LAUNCH X431 X-PROG 3

Contents

LAUNCH X431 X-PROG 3 Car Key Programmer User Manual

Advanced Immobilizer & Key Programming Tool

1. Introduction

This manual provides essential information and instructions for using the LAUNCH X-PROG 3. The X-PROG 3 is a powerful anti-theft solution designed for professional repair shops and vehicle maintenance businesses, offering comprehensive vehicle key, engine, and gearbox programming capabilities across a wide range of vehicle models.

This document is intended for vehicle owners and repair technicians with basic knowledge of vehicle systems.

Copyright © 2021 by LAUNCH TECH CO., LTD. All rights reserved. Launch is a registered trademark of LAUNCH TECH CO., LTD in China and other countries.

Disclaimer

The contents of this document are subject to changes without notice due to continued improvements in design, manufacture, and methodologies. Launch is not liable for any damage or losses due to the use of this document.

2. Safety Information

Important Safety Note

Please read this manual carefully and understand all safety precautions before performing any operation with this product.

Safety Grades

Safety grade definitions used in this manual are as follows:

  • ⚡ Danger: Indicates a hazardous situation which, if not avoided, will result in death or serious injury to the operator or bystanders.
  • ❗ Warning: Indicates a hazardous situation which, if not avoided, could result in possible injury to the operator or bystanders.
  • ⚠ Caution: Indicates a hazardous situation which, if not avoided, could result in serious equipment damage or property losses.

Safety Precautions

  • Never collide, throw, or puncture the test equipment; avoid falling, extruding, and bending it.
  • Do not insert foreign objects or place heavy objects on your device. Sensitive internal components may be damaged.
  • Do not use the test equipment in exceptionally cold, hot, dusty, damp, or dry environments.
  • In places where the test equipment may cause interference or generate a potential risk, turn it off.
  • The test equipment is a sealed unit with no end-user serviceable parts. All internal repairs must be performed by an authorized repair facility or qualified technician.
  • Never place the test equipment near apparatus with strong electromagnetic fields.
  • Do not attempt to replace the internal rechargeable lithium battery. Contact the dealer for factory replacement.
  • Use only the included battery and charger. Risk of explosion if the battery is replaced with an incorrect type.
  • Do not disconnect power abruptly during formatting or uploading/downloading processes, as this may cause program errors.
  • Do not disconnect the battery or any wiring cables in the vehicle when the ignition switch is on, to avoid damage to sensors or the ECU.
  • Do not place any magnetic objects near the ECU. Disconnect the power supply to the ECU before performing any welding operations on the vehicle.
  • Use extreme caution when performing operations near the ECU or sensors. Ground yourself when disassembling PROM to prevent static electricity damage to the ECU and sensors.
  • When reconnecting the ECU harness connector, ensure it is firmly attached to prevent damage to electronic elements (ICs) inside the ECU.

FCC Statement

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: a. This device may not cause harmful interference. b. This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device. It generates, uses, and can radiate radio frequency energy. If not installed and used according to instructions, it may cause harmful interference to radio communications. If interference occurs, try to correct it by: reorienting the receiving antenna, increasing separation between equipment and receiver, or connecting the equipment to an outlet on a different circuit.

3. Product Overview

The LAUNCH X-PROG 3 is an advanced immobilizer and key programming tool. Below is a detailed view of the device and its components.

LAUNCH X-PROG 3 Device Components

Figure 1: LAUNCH X-PROG 3 Device Components

Table 1: X-PROG 3 Component Descriptions
No.Part NameDescription
1DB26 diagnostic connectorTo connect with all anti-theft cables.
2Benz key slotTo place Benz car key.
3Key slotTo place car key for RF defection.
4Key chip slotTo place key chip.
5Power indicatorRed light indicates faults. Orange light indicates functions normally.
6ValveTo tighten loose EEPROM board.
7EEPROM slotTo insert EEPROM board.
8Power portFor power charging.
9DB15 diagnostic connectorTo connect with main diagnostic cable.
10DIY slotTo insert vehicle DIY board.

4. Package Contents

The X-PROG 3 package includes the following items. Please note that accessories may vary by destination. Refer to your local dealer or the packing list supplied with your tool for exact contents.

LAUNCH X-PROG 3 Full Kit Contents

Figure 2: LAUNCH X-PROG 3 Full Kit Contents

  • Main unit (X-PROG 3 device)
  • Power adaptor
  • Main diagnostic cable
  • Fourth-generation data acquisition cable
  • Fourth-generation EEPROM data acquisition cable (without dismantling dashboard)
  • BENCH mode cable
  • MCU converter V1
  • MCU converter V2
  • MCU cable with multiple leads
  • EEPROM chip adaptor
  • Benz infrared analog acquisition key
  • User Manual

5. Setup

5.1 Power Source

The X-PROG 3 does not have an independent power supply. It can be powered up via one of the following methods:

  • Using the included power adaptor.
  • Connecting the device through the vehicle's Data Link Connector (DLC).

