KKMOON ET605

Contents

KKMOON ET605 Cable Port Tester User Manual

Model: ET605

1. Introduction

The KKMOON ET605 Cable Port Tester is a versatile diagnostic tool designed for network, telephony, and shielded cable testing. It integrates multiple functions including cable pairing checks, registered jack crimp tests (for RJ45 and RJ11 interfaces), POE polarity detection, and can withstand voltages up to 60V. This ensures comprehensive compatibility and safety for various cable types, enabling quick, accurate, and efficient completion of cabling, maintenance, and troubleshooting tasks.

KKMOON ET605 Cable Port Tester and Receiver
The ET605 Cable Port Tester and its receiver, highlighting key features.

2. Product Components

The ET605 Cable Port Tester package includes the following items:

  • Main Body (Cable Port Tester)
  • Receiver (Wire Tracker Receiver)
  • User Manual
Product List: Main Tester, Receiver, and Instructions
Contents of the ET605 package.

2.1 Device Overview

Product Introduction with labeled parts
Labeled components of the ET605 Cable Port Tester.

Key components include:

  • RJ45 Port: For testing Ethernet cables.
  • RJ11 Port: For testing telephone cables.
  • QC (Quality Check) Indicator: For crystal head crimp test.
  • Wiremap Indicator: For cable pairing check.
  • Flash Indicator: For switch flash function.
  • POWER Indicator: Indicates power status.
  • MODE/POWER Button: To switch modes and power on/off.
  • LED Indicators (1-8, G): Display wire status and pairing results.
  • RJ11/RJ45 Cable Jacks: Durable metal materials for repeated plugging/unplugging.

3. Specifications

Specifications table for ET605
Detailed specifications of the ET605 Cable Port Tester.
ET605 Cable Port Tester Specifications
Feature Category Function/Detail
Basic Functions
  • Cable Pairing Check (Wiremap)
  • Crystal Head Crimp Test (QC)
  • Switch (Flash)
  • PoE Test
Power By (Main Body) 9V Battery (not included)
Power By (Receiver) -- (Powered by main unit or passive)
Other Functions
  • Low Battery Indicator
  • Energy Saving
  • Auto Power Off
Package Includes
  • Main Body
  • Receiver
  • Box
  • Manual
Withstand Voltage Up to 60V
Dimensions (Main Body) Approx. 106 x 121 x 30 mm (L x W x H)
Weight Approx. 180g (excluding battery)

4. Setup

4.1 Battery Installation

The main body of the ET605 Cable Port Tester requires one 9V battery (not included) for operation. Follow these steps to install the battery:

  1. Locate the battery compartment cover on the back of the main tester unit.
  2. Gently slide or unclip the cover to open the compartment.
  3. Insert a new 9V battery, ensuring the polarity (+/-) matches the indicators inside the compartment.
  4. Close the battery compartment cover securely.
Battery compartment of the ET605 tester
Battery compartment for 9V battery installation.

The device features a low battery indicator to alert you when the battery needs replacement, ensuring uninterrupted testing.

5. Operating Modes

The ET605 offers several testing modes accessible via the MODE/POWER button.

5.1 Cable Pairing Check (Wiremap)

This function tests the continuity and correct pairing of wires within network, telephone, and shielded cables. The LED indicators (1-8, G) on both the main unit and the receiver will flash sequentially to show the wire status.

  1. Connect one end of the cable to the RJ45 or RJ11 port on the main tester unit.
  2. Connect the other end of the cable to the corresponding RJ45 or RJ11 port on the receiver unit.
  3. Press the MODE/POWER button until the 'Wiremap' indicator is active.
  4. Observe the LED sequence on both units.
Cable pairing check examples: Normal, Cross, Short, Shielded
Examples of LED indications for different cable conditions (Normal, Cross, Short, Shielded).

Interpretation of LED Flashes:

  • Normal: LEDs 1-8 and G flash sequentially on both units.
  • Cross: LEDs flash out of sequence (e.g., 1 and 6 flash together if wires 1 and 6 are crossed).
  • Short: One or more LEDs do not light up, indicating a short circuit.
  • Open: One or more LEDs do not light up, indicating an open circuit.
  • Shielded Cables: The 'G' (Ground) LED will light up if the shield is properly connected.

