A AGF-600A AGF-600A
Machine weight 340g 350g 360g 350g

Due to continuous improvement and upgrading of the product, if there is any inconsistency in appearance or parameters, the actual product or new model shall prevail.

Exploded View and Parts List

Exploded view diagram of the chamfering machine showing all components.
Exploded view diagram of the chamfering machine.
S/N Number Name S/N Number Name S/N Number Name
1865026Arc guide plate14865024rear axle housing25865010trigger
2865025Scale ring15856282bearing 69526865014Trigger pin
3865028bearing seat16865001Casing27865017o-ring 14x2
4856158Round head screw17865027headless screw28865018Air regulating pin
5856197Guide wheelΦ7802058AGF-390A29865015regulating valve
856201Guide wheelΦ11865210AGF-600A30865016o-ring 9x2
6856220Torx screw18865211AGR-610A31865019Valve Pin 5x23.3
7865034cutter bar Φ7865212AGR-615A32865006o-ring 16x2
865032cutter bar Φ11865213AGR-620A33865005Intake shaft
8856205bearing 62619856171Cup head screw34865052Soft pad
9865023Front axle sleeve20865029Adjusting ring35865007poppet valve
10865020rotor21865030Right angle guide plate36865008taper spring
11865021air blade22865012Torsion spring37865009Filter cotton
12865051dowel23865011Push plate38865004o-ring 25x1.5
13865022cylinder24865013Push plate pin39865003Exhaust cover

Warranty & Support

Warranty Policy

Thank you for purchasing the AOCKE professional chamfering machine. The following is the product warranty policy:

Part Name Warranty Period
Wind bladeLifetime warranty
Rotor, cylinder, trigger set, regulating valve spring12 months
Fixed parts such as cutter bar, guide plate adjusting ring, bearing seat, casing, etc.3 months
Vulnerable parts such as blades, bearings, screws, sealing rings, and other partsNo warranty

Attribution of Return Maintenance Costs

Belong to Labor cost Parts cost Two-way
Within the warranty scopefreefreeUser paid
Outside the scope of warrantyfreeUser paidUser paid

Warranty Service & Exclusions

To ensure you receive warranty service, please fill out the warranty card and send the receipt back to the AOCKE after-sales service center. We value your feedback.

For warranty matters, please contact the store where you purchased this chamfering machine directly.

The following situations are not covered by the warranty:

  1. The machine is misused, abused, or severely overloaded.
  2. Product damage caused by external objects, foreign objects (sand or iron filings), accidental accidents, or improper transportation or storage.
  3. Any product that has been opened, repaired, replaced or modified by oneself.
  4. Damage caused by failure to use AOCKE's original parts and accessories according to regulations.
  5. Replacement of vulnerable parts such as blades, bearings, screws.

A comprehensive user manual in PDF format is available for download: BOSCH GO 3 User Manual (PDF)

User Tips

  • Always ensure you have the correct bit for the task to prevent damage to the screw head or workpiece.
  • Regularly check the battery indicator and charge the screwdriver using the Type-C port to ensure it's ready for use.
  • For optimal performance and longevity, adhere to the recommended maintenance schedule, especially regarding air supply quality and lubrication.
  • When working in dimly lit areas, utilize the smart LED lighting feature for improved visibility.

Frequently Asked Questions (FAQ)

No specific FAQ content was provided. For common questions, please refer to the relevant sections of this manual or contact customer support.

© 2023 Bosch. All rights reserved.


Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.