5.2 Establish Hardware Connection

Before connecting, ensure the vehicle's ignition is turned off. Locate the vehicle's Data Link Connector (DLC) correctly.

Table 2: Hardware Connection Guide
User ScenarioCable TypeEnd A ConnectionEnd B ConnectionEnd C Connection
Key ProgrammingMain Diagnostic CableLaunch VCI connector (for data transmission)Vehicle's DLCX-PROG 3
Engine/Gearbox ProgrammingPower CablePower SupplyN/AMain Diagnostic Cable (End B)
Engine/Gearbox ProgrammingMCU Cable with Multiple LeadsEngine or Gearbox (to be repaired/replaced)X-PROG 3N/A

5.3 Establish Wireless Connection

Ensure your LAUNCH diagnostic tool is properly connected with the X-PROG 3. For effective data transmission, using a USB cable to connect the diagnostic tool with the VCI connector is strongly recommended.

To check wireless connection:

  1. Slide down the status bar from the top of your diagnostic tool.
  2. Touch the Settings icon (⚙️) and navigate to Wireless and network > Bluetooth.
  3. Select the X-PROG 3 from the list of available devices. Wait until the connection is successful.

6. Operating Instructions

The X-PROG 3 supports various diagnostic functions including key programming, engine, and gearbox replacement. You can retrieve ECU information, read, erase, and write data for a range of chips.

6.1 Common Operations

To begin using the programmer, you must first enter the function interface on your LAUNCH diagnostic tool:

  1. Turn on your LAUNCH diagnostic tool and open the diagnostic App from the home screen.
  2. On the main diagnostic screen, select Anti-theft system from either Local Diagnose or Reset, then touch OK.
  3. A connection diagram will be displayed. Touch OK to proceed.
  4. Depending on your requirement, select one of the following options: Gearbox Learning, Anti-Theft System, or Engine System.

6.2 Key Programming

The anti-theft system allows access to key chip programming functions, including reading, retrieving, writing key information, and other key-related operations.

Locksmith-Level Key Programming Functions

Figure 3: Locksmith-Level Key Programming Functions

Operating on Key Programming (Example for BMW):

This procedure covers backing up current key data and generating new keys.

1. Backup Current Key Data:

  1. Touch Intelligent Mode.
  2. Touch OK to confirm the IMMO Type.
  3. Touch Key Operation.
  4. Touch Key Learning.
  5. Read the onscreen instructions and touch OK.
  6. Follow prompts to remove the key from the ignition switch (if smart key, place outside vehicle) and touch OK.
  7. Touch OK to save the key data when prompted.
  8. Enter a file name for the key data and touch OK.
  9. Confirm key file saved by touching OK.

2. Generate a New Key:

  1. Touch the desired blank key position in the Key Learning table.
  2. Place the new key into the programmer's key slot and touch OK.
  3. Confirm the key type. If using a smart key, touch YES.
  4. Once key generation is complete, touch OK.

6.3 Gearbox Programming

Use gearbox programming to restore old gearbox data or write new data after a gearbox replacement.

Operating on Gearbox Programming (Example for BMW):

This procedure involves gearbox connection and erasure of gearbox data.

1. Connecting the Gearbox:

  1. On the programmer function interface, touch EGS System to enter gearbox programming.
  2. Touch the correct chassis type.
  3. A corresponding connection diagram will appear. Touch OK.

2. Erasing Gearbox Data:

  1. Touch EGS Erasure.
  2. Touch DOWNLOAD when prompted that the function needs to download files.
  3. Touch OK after download.
  4. Touch DOWNLOAD again.
  5. Touch OK after successful download.
  6. Touch YES to confirm upgrading the FLASH (ensure supply voltage is stable and above 13V).
  7. Touch YES to confirm erasing (if CAFD Code File is lost or current CAFS does not support backup).
  8. Touch OK after EGS Erasure is successful.

6.4 Engine Programming

Engine programming supports reading engine data and writing backup data after an engine replacement.

Operating on Engine Programming (Example for Volkswagen):

This procedure covers chip ID retrieval, engine connection, data backup, and data restoration.

1. Retrieve Chip ID:

  1. Touch Engine.
  2. Select the Engine Brand.
  3. Touch Search for ECU model.
  4. Check the ECU model (usually printed on the back of the engine), enter the engine type in the dialogue box (e.g., MED17.7.7), and touch OK.

2. Connect the Engine:

  1. Touch View Wiring Diagram.
  2. Read the connection diagram, perform the proper connection based on the engine type, and then touch OK.
  3. Touch Read chip ID.
  4. When the Chip ID dialogue box appears, touch OK.

