1. Introduction
This manual provides detailed instructions for the installation, operation, maintenance, and troubleshooting of your Shengmilo M5 LCD Display Panel Kit. This kit is designed to enhance your E-bike experience by providing essential ride data and control functions through a clear, intelligent display and integrated control buttons. The M5 display features a 4.5-inch large screen and a waterproof design, suitable for various riding conditions.
2. Setup
2.1 Package Contents
- M5 LCD Display Unit
- Control Button Unit
- Wiring Harness
- Mounting Accessories (e.g., transfer rings)
2.2 Physical Connection
Carefully connect the M5 LCD Display and control button unit to your E-bike's main controller using the provided wiring harness. Ensure all connectors are securely fastened to prevent accidental disconnections during operation. The display unit is labeled 'Model: LCD M5 S/N: 605440 20A0506' on its rear.

2.3 Mounting the Control Buttons
The control button unit is designed for handlebar mounting. Select the appropriate transfer ring to match your handlebar's diameter. Compatible handlebar diameters include 22.2mm, 25.4mm, 28.6mm, and 31.8mm. Secure the control unit firmly to ensure stable operation.

3. Operating Instructions
3.1 Display Overview
The M5 LCD display provides real-time information about your E-bike's status. The main screen clearly shows key metrics:
- Electricity (Energy Bar): Indicates the current battery charge level.
- Speed: Displays your current riding speed in km/h (or mph, depending on settings).
- Speed Gear (PAS): Shows the current Pedal Assist System (PAS) level.
- The Mileage (ODO/TRIP): Displays either the total odometer reading (ODO) or the current trip distance (TRIP).

3.2 Display Functions and Icons
The M5 display features various icons and segments to convey comprehensive information:

- Speed (MAX/AVG): Toggle between current, maximum, and average speed readings.
- Walk Mode: Activates a low-speed assist for walking the bike.
- Cruise Control: Maintains a set speed without continuous throttle input.
- Auto/Manual Mode: Switches between automatic and manual control settings.
- Headlight Icon: Indicates if the E-bike's headlights are on.
- PAS Levels: Adjust the level of pedal assistance.
- ODO/TRIP: Displays total odometer or current trip distance.
- VOL (Voltage): Shows the battery voltage.
- CUR (Current): Displays the motor's current draw.
- RMTM (Real-time): May indicate real-time power output or other dynamic data.
- Units (mph/kmh, mile/km): Allows switching between imperial and metric units.
- Error Codes (e.g., E 010): Displays specific error codes if a fault is detected. Refer to the troubleshooting section or your E-bike's main manual for code definitions.
3.3 Control Buttons
The control button unit typically includes buttons for power, mode selection, and adjusting settings (e.g., PAS levels, display parameters). Consult your E-bike's main manual for specific button functionalities and advanced settings, such as adjusting speed limiters or power codes.
4. Maintenance
- Cleaning: Use a soft, damp cloth to clean the display screen. Avoid abrasive cleaners or solvents that could damage the screen or casing.
- Waterproofing: The display is designed to be waterproof, but avoid submerging it in water or exposing it to high-pressure water jets.
- Connections: Periodically check all wiring connections to ensure they are secure and free from corrosion.
- Impact Protection: Protect the display from direct impacts or drops, which could cause internal damage or screen cracks.
5. Troubleshooting
If you encounter issues with your M5 LCD Display Panel Kit, refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Display does not turn on | Loose wiring connection, low battery, faulty display. | Check all wiring connections. Ensure E-bike battery is charged. If problem persists, contact support. |
| Incorrect speed/mileage readings | Incorrect wheel size setting, faulty speed sensor. | Check display settings for correct wheel size. Inspect speed sensor and magnet for proper alignment. |
| Display shows an error code (e.g., E 010) | Specific E-bike system fault. | Note the error code and consult your E-bike's main instruction manual or contact the E-bike manufacturer for specific definitions and troubleshooting steps. |
| Buttons unresponsive | Loose connection, internal fault. | Check the connection of the control button unit. Ensure no debris is obstructing buttons. |
6. Specifications
| Feature | Detail |
|---|---|
| Brand Name | VLFINA (associated with Shengmilo) |
| Type | Display |
| Screen Size | 4.5-inch |
| Voltage Compatibility | 48V (as indicated for MX-01 compatibility) |
| Design Features | Waterproof |
| Control Button Dimensions (Switching View) | Approx. 48.00mm (Length) x 18.15mm (Width) |
| Control Button Dimensions (Side View) | Approx. 43.85mm (Height) x 22.2mm (Width) |
| Handlebar Diameter Compatibility | 22.2mm, 25.4mm, 28.6mm, 31.8mm |
7. User Tips
- Advanced Settings: For advanced settings such as adjusting speed limiters or changing power assist codes, always refer to the specific instruction manual for your E-bike's main controller. The M5 display acts as an interface, but core system parameters are often managed by the bike's central unit.
- Unit Conversion: Familiarize yourself with how to switch between metric (km/h, km) and imperial (mph, miles) units on the display to match your preference.
8. Warranty and Support
For any technical assistance, warranty claims, or further inquiries regarding your Shengmilo M5 LCD Display Panel Kit, please contact the seller or manufacturer directly. Ensure you have your product model and any relevant serial numbers available when seeking support.