EACHINE TX1200 VTX

Contents

Eachine TX1200 FPV Transmitter Instruction Manual

Model: TX1200 VTX | Brand: EACHINE

1. Introduction

The Eachine TX1200 is a versatile 5.8GHz FPV (First Person View) video transmitter designed for use with RC airplanes and other remote-controlled vehicles. It features 40 channels, 4-level switchable power output (25mW, 200mW, 600mW, 1000mW), and supports Smart Audio for OSD configuration. This manual provides essential information for the proper setup, operation, and maintenance of your TX1200 FPV Transmitter.

2. Package Contents

Please check the package contents upon receipt to ensure all items are present:

  • 1 x Eachine TX1200 25/200/600/1000mW 5.8GHz 40 Channel FPV Transmitter
  • 1 x MMCX Antenna
  • 1 x MMCX to SMA Female Pigtail cable
  • 1 x AV Cable (JST, 6Pin)
  • 1 x User Manual
Contents of the Eachine TX1200 package, including the VTX, cables, antenna, and user manual.
Figure 2.1: Eachine TX1200 Package Contents

3. Specifications

FeatureSpecification
Brand NameEachine
ModelTX1200 VTX
Frequency5.8GHz
Channels40CH (5 Bands x 8 Channels)
Power Switchable25mW / 200mW / 600mW / 1000mW
Power Input7V-26V
Power Output5V (for camera supply)
ConnectorMMCX
Cable ConnectorJST, 6Pin
Dimensions36mm x 36mm x 5mm (30.5mm stackable hole)
Net Weight9g
Smart AudioSupported (1W Smart Audio)
Current Consumption (5V Camera Supply)
  • 95mA (Typical) @ 25mW/12V
  • 180mA (Typical) @ 200mW/12V
  • 300mA (Typical) @ 600mW/12V
  • 480mA (Typical) @ 1000mW/12V
Eachine TX1200 FPV Transmitter with antenna, highlighting 4-level power switchable options and corresponding current consumption.
Figure 3.1: Power Levels and Current Consumption
Technical diagram of the Eachine TX1200 VTX showing dimensions, net weight, and a detailed 40-channel frequency table across 5 bands.
Figure 3.2: Dimensions and Frequency Table

4. Setup and Wiring

The Eachine TX1200 VTX requires careful wiring to your flight controller and camera. Refer to the diagram below for proper connections.

4.1 Wiring Diagram

Close-up view of the 6-pin JST connector on the Eachine TX1200 VTX board, showing wiring.
Figure 4.1: TX1200 VTX Connector Pinout

The 6-pin JST connector typically includes the following connections:

  • 7-26V Input: Connect to your main battery voltage (e.g., 2S-6S LiPo).
  • GND: Ground connection.
  • Video: Video signal input from your FPV camera.
  • GND: Ground connection for video.
  • 5V Output: Regulated 5V output for powering your FPV camera.
  • Smart Audio: Connect to a UART TX pad on your flight controller for OSD configuration.

Ensure all connections are secure and correctly polarized before applying power to avoid damage to the VTX or other components.

5. Operating Instructions

The Eachine TX1200 features a single button for controlling channel, band, and power settings. An LED display provides visual feedback on the current settings.

5.1 Button Control Modes

Diagram illustrating button control for Channel, Power, Band Selection, and Pit Mode on the Eachine TX1200 FPV Transmitter.
Figure 5.1: Button Control Interface
  • Channel Select:
    Short presses of the button will sequentially change through the 8 available channels within the current band. The Blue LED 1 will light up only for Channel 1.
  • Band Select:
    Press and hold the button for approximately 4 seconds. The Red LED 1 will flash, indicating you are in Band Select mode. Then, short press the button to cycle through the 5 available bands.
  • Power Select:
    Press and hold the button for approximately 8 seconds. The Green LED 1 will flash, indicating you are in Power Select mode. Short presses will then cycle through 200mW, 600mW, and 1000mW sequentially. The Green LED 1 lights up for 25mW. All three LEDs (Blue, Red, Green) will light up simultaneously to represent 1000mW.
  • Pit Mode:
    While in Pit Mode, you can change channels and power levels without transmitting a strong signal. The VTX has a memory function for settings. To exit Pit Mode, press and hold the button for 15 seconds until all 16 LEDs turn off and then light on again. This indicates you have exited Pit Mode and the VTX will transmit at the selected power level. By default, Pit Mode will send a very weak signal.

5.2 Smart Audio OSD Configuration

The TX1200 supports Smart Audio, allowing you to configure VTX settings directly from your flight controller's OSD (On-Screen Display). Ensure the Smart Audio pin is connected to a UART TX pad on your flight controller and configured correctly in your flight control software (e.g., Betaflight).

6. User Tips

No specific user tips from reviews or Q&A are available at this time. Always ensure proper cooling for the VTX, especially when operating at higher power levels (600mW or 1000mW), to prevent overheating and ensure longevity.

7. Maintenance

  • Keep the VTX clean and free from dust and debris.
  • Avoid exposing the VTX to excessive moisture or extreme temperatures.
  • Ensure proper airflow around the VTX, especially during operation, to prevent overheating.
  • Regularly check antenna connections for tightness to maintain optimal signal quality.

8. Troubleshooting

  • No Video Signal: Check all wiring connections, especially the video input from the camera and the VTX power supply. Ensure the VTX is powered on and transmitting on the correct channel/band.
  • Poor Video Quality/Static: Verify antenna connection and ensure it is not damaged. Check for interference from other electronic components. Try changing channels or bands. Ensure the VTX is not overheating.
  • VTX Not Responding to Button Presses: Ensure the VTX is powered correctly. If issues persist, disconnect and reconnect power.
  • Smart Audio Not Working: Verify the Smart Audio wire is correctly connected to a UART TX pad on your flight controller and that the UART is enabled and configured for VTX (Smart Audio) in your flight control software.

9. Warranty and Support

For warranty information or technical support, please refer to the official Eachine website or contact your retailer. Keep your proof of purchase for any warranty claims.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.