NISSEI RS-101

Contents

NISSEI RS-101 Shortwave SWR & Power Meter

Instruction Manual

1. Introduction

The NISSEI RS-101 is a high-quality Standing Wave Ratio (SWR) and Power Meter designed for shortwave radio communication. It provides accurate measurements of forward power, reverse power, and SWR across a frequency range of 1.8 to 60MHz. With adjustable power ranges up to 3KW, a clear pointer display, and LED backlight, it is an essential tool for amateur radio enthusiasts and professionals to ensure optimal antenna performance and transmitter efficiency.

Front view of the NISSEI RS-101 SWR & Power Meter
Figure 1: Front view of the NISSEI RS-101 SWR & Power Meter.

2. Product Overview

The RS-101 meter features a robust design suitable for desktop use. Key advantages include:

  • Wide Frequency Range: Operates from 1.8 to 60MHz, covering HF and 50MHz bands.
  • High Power Capability: Supports a maximum power of 3KW.
  • Clear Analog Display: Features a pointer reading for instantaneous and easy-to-interpret measurements.
  • LED Backlight: Ensures readability in various lighting conditions.
  • Peak Envelope Power (PEP) Mode: Supports measurement of peak envelope power during SSB mode transmission.
Diagram illustrating the four core advantages of the SWR & Power Meter
Figure 2: Core advantages of the RS-101 SWR & Power Meter.
Close-up of the meter showing PEP mode functionality
Figure 3: Detail of the meter highlighting Peak Envelope Power (PEP) Mode.
Close-up of the meter showing pointer reading and calibration note
Figure 4: Pointer reading display and note on calibration.

3. Specifications

FeatureSpecification
ModelRS-101
Frequency Range1.8 ~ 60MHz
Power Measuring Range0 - 3KW (Adjustable: 30W / 300W / 3KW)
Loss<= 0.1dB
Impedance50ohm
InterfaceSO-239 (M female)
Product Dimensions (L x W x H)190 x 80 x 105mm
Product Weight630g
Wireless FunctionNo
CertificationNone
OriginMainland China
Product dimensions of the NISSEI RS-101
Figure 5: Product dimensions (190mm x 80mm x 105mm).

4. Setup

Follow these steps to set up your NISSEI RS-101 SWR & Power Meter:

  1. Power Connection: Connect the provided power cable to the 12V DC input on the rear panel of the meter. Ensure correct polarity: the black wire is for negative, and the black and white wire is for positive.
  2. Transmitter Connection: Connect your radio transmitter's antenna output to the 'TX' (Transmitter) port on the rear of the RS-101 using a suitable coaxial cable.
  3. Antenna Connection: Connect your antenna to the 'ANT' (Antenna) port on the rear of the RS-101 using a suitable coaxial cable.
Rear view of the SWR & Power Meter showing TX, ANT, and 12V DC ports
Figure 6: Rear panel connections (TX, ANT, 12V DC).
Instruction image showing power cable connection and knob functions
Figure 7: Power connection details and overview of front panel controls.

5. Operating Instructions

To operate the NISSEI RS-101, familiarize yourself with the front panel controls:

  • FUNCTION Knob: Selects between FWD (Forward Power), REV (Reverse Power), and SWR measurement modes.
  • RANGE Knob: Sets the maximum power range for measurement (30W, 300W, or 3KW).
  • SWR SET Knob: Used for calibrating the SWR measurement.
  • PEP/AVG Button: Toggles between Peak Envelope Power (PEP) and Average power measurement modes.

5.1. Measuring Forward and Reverse Power

  1. Turn on the meter.
  2. Set the RANGE knob to an appropriate power range that is higher than your expected transmitting power.
  3. Set the FUNCTION knob to 'FWD' to measure forward power.
  4. Transmit a signal from your radio. The meter will display the forward power.
  5. Set the FUNCTION knob to 'REV' to measure reverse power. The meter will display the reflected power.

5.2. Measuring SWR (Standing Wave Ratio)

Calibration is required before measuring the standing wave ratio.

  1. Turn on the meter.
  2. Set the RANGE knob to an appropriate power range.
  3. Set the FUNCTION knob to 'FWD'.
  4. Transmit a continuous carrier signal (e.g., using FM or CW mode) from your radio at a low power setting.
  5. Adjust the SWR SET knob until the meter needle points to the 'CAL' mark on the SWR scale (usually full scale or a specific calibration point).
  6. While still transmitting, switch the FUNCTION knob to 'SWR'. The meter will now display the SWR.
  7. Once the SWR is read, stop transmitting.

Precaution: The maximum measured power of RS-101 is 3KW. When using a lower power range, it is important to ensure that the transmitting power of the radio station does not exceed the power of the corresponding range to prevent damage to the meter.

6. Maintenance

To ensure the longevity and accurate performance of your NISSEI RS-101 SWR & Power Meter, follow these maintenance guidelines:

  • Cleaning: Use a soft, dry cloth to clean the exterior of the meter. Do not use abrasive cleaners or solvents.
  • Storage: Store the meter in a cool, dry place away from direct sunlight, extreme temperatures, and high humidity.
  • Handling: Handle the meter with care to avoid physical shock or impact, which could affect its internal components and calibration.
  • Connections: Periodically check all cable connections for tightness and corrosion. Ensure connectors are clean and free from debris.
  • Power Supply: Always use a stable 12V DC power supply within the specified voltage range.

7. Troubleshooting

If you encounter issues with your NISSEI RS-101, consider the following common troubleshooting steps:

  • No Power: Check the 12V DC power connection and ensure the power supply is functioning correctly. Verify correct polarity.
  • No Meter Movement: Ensure all coaxial cables are securely connected to the 'TX' and 'ANT' ports. Confirm your radio is transmitting power.
  • Inaccurate SWR Readings:
    • Ensure the meter has been properly calibrated before taking SWR measurements (refer to Section 5.2).
    • Check the condition of your coaxial cables and connectors for any damage or shorts.
    • Verify that your antenna system is properly tuned for the operating frequency.
  • Meter Overload: If the needle pegs beyond the scale, immediately reduce your radio's transmitting power. Ensure the RANGE knob is set to a power range higher than your current transmitting power.

If problems persist after attempting these steps, contact customer support for further assistance.

8. User Tips

  • Start with Low Power: When first setting up or testing a new antenna, always start with the lowest possible transmit power and the highest power range setting on the meter to prevent accidental overload.
  • Regular Calibration: For the most accurate SWR readings, recalibrate the meter whenever you change frequency bands significantly or suspect a change in your antenna system.
  • Cable Quality: Use high-quality, low-loss coaxial cables for all connections to minimize measurement errors and power loss.
  • Environmental Factors: Be aware that environmental factors like nearby metal objects or changes in ground conditions can affect antenna performance and SWR.

9. Warranty & Support

For warranty information, technical support, or service inquiries, please refer to the contact information provided by your retailer or the manufacturer. Keep your purchase receipt as proof of purchase for warranty claims.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.