Smartgen BAC06A

Contents

Smartgen BAC06A Battery Charger Module Instruction Manual

For 12V/24V Lead-Acid Starting Batteries in Diesel Generator Sets

1. Product Overview

The Smartgen BAC06A is an intelligent floating charge battery charger specifically designed for 12V and 24V lead-acid starting batteries used in diesel generator sets. It incorporates advanced switch power supply components, ensuring efficient and reliable charging.

Key Features:

  • Switch Power Supply Structure: Offers a wide AC voltage input range, compact size, light weight, and high efficiency.
  • Two-Stage Charging Method: Utilizes a constant current followed by constant voltage charging profile, optimized for lead-acid batteries to prevent overcharging and extend battery life.
  • Protection Features: Includes built-in short-circuit and reverse connection protection for enhanced safety.
  • Adjustable Parameters: Charging voltage and current can be fine-tuned using on-site potentiometers.
  • LED Indicators: Features LED displays for power status and charging indication.
  • Easy Installation: Designed for convenient horizontal installation.
Front view of the Smartgen BAC06A battery charger
Figure 1: Front view of the Smartgen BAC06A Battery Charger.

2. Specifications

ParameterValue
Battery Voltage12V / 24V
Maximum Charging Current6A (for 12V) / 3A (for 24V)
Charging Voltage Range(13-14.5) V (for 12V) / (26-29) V (for 24V)
Charging Current Range(3-7) A (for 12V) / (1.5-3.5) A (for 24V)
AC Voltage Input(95-280) VAC
AC Frequency50 Hz / 60 Hz
Power Consumption120W (for 12V) / 115W (for 24V)
No Load Power ConsumptionLess than 3W
Efficiency80%
Working Temperature-40°C to 60°C
Storage Temperature-40°C to 85°C
Weight0.65 kg
Case Size (L x W x H)143 mm × 92 mm × 55 mm

3. Setup and Installation

The BAC06A charger is designed for convenient horizontal installation. Ensure the installation location provides adequate ventilation and is free from excessive moisture or extreme temperatures.

Wiring Connections:

Refer to the diagram below for proper wiring. All connections should be secure to prevent loose contacts and potential hazards.

Close-up of BAC06A charger wiring terminals and labels
Figure 2: Terminal block and connection points.
  1. AC Input (L, N): Connect the AC power supply (95-280 VAC, 50/60 Hz) to the 'L' (Live) and 'N' (Neutral) terminals.
  2. Battery Output (B-, B+): Connect the negative terminal of the battery to 'B-' and the positive terminal of the battery to 'B+'. Ensure correct polarity to avoid damage.
  3. Grounding: Although not explicitly shown in the provided image, it is always recommended to properly ground the charger's casing to a reliable earth ground for safety.
  4. Fuse: The charger includes a 10A fuse for protection. Ensure it is correctly installed.

Mounting:

Mount the charger horizontally using appropriate fasteners through the mounting holes on the casing. Ensure there is sufficient space around the unit for heat dissipation.

4. Operating Instructions

Once the charger is correctly installed and wired, follow these steps for operation:

  1. Power On: Apply AC power to the charger. The 'POWER' LED indicator should illuminate, indicating that the unit is receiving power.
  2. Charging Process: The charger will automatically begin the two-stage charging process (constant current followed by constant voltage) for the connected lead-acid battery. The 'CHARGING' LED indicator will illuminate during the charging phase.
  3. Adjusting Charging Parameters (Optional):
    • Voltage Adjustment (VOLT ADJ): Use a small screwdriver to carefully turn the 'VOLT ADJ' potentiometer to fine-tune the charging voltage within the specified range (13-14.5V for 12V batteries, 26-29V for 24V batteries).
    • Current Adjustment (AMP ADJ): Similarly, use the 'AMP ADJ' potentiometer to adjust the charging current within its specified range (3-7A for 12V, 1.5-3.5A for 24V).

    Caution: Adjusting these parameters incorrectly can damage the battery. Refer to your battery's specifications before making adjustments.

  4. Charging Completion: The 'CHARGING' LED will typically change state or turn off when the battery is fully charged and the charger switches to float mode, maintaining the battery's charge.

5. Maintenance

The Smartgen BAC06A battery charger is designed for reliable operation with minimal maintenance. However, regular checks can help ensure its longevity and optimal performance:

  • Keep Clean: Periodically clean the exterior of the charger to prevent dust and debris buildup, especially around ventilation openings. Use a dry, soft cloth.
  • Check Connections: Ensure all wiring connections (AC input and battery output) remain tight and free from corrosion.
  • Inspect for Damage: Visually inspect the casing and cables for any signs of physical damage.
  • Ventilation: Ensure the area around the charger remains well-ventilated to prevent overheating.

No specific internal maintenance is required or recommended for the user.

6. Troubleshooting

The BAC06A charger includes protection features to prevent common issues. If the charger is not functioning as expected, consider the following general troubleshooting steps:

  • No Power LED:
    • Check the AC power supply connection and ensure it is live.
    • Verify the input voltage is within the (95-280) VAC range.
    • Check the internal 10A fuse. If blown, replace it with a fuse of the same rating.
  • No Charging LED / Battery Not Charging:
    • Ensure the battery is correctly connected to the 'B-' and 'B+' terminals with correct polarity. The charger has reverse connection protection, but incorrect wiring will prevent charging.
    • Verify the battery voltage matches the charger's setting (12V or 24V model).
    • Check the battery's condition. A deeply discharged or faulty battery may not accept a charge.
    • Ensure the 'AMP ADJ' potentiometer is not set to minimum.
  • Overheating:
    • Ensure adequate ventilation around the charger.
    • Check for any obstructions blocking the ventilation holes.

The charger features short-circuit and reverse connection protection. If these conditions occur, the charger will typically cease operation or enter a protective mode. Correct the fault and restart the charger by cycling the AC power.

7. User Tips

No specific user tips were available from reviews or Q&A for this product. However, general best practices for battery chargers include:

  • Always connect the charger to the battery before connecting to AC power.
  • Disconnect AC power before disconnecting the battery.
  • Avoid operating the charger in extremely dusty or humid environments.
  • Ensure the battery being charged is compatible with the charger's voltage output (12V or 24V).

8. Warranty and Support

Specific warranty details are not provided in the product description. For warranty claims, technical support, or further assistance, please contact the seller or manufacturer directly.

Manufacturer/Brand: Smartgen (also associated with SAIWEI Electric)

Seller: SAI WEI Generator Parts Store

Please retain your purchase receipt for any warranty-related inquiries.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.