DykbRadio DP to EDP Cdriver board

Contents

DP+Type-C to EDP Driver Board User Manual

Model: DP to EDP Cdriver board | Brand: DykbRadio

1. Introduction

This manual provides detailed instructions for the DykbRadio DP+Type-C to EDP Driver Board, designed to convert DisplayPort (DP) and Type-C signals to EDP for various LCD screens, including those found in mobile phones, computers, and laptops. It supports resolutions up to 4K at 60Hz, 2.5K at 240Hz, and 2K at 165Hz.

DP+Type-c to EDP Driver Board

Figure 1: DP+Type-C to EDP Driver Board

2. Safety Warnings and Precautions

2.1 Safety Warning

  • WARNING: Keep away from children and avoid misoperation.
  • WARNING: Do not disassemble or modify this product yourself. Non-professional repairs may cause damage or safety accidents.

2.2 Precautions

  • Do not use the device in damp or dusty environments.
  • Avoid severe impact or vibration on the product.
  • Do not remove or insert the EDP cable while the device is powered on. Always power off the device, remove all other cables, and then unplug the EDP cable to prevent screen damage.

3. Product Overview and Components

The driver board features multiple input and output ports, as well as controls for volume and backlight. It is available in different versions depending on your screen's cable requirements.

Driver board with labeled ports and dimensions

Figure 2: Driver Board with Labeled Ports and Dimensions

3.1 Version Selection

  • Only Board: Includes the individual drive board only (does not include coaxial EDP cable).
  • Board W 40PIN CABLE: Includes the drive board + 0.5mm Spacing 40pin cable to 0.5mm Spacing 40pin cable for 40pin screens.
  • Board W 30PIN CABLE: Includes the drive board + 0.5mm Spacing 40pin cable to 0.5mm Spacing 30pin cable for 30pin screens.
Image showing only the driver board without cables

Figure 3: Only Driver Board (no cable)

3.2 Supported Computer Models and Pin Definitions

Diagram showing supported computer models and detailed EDP40 pin definitions and DP pin definitions

Figure 4: Supported Models and Pin Definitions

4. Setup and Installation

  1. Check Accessories: After unboxing, verify that all accessories are complete according to your selected version.
  2. Connect EDP Cable: Ensure the driver board is powered off. Carefully connect the appropriate EDP cable (30PIN or 40PIN) to your LCD screen and then to the EDP40 output on the driver board. The cable only supports coaxial cables of 0.5MM 40PIN in the same direction.
  3. Connect Signal Source: Connect your device (laptop, phone, etc.) to either the DP signal input or the Type-C signal input on the driver board. Note that DP and Type-C signals cannot be used simultaneously; switching between them while both are active will result in an error.
  4. Connect Power: Connect a 5V/QC15V power supply to the Type-C power input. For screens larger than 15W (e.g., 17 inches), use a 12V adapter for power. The board is compatible with USB Type-C PD3.0/3.1 and supports 100W QC protocol power chargers (2~5A current).
  5. Connect Audio (Optional): If desired, connect headphones to the 3.5mm audio output or speakers to the 2W speaker interface. If DP is used as the signal source, the audio line is a Thunderbolt 4 interface, so you must plug it into the computer to use the audio. A single line signal source can transmit both video and audio.
  6. Power On: Once all connections are secure, power on the driver board.

5. Operation

5.1 Signal Switching

In the initial state, the product defaults to Type-C 3.2 (Thunderbolt) signal. Press the designated button (refer to Figure 2 for location) again to switch back to the Thunderbolt 4 signal. The signal is one of two choices, allowing for a one-key switch.

5.2 Volume and Backlight Control

  • Volume and Mute: Use the key controls (SW1 dial switch) to adjust volume and mute the audio output.
  • Backlight Brightness: The default backlight brightness is 50% when the product starts. The dimming frequency is 2KHz, supporting non-polar dimming from 8% to 100% brightness. Adjust the minimum brightness to the maximum brightness over 5 seconds after downtuning.

5.3 Demonstration Video

Video 1: Demonstration of the driver board connected to a laptop, displaying a 240Hz refresh rate.

