1. Introduction
This manual provides essential information for the safe and efficient use of your Flipsky 65150 Waterproof BLDC Motor with integrated ESC. This 2-in-1 combo is designed for high-performance marine applications, offering a compact and reliable solution for electric surfing boards, hydrofoils, eFoils, and underwater thrusters. Its IP68 waterproof rating ensures durability in aquatic environments.

2. Specifications
| Feature | Specification |
|---|---|
| Size | ∅ 65*150mm |
| KV Rating | 160KV |
| Voltage Range | 4-13S |
| Rated Current | 30A |
| Maximum Current | 70A |
| Insulation Current | AC500v/1ma/3s |
| Rated Power | 1500W |
| Maximum Power | 3000W |
| Rated Torque | 2.3N.m |
| Maximum Torque | 4.5N.m |
| Internal Structure | 12N/10p |
| ESC Drive Mode | PPM |
| Communication Port | USB (Type C) |
| ESC Driver Firmware | 5.2 VESC Tool 3.00 |
| ESC Support Mode | BLDC/FOC |
| Shaft Specifications | ∅ 12-0.005/-0.01 |
| Power Cable | 2*12AWG (∅ 4.5mm*140) |
| Power Plug | XT90 male |
| Weight | 2.0kg |


3. Setup
3.1 Components Overview
The Flipsky 65150 motor comes as a 2-in-1 unit, integrating the ESC directly into the motor housing. This design saves space, simplifies installation, and eliminates concerns about ESC waterproofing. The unit includes:
- 65150 BLDC Motor with integrated ESC
- Power cables with XT90 male connector
- PPM signal cable
- Type C USB communication cable
- Propeller (if included in package)

3.2 Wiring and Connections
Refer to the detailed diagram below for proper wiring and dimensions. Ensure all connections are secure and correctly oriented before applying power.
- Battery Connection: Use the XT90 male connector for connecting to your battery pack. Ensure correct polarity (red for positive, black for negative).
- ESC Signal: The ESC operates in PPM signal mode. Connect the PPM signal cable to your receiver or control unit.
- Communication Port: A Type C USB port is provided for connecting to a computer for VESC tool configuration and firmware updates.

3.3 Propeller Installation
Attach the propeller securely to the motor shaft. Ensure it is properly aligned and tightened to prevent slippage during operation. Refer to the motor shaft specifications (∅ 12-0.005/-0.01) for compatibility.

4. Operating Instructions
4.1 VESC Tool Configuration
The integrated ESC uses VESC firmware 5.2 (VESC Tool 3.00). Connect the motor to your computer via the Type C USB port to access the VESC Tool. This software allows for:
- Motor detection and calibration.
- Configuration of BLDC/FOC control modes.
- Setting current limits, voltage cutoffs, and other parameters.
- Monitoring real-time data during operation.
Always ensure your VESC Tool and firmware are up-to-date for optimal performance and safety.
4.2 Initial Power-Up and Testing
After configuration, perform initial tests in a controlled environment. For marine applications, test the motor in water to observe its performance and ensure all seals are intact. Monitor parameters like power, current, and temperature using the VESC Tool.
4.3 Application Fields
This motor is suitable for a variety of water sports and marine propulsion systems, including:
- Electric Surfing Boards
- Hydrofoils (eFoils)
- Underwater Thrusters
- Electric Kayaks/Boats

5. Maintenance
Regular maintenance ensures the longevity and optimal performance of your motor.
- Cleaning: After each use, especially in saltwater, rinse the motor thoroughly with fresh water to remove salt, sand, and debris.
- Inspection: Periodically inspect the motor for any signs of wear, corrosion, or damage to the cables and connectors.
- Propeller Check: Ensure the propeller is free from damage and securely attached. Replace if bent or chipped.
- Storage: Store the motor in a dry, cool place away from direct sunlight and extreme temperatures.
6. Troubleshooting
If you encounter issues with your Flipsky 65150 motor, consider the following:
- No Power: Check battery connections, ensure the battery is charged, and verify the XT90 connector is fully engaged.
- Motor Not Spinning: Confirm PPM signal connection to your control unit. Use the VESC Tool to check motor detection and configuration.
- Unusual Noise/Vibration: Inspect the propeller for damage or imbalance. Check for any foreign objects obstructing the motor.
- Overheating: Ensure the motor is adequately submerged for cooling during operation. Review VESC settings for current limits.
- Communication Issues (USB): Try a different USB cable or port. Ensure VESC Tool is correctly installed and drivers are up-to-date.
For complex issues, consult the VESC documentation or contact Flipsky support.
7. User Tips
- VESC Configuration: Take time to properly configure your VESC settings using the VESC Tool. Incorrect settings can lead to poor performance or damage.
- Propeller Selection: Experiment with different propeller types and pitches to optimize thrust and efficiency for your specific application.
- Battery Management: Always use a battery management system (BMS) with your lithium battery pack to prevent over-discharge, over-charge, and cell imbalance.
8. Warranty and Support
For warranty information, technical support, or service inquiries, please contact the seller or manufacturer directly. Keep your purchase receipt as proof of purchase.