HAKKO FX-888DX

Contents

HAKKO FX-888DX Digital Soldering Station Instruction Manual

Thank you for purchasing a HAKKO product. This manual provides essential information for the safe and effective use of your soldering station. Please read it thoroughly before operation and keep it for future reference.

1. Introduction

The HAKKO FX-888DX is a professional-grade digital soldering station designed for electronics soldering, including PCB and mobile phone repair. It features an intuitive interface for temperature adjustment, a parameter lock for settings security, and enhanced power for efficient operation.

2. Set Contents and Assembly

The following items are included in your HAKKO FX-888DX Soldering Station package:

  • Station FX-888DX (1 unit)
  • Handpiece FX-8801 (1 unit)
  • Iron holder FH-800 (1 unit)
  • Cleaning sponge (1 unit)
  • Cleaning wire (1 unit)
  • Instruction Manual (this document)
HAKKO FX-888DX Soldering Station with all components
Figure 2.1: HAKKO FX-888DX Soldering Station and its included components.
Labeled diagram of HAKKO FX-888DX components
Figure 2.2: Labeled diagram illustrating the main components of the soldering station.

3. Specifications

The HAKKO FX-888DX Soldering Station features the following technical specifications:

FeatureSpecification
Power Consumption100 W
Temperature Range50 to 480ºC (120 to 899ºF)
Temperature Stability±1ºC (1.8ºF) (At idle temperature, when set to 200 to 480ºC (400 to 899ºF))
Station OutputAC 26 V
Station Dimensions (W×H×D)100 × 120 × 125 mm (3.9 × 4.7 × 4.9 in)
Station Weight1.2 kg (2.6 lb)
Handpiece Power Consumption65 W (26 V)
Handpiece Cord Length1.2 m (3.9 ft)
Tip to Ground Resistance<2 Ω (with T18-B tip)
Tip to Ground Potential<2 mV
Heating ElementCeramic heater

Note: The total length and weight of the handpiece exclude the cord. This product is applied with electrostatic countermeasures (ESD Safe). Specifications and appearance are subject to change without notice for product improvement.

4. Safety Warnings and Cautions

Please observe the following precautions to ensure safety and prevent injury or damage to the product.

WARNING: Failure to comply with a WARNING may result in serious injury or death.

  • This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
  • Children shall not play with the appliance.
  • Cleaning and user maintenance shall not be made by children without supervision.
  • When this product is not used, place the handpiece on the iron holder.
  • If the power cord is damaged, it must be replaced by the manufacturer, service agent, or a qualified person to avoid danger.
  • The tip reaches high temperatures when the power source is turned on. You may risk getting burned or causing a fire if mishandled.
  • Do not touch the metal parts near the tip.
  • Do not place anything that easily burns or ignites near the product.
  • Make sure that people nearby are aware of the "high temperature danger."
  • When the product is not in use, being repaired, or being cleaned, turn the power switch off and disconnect the plug from the power outlet.

CAUTION: Failure to comply with a CAUTION may result in injury to the operator, or damage to the items involved.

  • Before using this product, fully read all descriptions in this document.
  • Only use the product for soldering.
  • Do not hit the handpiece against a workbench or subject it to strong shocks to remove solder residue.
  • Soldering produces smoke, so make sure to work in a well-ventilated area.
  • Do not connect a handpiece that is not compatible with this unit. It may cause failure.
  • Turn the station off before connecting or disconnecting the handpiece to prevent damage to the P.W.B.
  • Use genuine HAKKO parts for included parts/replacement parts/options.
  • Do not modify this product.
  • Do not use damaged cords or plugs. Doing so can result in malfunction or injury.
  • Do not use the product if it has been dropped or shows signs of damage.
  • When inserting and removing the cord, hold the plug body and do not pull the cord.
  • Do not allow this product to get wet. Also, do not handle it with wet hands.
  • Do not perform any other actions that may be considered to be dangerous.

NOTE: This indicates procedures or information that are important in a process described in this document.

Handling precautions for ESD Safe products:

  • Not all plastic parts are insulators; they may be conductive. Be careful not to expose live electrical parts or damage insulating materials when performing repairs or replacing parts.
  • Be sure the product is grounded before use.

5. Setup and Initial Preparations

5.1 Iron Holder Preparations

  1. Push the slide lock and remove the bottom plate from the iron holder.
  2. Place the cleaning wire onto the bottom plate.
  3. Attach the bottom plate back to the iron holder base.
  4. Add water as needed to the front part of the iron holder. The small sponges absorb water and keep them moist.
  5. Wet the large sponge and place it on the iron holder.
  6. Place the handpiece in the iron holder.

NOTE: Do not use the cleaning sponge when it is dry. This can damage the sponge and the soldering tip.