6. Specifications

FeatureSpecification
Working Voltage5V/QC15V protocol (compatible with USB Type-C PD3.0/3.1)
Power Charger Support100W QC protocol (Current 2~5A)
Power InputTYPE-C
Signal InputDP / Thunderbolt 4
Signal OutputEDP40
Backlight Voltage12V (default)
Drive Logic Voltage3.3V
Keystrokes Durability50,000 times
Operating Temperature-40°C to 85°C
Dimming Frequency2KHz (non-polar dimming 8%-100%)
Supported EDP30 Resolution (2LAN)1920x1080
Supported EDP40 Resolution (4LAN)1920x1080 300Hz, 2560x1440 240Hz, 3840x2160 120Hz, 5120x2880 60Hz (backward compatible)
Phone Reverse Power SupplySupports anti-adapter, reserves 15W for screen, QC15V fast charging
Audio Output3.5mm headphone interface, 2W speaker interface
Board DimensionsApproximately 39.98mm (width) x 92.57mm (length)
Product Weight0.027 kg
Package Dimensions18cm (length) x 14cm (width) x 3cm (height)

6.1 Supported Screens (Examples)

The board supports standard EDP screens up to 17.3 inches. Examples of tested compatible screens include:

  • NVIDIA Card Compatible: B156ZAN05.1 (4k 120Hz), 1080p 300Hz, 1080p 240Hz, Ne173qhm ny2, MNF601EA1-1, Ne156qhm_1y2, N156kme.
  • AMD Card Compatible: LP139UD1-SPC2 (3840 * 2160 60Hz), N156KME-GNA (2K165Hz), B133ZANxx.x, B156ZANxx.x, NE156QUMxxx, LQ156M1JWxx, B156HANxx.x, NV156QUM-N72, LTN156FLxx, MNG007DA1-1, B156HAN08.2/0, LQ156D1JW02, NV156FHM-N4N/K.
  • Desktop/Laptop Setups: Desktop T1000+nv140drm n61, Desktop 3080+b156zan05.1, Desktop Rx580+ne156qhm ny1, Desktop 3050ti+NE160QDM-NY2, Xbox (HDMI to DP)+NE160QDM-NY2 (native 2k only), Notebook 3070+n161hca ga1, Notebook 3070+Ne156qhm ny1, 5300g+N156KME-GNA, 5600g+N156KME-GNA, B156ZAN03.2, NV156FHM-NY0, N156hra ea1.

6.2 Unsupported Screens (Examples)

The board does NOT support industrial screens such as LVDS, MIPI, RGB, TL134GDXP01-00C, MNE208ZA1-3, TV160DKT-NH0, L134GDXP04-00C, TL142GDXP01-00C.

7. Maintenance

To ensure the longevity and optimal performance of your driver board, follow these maintenance guidelines:

  • Keep the device clean and free from dust. Use a soft, dry cloth for cleaning.
  • Store the board in a cool, dry environment when not in use.
  • Avoid exposing the board to extreme temperatures or humidity.
  • Handle the board carefully to prevent physical damage.

8. Troubleshooting

  • No Display / Signal Error: Ensure only one signal source (DP or Type-C) is active. Switching between them simultaneously will cause an error. Verify all cables are securely connected and the power supply meets the requirements.
  • Screen Damage after Connection: Always power off the device completely before connecting or disconnecting the EDP cable. Live insertion/removal can damage the screen.
  • Screen Incompatibility: The board supports standard EDP screens up to 17.3 inches. It does not support industrial screens (e.g., LVDS, MIPI, RGB, or specific models like LSN154YL01, b133xtn01.5, 5d11g02316). Please verify your screen's compatibility before purchase.
  • Audio Issues (Loud/Crackly): If audio is excessively loud or crackly, carefully adjust the volume using the SW1 dial switch. Check your computer's audio settings if using DP as the signal source, as it requires the computer to handle audio output.
  • Board Not Powering On: Ensure the power adapter provides 5V/QC15V and sufficient current (2-5A). For larger screens, confirm a 12V adapter is used.
  • General Malfunction: For persistent issues, refer to the comprehensive User Manual PDF for more detailed troubleshooting steps.

9. User Tips

  • Custom Casing: Consider building a custom 3D printed case for the driver board to protect it from physical damage and ensure stable connections, especially if using it in a portable setup.
  • Verify Screen Compatibility: Before purchasing or attempting to connect, double-check that your specific LCD screen model is compatible with this driver board. Refer to the 'Supported Screens' and 'Unsupported Screens' lists in the specifications.
  • Audio Adjustment: When using headphones, start with low volume settings and gradually increase to a comfortable level to avoid sudden loud audio.

10. Warranty and Support

For any issues or support inquiries, please contact our store support. For a comprehensive guide and additional information, please refer to the official User Manual PDF: User Manual (PDF).

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.