JIKONG JK-B2A24S

Contents

JIKONG Smart Active Balancer Instruction Manual

Model: JK-B2A24S (and variants)

Brand: JIKONG

1. Introduction

This manual provides detailed instructions for the safe and efficient operation of your JIKONG Smart Active Balancer. This device is designed for real-time, active, energy transfer type equilibrium for lithium battery packs, supporting 2-24 series configurations. Please read this manual thoroughly before use and keep it for future reference.

2. Package Contents

  • 1 x Active Balancer
  • 1 x Balance Wires (75cm)

The balancer is typically packaged in a box, sometimes with additional accessories like an adapter board (recommended for convenience, but not always included).

JIKONG Smart Active Balancer and balance wires in a box

Image: JIKONG Smart Active Balancer and balance wires as typically packaged.

3. Specifications

AttributeValue
Brand NameJIKONG
TypeLIFEPO4 Battery BMS (Active Balancer)
Balance FunctionActive Balanced BMS
Hardware or SmartSMART BMS
Battery Series Supported2S, 4S, 8S, 12S, 16S, 17S, 20S, 22S, 24S
Battery Type SupportedLi-ion, LiFePo4, LTO, Lead Acid, Ultra-capacitors
Single Voltage Acquisition Range1V-5V
Voltage Accuracy±3mV
Voltage Difference After Balancing≤3mV
Balance Current Range0.1A-10A (model dependent, e.g., 2A, 4A, 5A)
Charging Current200A
Supply Voltage Range20V-100V (also specified as 40V-100V for some models)
Charge and Discharge PortCommon Port BMS
Extra FunctionBT/APP (Built-in Bluetooth)
FunctionOvercharge Protection, Over Discharge Protection, Overcurrent Protection, Short Circuit Protection
Usage ScenarioPower BMS, Energy Storage BMS, 3C Digital BMS
High-concerned chemicalNone
CertificationCE, RoHS
OriginMainland China
Working Temperature-20°C to 70°C
Self-consumption (Balancing)55mA@20V, 10mA@100V
Self-consumption (NOT Balancing)40mA@20V, 6mA@100V
InterfaceRS485, CAN (model dependent)
Dimensions (MM)162 x 100 x 20
Weight (G)595

Note: Specifications may vary slightly between specific models (e.g., JK-B2A16S, JK-B4A24S, JK-B5A24S).

JIKONG Smart Active Balancer detailed specification table

Image: Detailed specification table for various JIKONG Smart Active Balancer models.

Dimensions of the JIKONG Smart Active Balancer

Image: Physical dimensions of the balancer unit (162mm x 100mm x 20mm).

4. Setup

4.1 Hardware Connection

  1. Connect the protection board and battery pack according to the provided wiring diagram.
  2. Ensure that the last positive cord (B+) is securely connected to the most positive pole of the battery pack.
  3. The total voltage of the battery pack must be greater than 20V before starting up the balancer.

Refer to the following diagrams for correct wiring methods:

Wiring diagram for JK-B1A16S and JK-B2A16S models, showing 13S and 16S wiring methods, and DC-DC Booster wiring.

Image: Wiring diagrams for JK-B1A16S / JK-B2A16S models, including 13S and 16S configurations and DC-DC Booster connection.

Wiring diagram for JK-B1A24S and JK-B2A24S models, showing 24S and 20S wiring methods, and DC-DC Booster wiring.

Image: Wiring diagrams for JK-B1A24S / JK-B2A24S models, including 24S and 20S configurations and DC-DC Booster connection.

Example connection modes for various battery series (24S, 20S, 17S, 16S, 14S, 13S, 8S, 7S) for JIKONG Smart BMS.

Image: Example connection modes for various battery series (24S, 20S, 17S, 16S, 14S, 13S, 8S, 7S) for JIKONG Smart BMS.

4.2 App Installation & Connection

  1. Download the specified Bluetooth application. You can find the QR code on the product packaging box or visit the website: JIKONG App Documentation.
  2. Ensure your mobile device's Bluetooth is turned on.
  3. Open the Bluetooth application.
  4. Click on the top left corner of the app to search for available devices.
  5. Select your balancer's serial number from the list to connect.
  6. The default connection password is 1234.
  7. Use the display activation button or an additional switch on the balancer to activate the BMS if it's not automatically detected.
Screenshot of JIKONG BMS mobile app showing cell voltage and connection instructions.

Image: Mobile app screenshot demonstrating cell voltage display and connection instructions.

Mobile app screenshots showing basic and advanced settings for the JIKONG BMS.

Image: Mobile app screenshots displaying basic and advanced settings for the JIKONG BMS.