Soldering stand with cleaning sponge and copper wire
Figure 5.1: The soldering stand with its cleaning sponge and copper wire.
Thermal sponge and clean copper wire packaging
Figure 5.2: Packaging for the thermal sponge (A1559) and clean copper wire (A1561).

5.2 Tip Cleaning

  • Cleaning sponge: Wipe the tip with a moist sponge to remove oxide.
  • Cleaning wire: Insert and remove the tip into the wire to remove oxide.

6. Operation

CAUTION: Place the handpiece on the iron holder and plug it in before turning on the power.

6.1 Initial Power On and Heating

  1. Turn the power switch ON.
  2. The digital display will show the current tip sensor temperature, then the set temperature.
  3. The tip will begin to heat up. The LED heater lamp indicates heating activity.
  4. The iron will reach the set temperature (Factory default: 350ºC/750ºF).
Front view of HAKKO FX-888DX station with digital display
Figure 6.1: Front view of the station showing the digital display and control buttons.
Side view of HAKKO FX-888DX station with power switch
Figure 6.2: Side view of the station showing the power switch.

6.2 Changing the Set Temperature

The station supports two modes for temperature setting: Normal Mode and Preset Mode.

Normal Mode (Factory Default)

To change the set temperature, simply turn the knob. The display will show the new set temperature. (Factory default temperature settings: 350ºC/750ºF).

Preset Mode

To enable this mode, set "Parameter No. 04" to [PrE] (see Section 7). The station can store up to 5 frequently used temperatures. To change the set temperature, turn the knob to select one of the registered temperatures. (Factory default preset temperatures: P1 250ºC, P2 300ºC, P3 350ºC, P4 400ºC, P5 450ºC).

6.3 Confirming the Set Temperature

In Normal Mode, the set temperature is continuously displayed. In Preset Mode, pushing the knob will momentarily display the selected preset number and its registered temperature.

6.4 Tip Temperature Correction (Adjust Mode)

Tip degradation can cause a deviation between the set temperature and the actual measured tip temperature. This mode allows you to minimize this deviation by entering the measured tip temperature (a soldering tip thermometer is required separately).

  1. To enable [On] or disable [OFF] the Adjust mode, go to "Parameter No. 06" (see Section 7).
  2. Press and hold the knob to enter correction mode.
  3. Turn the knob to adjust the displayed temperature to match the measured tip temperature. (Correctable range: Set temperature ±150ºC/±270ºF).
  4. Push the knob to confirm the correction.

NOTE: Correct the tip temperature only after the tip temperature has stabilized. Replacing or changing the tip may cause a deviation; correct the tip temperature frequently to match the measured tip temperature.

Video 6.3: Demonstration of HAKKO FX-888DX assembly, temperature setting, and soldering.

7. Parameter Settings

To enter the parameter settings menu, press and hold the knob while turning the power on. Then, use the knob to navigate and change parameters.

Procedure to Change Parameters:

  1. Press and hold the knob while turning the power ON.
  2. Turn the knob to select the desired parameter number.
  3. Push the knob to enter the parameter setting for that number.
  4. Turn the knob to change the setting value.
  5. Push the knob to confirm the setting.
  6. Press and hold the knob to finalize the settings and exit, or push the knob to choose [no] to change the value again.

NOTE: Changes will be lost if the power is turned off in the middle of setting. If a password is set (Parameter No. 05), you will be prompted to enter it before accessing settings.

Parameter No.Parameter Name/SummarySetting ValueFactory Default
01Display temperature unitºC/ºFºC (USA: ºF)
02Low temp alarm (H-E)30 to 150ºC (54 to 270ºF)270 (ºF)
03Changing the set temperature modenor/PrE (2P, 3P, 4P, 5P)5P
04Preset temperature: Registered temperatures50 to 480ºC (120 to 899ºF)P1 250ºC, P2 300ºC, P3 350ºC, P4 400ºC, P5 450ºC
05Password lock0 (unlock all), 1 (partial lock), 2 (lock all)0
06Adjust mode: [On]/[OFF] settingOn/OFFOFF (USA: OFF)
07Initial resetYes/NoNo

8. Maintenance

CAUTION: Turn the power off and unplug the power cord before inspecting or replacing any internal components. Do not file the tip end to remove the oxide; it will shorten the tip life.

8.1 Inspection

Check the resistance of the heating element:

  1. Unplug the soldering iron from the station.
  2. Measure the resistance of the plug of the iron connection cord:
    • Between pins 4 - 5 (heating element): Normal resistance 2.5 to 3.5 Ω (at room temperature)
    • Between pins 1 - 2 (sensor): Normal resistance 41 to 58 Ω (at room temperature)
  3. If the results from step 2 are abnormal, measure the resistance of the heating element directly:
    • Heating element (red): Normal resistance 2.5 to 3.5 Ω
    • Sensor (blue): Normal resistance 41 to 58 Ω (at room temperature)
  4. If the results from step 3 are abnormal, replace the heating element. If normal, send the unit (including the handpiece) for service.