3. Backup Data:

  1. Touch Backup EEPROM Data.
  2. Enter a file name for the EEPROM data.
  3. Confirm the storage path and touch OK.
  4. Touch OK after data backup succeeds.
  5. Follow onscreen instructions to backup flash data as well.

4. Restore EEPROM Data:

Note: EEPROM restoration should only be performed when irrevocable faults have been encountered.

  1. Touch Restore EEPROM Data.
  2. Touch the desired Backup EEPROM file name.
  3. Confirm the selected file and touch OK.
  4. Touch OK when data is successfully restored.

7. Maintenance

7.1 General Care

  • Keep the device clean and free from dust and moisture.
  • Store the device in its protective case when not in use.
  • Avoid dropping or subjecting the device to physical shock.
  • Do not use harsh chemicals or abrasive cleaners on the device.

7.2 Software Upgrade

Regularly update your diagnostic software and App to ensure optimal performance and access to the latest vehicle models and functions.

To update Diagnostic Software & App:

  1. On the main diagnostic screen of your LAUNCH tool, tap Software Update to enter the update center.
  2. Check the software you wish to upgrade and then tap Update.
  3. Once downloading is complete, the software packages will install automatically.
  4. A dialogue box will confirm installation completion.

Note: You can pause the update process by tapping Stop and resume by tapping Continue. In case of network connection failure, tap Retry.

8. Troubleshooting

If you encounter issues with your X-PROG 3, consider the following common troubleshooting steps:

  • Connection Issues: Ensure all cables are securely connected. Verify Bluetooth connection status. Try connecting via USB for more stable data transmission.
  • Power Issues: Confirm the device is receiving power from either the power adaptor or the vehicle's DLC. Check power indicator light status.
  • Software Errors: Ensure your software is up-to-date. If an error occurs during programming, do not disconnect power abruptly. Restart the diagnostic tool and X-PROG 3.
  • Compatibility: Verify that the vehicle make, model, and year are supported by the X-PROG 3 for the specific function you are trying to perform. Refer to the official LAUNCH compatibility list.
  • Key/Chip Not Detected: Ensure the key or chip is correctly placed in the designated slot. Check for any physical damage to the key or chip.
  • ECU/Module Communication Failure: Double-check wiring diagrams and connections to the ECU/module. Ensure the vehicle's ignition is in the correct position (off for initial connection, on for certain operations as instructed).

For complex issues not resolved by these steps, please contact customer support.

9. Specifications

Table 3: X-PROG 3 Technical Specifications
ParameterValue
Input Voltage12 V DC
Input CurrentMax 500 mA
Power Consumption5W
Working Temperature0 to 50 °C
Storage Temperature-20 to 70 °C
Dimension (L x W x H)39 x 107 x 298 mm
Item Weight5kg (approximate, including packaging)
Wireless SupportBluetooth
External Testing CertificationCE
CertificationRoHS, CE
MaterialPlastic

10. User Tips

  • Compatibility Check: Always verify the compatibility of the X-PROG 3 with your specific LAUNCH X431 diagnostic tool (e.g., X431 V, X431 PRO3S+, PAD V) before use.
  • Software Updates: Keep your X-PROG 3 software updated to the latest version to ensure support for new vehicle models and functions, including critical updates for VAG MQB NEC35XX and Siemens Engine ECUs.
  • Connection Stability: For critical operations like ECU cloning or key programming, prioritize a stable USB connection between your diagnostic tool and the VCI connector to prevent data corruption.
  • Package Contents: Confirm all necessary adapters and cables are present in your kit for the specific task you intend to perform, as accessories may vary.
  • Storage: Store the X-PROG 3 and its accessories in the provided carrying case to protect them from damage and keep them organized.

11. Warranty & Support

Warranty Information

LAUNCH warrants this product against defects in workmanship and material for 1 year from the date of delivery. Final judgment of defects will be made by LAUNCH. The exclusive remedy for defective products is repair or replacement. LAUNCH is not liable for consequential or incidental damages.

Cases Not Covered by Warranty:

  • Products with altered, removed, or defected mechanical serial numbers.
  • Products exposed to extreme conditions (excessive temperature, moisture).
  • Damage from external causes (fire, dirt, sand, battery leakage, blown fuse, theft, improper electrical source usage).
  • Products subject to accidents, mishandling, unauthorized alteration, abnormal usage, improper installation, repair, or storage.

Order Information for Parts

Replaceable and optional parts can be ordered directly from your LAUNCH authorized tool supplier. Please provide the following information:

  1. Quantity
  2. Part number
  3. Item description

Customer Service

For any questions regarding the operation of your X-PROG 3, please contact your local dealer or LAUNCH TECH CO., LTD:

  • Tel: +86-755-84557891
  • E-mail: overseas.service@cnlaunch.com
Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.