BEAR FORCE High Pressure Washer Water Cleaning Spray Gun

Contents

BEAR FORCE High Pressure Washer Water Cleaning Spray Gun

Model: High Pressure Washer Water Cleaning Spray Gun

Brand: BEAR FORCE

1. Introduction

Thank you for choosing the BEAR FORCE High Pressure Washer Water Cleaning Spray Gun. This manual provides essential information for the safe and efficient operation, maintenance, and troubleshooting of your new spray gun. Please read this manual thoroughly before use and keep it for future reference.

This high-quality water spray gun is designed for use with professional and commercial high-pressure washers, including Nilfisk-ALTO, WAP, KEW, and IPC PORTOTECNICA models.

2. Safety Information

  • Always wear appropriate personal protective equipment (PPE), including eye protection, when operating the pressure washer and spray gun.
  • Never point the spray gun at people, animals, or electrical equipment. High-pressure spray can cause serious injury.
  • Ensure all connections are secure before operating the pressure washer. Leaks can reduce pressure and cause hazards.
  • Do not operate the spray gun if any part is damaged or malfunctioning.
  • Keep children and pets away from the work area.
  • Always engage the trigger lock when the gun is not in use to prevent accidental discharge.

3. Package Contents

  • 1 x High Pressure Washer Water Cleaning Spray Gun with Quick Release Socket

4. Specifications

Specifications label on the spray gun

Figure 1: Specifications printed on the gun body

FeatureSpecification
Max Pressure280 bar / 4000 PSI
Max Temperature150°C / 300°F
Max Flow Rate40 L/min / 10.5 USGPM
Hose ConnectorM22x1.5 Male Thread, ID 14mm
Lance ConnectorKew Quick Release
Body MaterialEngineering Plastic
Handle TypeFinger Type
Interface MaterialCopper
Nozzle MaterialCopper
Water Spray TypeFan

5. Setup

Follow these steps to properly set up your high-pressure washer spray gun:

  1. Connect High-Pressure Hose: Locate the M22x1.5 Male Thread connector at the base of the spray gun handle. Securely screw the high-pressure hose from your pressure washer onto this connector. Ensure a tight, leak-free connection.
  2. Close-up of M22 male connector on the gun

    Figure 2: M22 Male Thread connector for hose

  3. Attach Spray Lance/Nozzle: The front of the spray gun features a Kew Quick Release socket. Insert your compatible spray lance or nozzle into this socket until it clicks securely into place.
  4. Close-up of Kew Quick Release nozzle connection

    Figure 3: Kew Quick Release socket for lance/nozzle

  5. Verify Connections: Double-check all connections to ensure they are firm and there are no visible gaps.

Video 1: Demonstration of hose and lance assembly

6. Operating Instructions

  1. Prepare Pressure Washer: Ensure your pressure washer is connected to a water supply and power source according to its own instruction manual.
  2. Unlock Trigger: Disengage the trigger safety lock (red lever) on the spray gun handle.
  3. Trigger lock mechanism on the spray gun

    Figure 4: Trigger lock in engaged position

  4. Start Pressure Washer: Turn on your pressure washer.
  5. Begin Spraying: Squeeze the trigger to start the high-pressure water flow. Release the trigger to stop.
  6. Adjust Spray (if applicable): If using an adjustable nozzle or different lances, adjust the spray pattern as needed for your cleaning task.
  7. Engage Trigger Lock: When finished or taking a break, always engage the trigger safety lock to prevent accidental spraying.

7. Maintenance

  • After Each Use: Disconnect the spray gun from the pressure washer and relieve any remaining pressure by squeezing the trigger.
  • Cleaning: Rinse the gun and connectors with clean water to remove any detergent residue or debris.
  • Inspection: Regularly inspect the gun for any signs of wear, cracks, or damage to the body, trigger, or connectors. Replace damaged parts immediately.
  • Storage: Store the spray gun in a clean, dry place, away from direct sunlight and extreme temperatures. Protect it from freezing temperatures, as residual water can expand and damage internal components.

8. Troubleshooting

  • No Water Flow: Ensure the pressure washer is turned on, connected to a water supply, and the trigger lock is disengaged. Check for kinks in the hose.
  • Low Pressure: Verify all connections are tight. Check for blockages in the nozzle or lance. Ensure your pressure washer is operating correctly.
  • Leaks from Connections: Tighten all threaded connections. Inspect O-rings and seals for wear or damage and replace if necessary.
  • Trigger Stuck/Hard to Squeeze: Ensure the trigger lock is fully disengaged. Check for any debris obstructing the trigger mechanism.

9. User Tips

  • For optimal performance, always use the spray gun with a pressure washer that matches its maximum pressure and flow rate specifications.
  • Consider using a quick-connect adapter for the hose connection if you frequently attach and detach the gun, to save time and reduce wear on threads.
  • When cleaning delicate surfaces, start with a wider spray pattern and lower pressure, gradually increasing as needed.

10. Warranty and Support

For warranty information, technical support, or to purchase replacement parts, please refer to the seller's contact information or the official BEAR FORCE website. Keep your purchase receipt as proof of purchase.


Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.