Check the tip to ground resistance:

Between pin 3 - tip: Normal resistance <2 Ω. If this resistance increases due to flux residue and oxide, sand the circled areas (inside of the pipe tip and surface) with sandpaper to remove oxide.

Close-up of soldering iron handle and tip
Figure 8.1: Soldering iron handle, tip, nut sleeve, and non-slip heat shield.
Diagram of soldering iron tip assembly
Figure 8.2: Diagram showing the assembly of the soldering iron tip.

8.2 Daily Maintenance

  • Setting temperature: Use the lowest temperature whenever possible to prevent accelerated tip deterioration.
  • During work: Perform a visual check of the tip. Replace it if it is deformed or worn out. Use the cleaning sponge to wipe off any oxide or old solder.
  • After finishing work: Thoroughly clean the tip with the cleaning sponge and then coat it with new solder to prevent oxidation.

8.3 Periodic Maintenance

  • Tip: Wear and tear on the tip varies. Maintenance should be performed based on usage.
  • Handpiece: Remove any flux residue, debris, and other particulates on the nut, enclosure pipe, and nipple with industrial alcohol. Note: The tip to ground resistance will increase if the nut is loose.
  • Iron holder: Push the slide lock and remove the bottom plate, then remove the solder waste collected in the plate. Rotate the cleaning wire as needed to a clean side where solder is not accumulated.

9. Troubleshooting

CAUTION: Turn the power off and unplug the power cord before inspecting or replacing any internal components.

ProblemPossible CauseSolution
No operation even if power switch is turned ON.Power cord not securely plugged in.Insert the plug into the outlet. If the problem persists, send the main unit for service.
[H - E] appears.Heat capacity of the tip is too small for the object. / Low temp alarm set value is too small.Use a tip with a larger heat capacity. / Increase the value of the low temp alarm setting (Parameter No. 02).
[S - E] appears.Heating element not working. / Handpiece plug loose/disconnected. / Sensor not working.Measure heating element resistance; replace if abnormal. Turn power off, reconnect handpiece, then power on. Measure sensor resistance; replace heating element if abnormal. If problem persists, send for service.
[---] appears.Main unit not working.Send the main unit (including handpiece) back for service.
Sometimes the tip is not heating up.Heating element not properly soldered.Solder heating element once again. If the problem persists, send for service.
The solder is not wetting on the tip.Tip temperature too high/low. / Oxide on the tip.Set appropriate temperature. / Remove oxide (see Section 8.2).
The tip temperature is too high/low.Tip temperature not corrected.Measure and correct the value using Adjust Mode (see Section 6.4).

If you cannot find a solution in this manual, or if another problem occurs, please contact the retailer where you purchased the product or HAKKO support.

10. User Tips

  • Always use the lowest effective temperature for your soldering task to prolong tip life and protect components.
  • Regularly clean your soldering tip with a moist sponge or cleaning wire to remove oxidation and ensure good solder wetting.
  • After each use, re-tin the tip with a fresh layer of solder to prevent oxidation during storage.
  • Take advantage of the preset temperature function for frequently used temperatures to quickly switch between settings.
  • Periodically check and correct the tip temperature using the Adjust Mode with a tip thermometer to maintain accuracy.
  • Ensure proper ventilation in your workspace to disperse soldering fumes.

11. Warranty and Support

For product support, service, or inquiries, please contact HAKKO Corporation or your local distributor.

HAKKO CORPORATION

HEAD OFFICE
4-5, Shiokusa 2-chome, Naniwa-ku, Osaka 556-0024 JAPAN
TEL: +81-6-6561-3225
FAX: +81-6-6561-8466
Website: https://www.hakko.com
E-mail: sales@hakko.com

OVERSEAS AFFILIATES

U.S.A.: AMERICAN HAKKO PRODUCTS, INC.
TEL: (661) 294-0090
FAX: (661) 294-0096
Toll Free: (800) 88-HAKKO
Website: https://www.HakkoUSA.com
E-mail: Support@HakkoUSA.com

HONG KONG: HAKKO DEVELOPMENT CO., LTD.
TEL: 2811-5588
FAX: 2590-0217
Website: https://www.hakko.com.cn
E-mail: info@hakko.com.hk

SINGAPORE: HAKKO PRODUCTS PTE., LTD.
TEL: 6748-2277
FAX: 6744-0033
Website: https://www.hakko.com.sg
E-mail: sales@hakko.com.sg

For other overseas distributors, please visit: https://www.hakko.com/doc_network

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.