1. Introduction
This manual provides detailed instructions for the installation, maintenance, and troubleshooting of your new thermal-isolating polarizer glass. This component is crucial for maintaining optimal image quality and protecting the internal components of your 4-inch LED projector by managing heat and light polarization. It is compatible with various 4-inch LED projectors, including models like UC40 and UC46.
2. Specifications
| Feature | Detail |
|---|---|
| Model Number | GF3C0567 |
| Brand Name | JETTING |
| Dimensions (Length x Width x Thickness) | 96mm x 60mm x 1.2mm |
| Compatibility | Suitable for 4-inch LCD screens in LED projectors (e.g., UC40, UC46) |
| Material | Thermal-isolating Polarizer Glass |
| Certification | None |
| High-concerned chemical | None |
Package Includes: 1x Polarizer Glass
3. Installation Guide
Replacing the polarizer glass requires careful disassembly of your projector. Please follow these steps precisely. It is recommended to watch the accompanying video for visual guidance before starting.
Video: Projector Disassembly and Polarizer Glass Replacement Guide
Required Tools:
- Small Phillips head screwdriver
- Prying tool (optional, for separating casing)
Step-by-Step Instructions:
- Prepare the Projector: Ensure the projector is powered off and unplugged from all power sources. Place it on a clean, flat, and stable surface.
- Remove the Top Cover:
- Locate and remove approximately 6 screws securing the top cover of the projector.
- Carefully lift the top cover. Be aware that there may be wires connecting the control buttons on the cover to the mainboard. Gently disconnect these wires.
- Access the Mainboard:
- Locate the LCD ribbon cable connected to the mainboard. Gently press the white clip and flip up the black clip to release the ribbon cable.
- Unscrew any screws holding the mainboard in place.
- Carefully remove the mainboard, noting any other connected wires. It is advisable to take photos before disconnecting wires to aid in reassembly.
- Locate and Remove Old Polarizer Glass:
- Once the mainboard is removed, you will have access to the internal optical components. Identify the thermal-isolating polarizer glass. It is typically located in the light path, often behind a reflector.
- Gently pull out the old polarizer glass.

Image: Old (browned) vs. New Polarizer Glass and improved projection.

Image: Diagram showing the location of the insulating glass (polarizer) inside a projector.
- Install New Polarizer Glass:
- Before installation, ensure you remove any protective films from both sides of the new polarizer glass.
- The polarizer glass has one side with a polarizing film. This side should face the LCD screen. If the screen appears yellow after installation, try flipping the glass to the other side.
- Carefully slide the new polarizer glass into its slot from top to bottom.
- Important: Avoid touching the surface of the glass with your bare hands to prevent fingerprints and smudges that can affect image quality. Handle by the edges.

Image: Dimensions of the polarizer glass (96mm x 60mm).

Image: Polarizer glass showing 4-inch diagonal measurement.
- Reassembly: Reverse the disassembly steps. Reinstall the mainboard, reconnect all wires (refer to your photos if needed), and secure the top cover with all screws.
4. Maintenance
To ensure the longevity and optimal performance of your polarizer glass:
- Cleaning: If cleaning is necessary, use a soft, lint-free microfiber cloth specifically designed for optics. Lightly dampen the cloth with a small amount of lens cleaning solution (do not spray directly onto the glass). Gently wipe the surface.
- Handling: Always handle the glass by its edges to avoid leaving fingerprints or smudges.
- Storage: If storing the glass separately, keep it in a protective, anti-static sleeve or container to prevent scratches and dust accumulation.
5. Troubleshooting
Common Issues:
- Screen appears yellow after installation: This indicates that the polarizer glass might be installed with the incorrect orientation. Carefully remove the glass and try installing it with the other side facing the LCD.
- Dust or smudges on the projected image: This is likely due to dust or fingerprints on the polarizer glass or other optical components. Refer to the maintenance section for proper cleaning procedures.
6. User Tips
- Verify Compatibility: Before purchasing, always double-check the exact dimensions (length, width, thickness) of your projector's existing polarizer glass to ensure a perfect fit. Projector models can vary, and a slight difference in size can prevent proper installation.
- Model Specifics: While this polarizer is suitable for 4-inch LCD screens, specific projector models (e.g., HASATEK K6, HY300) may have unique requirements. Confirm the exact specifications needed for your projector model.
- Document Disassembly: Take photos or videos during the disassembly process, especially when disconnecting wires or removing components. This will serve as a valuable reference during reassembly.
7. Warranty and Support
For information regarding product warranty, returns, or technical support, please refer to the seller's policies or contact their customer service directly. Keep your purchase receipt as proof of purchase.