Video: A short demonstration of the JIKONG Smart Active Balancer's physical appearance and connectors.

5. Operating Instructions

5.1 Smart Energy Working Modes

The JIKONG Smart Active Balancer features intelligent working modes to optimize battery management:

  • Storage Mode: In transportation, storage, offline, or wireless transmission off mode, the BMS does not consume battery pack current.
  • Normal Working Mode: When the charger is inserted in storage mode and off mode, the BMS will immediately return to the normal working mode, and all the protection functions, equalization functions, and communication functions will return to normal working.
  • Standby Mode: When the battery pack is in the static state (no charge and discharge current and no equilibrium current), the BMS will automatically enter the standby state after the set time (1-30 days can be set) is exceeded.
  • Shutdown: To prevent the BMS from wasting power for a long time and damaging the battery pack, the BMS has an automatic shutdown voltage. The BMS automatically shuts down when a cell falls below the shutdown voltage.
Diagram illustrating the Smart Energy Working Mode Switching for JIKONG BMS.

Image: Diagram showing the transitions between Storage, Normal, Standby, and Shutdown working modes.

5.2 App Usage

  1. After successful hardware connection and app pairing, parameters need to be set for the first start-up.
  2. Navigate to the settings section in the app. The default password for settings is 123456.
  3. Set the correct number of battery strings (units) and battery type (e.g., Li-ion, LiFePo4, LTO).
  4. Once the parameters are set, return to the real-time status page.
  5. Check the battery status. If no error message is prompted, and normal operation is indicated, the system is functioning correctly. Blue indicates the highest cell voltage, and red indicates the lowest cell voltage.
JIKONG BMS Use Manual section with app screenshots and troubleshooting steps.

Image: Excerpt from the JIKONG BMS Use Manual, detailing app operation and troubleshooting.

6. Maintenance

  • Keep the balancer clean and dry. Avoid exposure to moisture or extreme temperatures.
  • Regularly inspect all wiring connections to ensure they are secure and free from damage.
  • Do not attempt to open or repair the balancer yourself. Refer to qualified personnel for service.

7. Troubleshooting

This section provides solutions for common issues you might encounter:

7.1 Fault Analysis and Troubleshooting

  • Issue: Incorrect B+ connection.
    Solution: Ensure that the last 'B+' line of the cable has been correctly connected to the positive pole of the battery.
  • Issue: Balancer not starting up or charger voltage issue.
    Solution: Start up after charging and ensure that the charger voltage is greater than 4V of the battery pack voltage. Also, check whether the charger has voltage output.
  • Issue: Inaccurate voltage readings.
    Solution: Measure the actual total pressure of the battery pack with a multimeter and input this value into the 'voltage calibration' setting on the parameter page in the app.
  • Issue: Inaccurate current readings.
    Solution: The B- and P- terminals of the protection board use two 7AWG wires. Both wires must be connected in parallel; otherwise, it will lead to current measurement errors. Measure the actual current of the battery pack with a clamp meter and input this value into the 'current calibration' setting on the parameter page. Higher actual current leads to higher calibration accuracy.
  • Issue: Inaccurate capacity display.
    Solution: An initial capacity is estimated based on monomer voltage when the protection board is powered on for the first time, which can be inaccurate. After the protection board is discharged to the cut-off voltage and then fully charged, the capacity will be calibrated, and the charging process should not be interrupted.
  • Issue: Designed string number inconsistent with actual string number.
    Solution: Check whether the 'unit quantity' in the parameter setting is set correctly.
  • Issue: No wiring or missing strings in the middle.
    Solution: Check whether the acquisition cable has fallen off or is improperly connected.

8. User Tips

  • The default password for the app connection is 1234.
  • The default password for app settings is 123456.
  • It is recommended to purchase and use an adapter board for more convenient wiring and connection.
  • The balancer supports cascade connection, allowing it to be used with battery packs larger than 24 series. Theoretically, it can support infinite cascade connections with Bluetooth communication.

9. Warranty and Support

The JIKONG Smart Active Balancer is designed with robust protection features, including Overcharge Protection, Short Circuit Protection, Over Discharge Protection, Overcurrent Protection, All-in Protection (for cable drop or poor contact), and Over Temperature Protection.

Diagram illustrating the six security protection features of the JIKONG BMS.

Image: Six Security Protection features of the JIKONG BMS.

This product is certified with CE and RoHS standards, ensuring compliance with relevant safety and environmental regulations.

Various certification documents for JIKONG products, including CE and RoHS.

Image: Various certifications for JIKONG products.

For technical support, warranty claims, or further assistance, please contact your authorized retailer or the manufacturer directly. Keep your purchase receipt as proof of purchase.


Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.