5.2 Crystal Head Crimp Test (QC Cable Port)

This function verifies the quality of the crimping on RJ45/RJ11 crystal heads.

  1. Connect the crimped cable to the RJ45 or RJ11 port on the main tester unit.
  2. Press the MODE/POWER button until the 'QC' indicator is active.
  3. Observe the LED indicators. If an 8-core wire is not properly crimped, the corresponding LED (e.g., No. 8 light) will not light up.
QC Cable Port test showing an improperly crimped wire
Example of a QC test indicating an improperly crimped wire (No. 8 light not lit).

5.3 Switch Flash Function

This feature helps locate a target cable connected to a network switch by observing the flashing LED on the switch port. This function is only applicable for 10M/100M switches.

  1. Connect one end of the cable to be located to the RJ45 port on the main tester unit.
  2. Connect the other end of the cable to a port on the network switch.
  3. Press the MODE/POWER button until the 'Flash' indicator is active.
  4. Observe the network switch. The LED corresponding to the connected cable's port on the switch will flash, allowing you to identify the target cable.
Switch Flash function in use
Using the Switch Flash function to locate a cable by observing the flashing LED on a network switch.

5.4 POE Polarity Detection

The POE (Power over Ethernet) polarity detection function ensures that the power polarity is correct before connecting POE-enabled devices, preventing potential damage due to incorrect wiring.

  1. Connect the POE cable to the RJ45 port on the main tester unit.
  2. Press the MODE/POWER button until the 'POE' indicator is active.
  3. Observe the LED indicators (1-8). The lights will indicate the power supply configuration.
POE polarity detection with various power supply configurations
Illustrates POE polarity detection, showing LED patterns for 12/36 core, 45/78 core, 4578 lights up, and 1236 lights up 8-core power supply.

Interpretation of POE LED Indications:

  • 12 or 36 lights up: Indicates 12/36 core power supply.
  • 45 or 78 lights up: Indicates 45/78 core power supply.
  • 4578 lights up: Indicates 45/78 core power supply.
  • 1236 lights up: Indicates 12/36 core power supply.

The device is designed to withstand up to 60V, ensuring stable operation in high-voltage POE environments.

6. Troubleshooting

  • No Power: Ensure the 9V battery is correctly installed and has sufficient charge. Replace the battery if the low battery indicator is on or if the device does not power on.
  • Inaccurate Test Results: Check that cables are securely connected to both the main tester and receiver units. Ensure the correct testing mode is selected for the task. Inspect cables for visible damage.
  • LEDs Not Lighting Up: This could indicate an open circuit, a short circuit, or an improperly crimped connector. Refer to the 'Cable Pairing Check' and 'QC Cable Port' sections for interpretation.
  • Switch Flash Not Working: Verify that the connected switch is a 10M/100M model. Ensure the cable is properly connected and the 'Flash' mode is active.

7. User Tips

  • Always power off the device when not in use to conserve battery life. The ET605 features automatic power-off for energy saving.
  • Keep the RJ45 and RJ11 ports clean and free of debris to ensure reliable connections.
  • For best results, test cables in a well-lit environment to clearly see the LED indicators.
  • The device is designed with a durable, anti-slip, and anti-drop body for enhanced longevity.
Durable body, anti-slip, anti-drop feature of the ET605
The ET605 features a durable, anti-slip, and anti-drop design.

8. Maintenance

  • Cleaning: Use a soft, dry cloth to clean the exterior of the device. Do not use abrasive cleaners or solvents.
  • Storage: Store the tester in a cool, dry place away from direct sunlight and extreme temperatures. If storing for extended periods, remove the 9V battery to prevent leakage.
  • Avoid Moisture: Keep the device away from water and high humidity to prevent damage to internal components.

9. Warranty and Support

For warranty information, technical support, or service inquiries, please refer to the documentation provided at the time of purchase or contact your retailer. Keep your purchase receipt as proof of purchase.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.