WINXU 260215P-01 Handlebar Twist Throttle

Contents

WINXU Handlebar Twist Throttle Speed Controller

Model: 260215P-01

Brand: WINXU

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your WINXU Handlebar Twist Throttle Speed Controller with LED Battery Capacity Display. This versatile throttle is designed for electric bicycles and scooters, supporting multiple voltage systems (24V, 36V, 48V, 60V).

2. Safety & Warnings

Read all instructions before use to ensure safety and prevent damage.

  • Warning: Keep the device and its cord out of reach of children under 3 years old.
  • Always disconnect the battery power supply before installing or performing any maintenance on the controller or throttle.
  • Do not work with the power on, as it may easily damage the equipment and pose a safety risk.

3. Specifications

AttributeValue
Product NameLED display throttle
TypeThrottle (Twist throttle)
Brand NameWINXU
OriginMainland China
Battery Voltage Compatibility24V / 36V / 48V / 60V
Working Voltage5V
Signal Output Voltage1.1V - 4.1V
Sensor TypeHall sensor
Wire Length1.5m (approximately 59 inches)
Handlebar Diameter22mm (approximately 0.87 inches)
Throttle Length113mm (approximately 4.45 inches)
Display Unit Dimensions49mm (width) x 36mm (height) (approximately 1.93 x 1.42 inches)
Dimensions of the WINXU Handlebar Twist Throttle
Figure 1: Dimensions of the Handlebar Twist Throttle. Overall length 162mm (6.38 inches), display unit 49mm x 36mm, grip length 113mm, handlebar diameter 22mm.

4. Setup & Installation

4.1 Pre-use Preparation

Before installing the throttle, ensure the battery power supply to your electric bicycle or scooter is completely disconnected. Working with power on can easily damage the equipment and is a safety hazard.

4.2 Wiring Diagram and Connections

Carefully read and understand the wiring diagram below before proceeding with the installation. Ensure all connectors are correctly identified and connected.

Wiring diagram for 2.8 Female+Bullet Connector and SM+Bullet Connector
Figure 2: Wiring diagram showing connections for 2.8 Female+Bullet Connector and SM+Bullet Connector types.

Wire Description:

  • Red Wire (5V+): Connects to the throttle +5V voltage on the controller.
  • Green Wire (Throttle Signal): Connects to the signal wire on the controller.
  • Black Wire (Negative Pole): Connects to the throttle negative on the controller.
  • White Wire (Electric Door Lock Input): Connects to the electric door lock wire on the controller.
  • Yellow Wire (Electric Door Lock Output): Connects to the electric door lock wire on the controller.
  • Bullet Connector: Used for the electric door lock (White wire: Input, Yellow wire: Output).

The throttle comes with a 1.5-meter wire for flexible installation.

Close-up of the throttle with key and wires
Figure 3: The throttle unit showing the key ignition and connected wires.
Throttle with key and display, showing wire length
Figure 4: The 24V LED Throttle with SM 3P+Bullet Connector, highlighting the 1.5m wire length.

5. Operating Instructions

5.1 Powering On/Off

Insert the key into the ignition slot on the throttle unit. Turn the key to the 'ON' position to power on the electric bicycle/scooter system and activate the throttle display. Turn the key to the 'OFF' position to power off.

Video 1: Demonstration of the throttle's functionality, including key ignition and LED display activation.

5.2 Using the Twist Throttle

Once the system is powered on, gently twist the throttle grip to accelerate. The Hall sensor provides a signal output voltage ranging from 1.1V to 4.1V, allowing for smooth and responsive speed control.

5.3 Interpreting the LED Battery Display

The integrated LED display shows the battery capacity. The display is designed to indicate the battery level across the supported voltage ranges (24V, 36V, 48V, 60V). Note that the display's sensitivity might show a full battery (e.g., 24V) with fewer than all LEDs lit if the battery voltage is at the lower end of the 'full' range for that system. For example, a 24V battery might show 2 out of 4 LEDs lit when fully charged, while 27-28V would show all 4 LEDs. The throttle sensor itself has a good sensitivity range of 0.8V to 4.1V.

6. Maintenance & Storage

6.1 Cleaning

Always turn off the device before cleaning. Use a soft, lint-free cloth to wipe the throttle and display. Do not use harsh chemicals or abrasive materials.

6.2 Storage

Store the throttle in a dry place at room temperature, ideally between 15°C and 35°C (59°F and 95°F).

6.3 Long-term Storage

If the device will not be used for an extended period, charge the battery to approximately 50% every 3 months to maintain battery health.

7. Troubleshooting

7.1 Wiring Issues

If the throttle is not functioning after installation, double-check all wiring connections against the provided diagram (Figure 2). Ensure that the correct wires are connected to their corresponding terminals on the controller. If the connectors do not match, professional assistance may be required to adapt the wiring, or ensure you have the correct throttle version for your controller.

7.2 Battery Display Inaccuracy

As noted in the operating instructions, the LED battery display may not always show all bars even with a fully charged battery, depending on the exact voltage of your battery system. This is a characteristic of the display's calibration across multiple voltage ranges. If the throttle itself is functioning correctly, this is likely normal behavior. If you suspect a fault, verify your battery voltage with a multimeter.

8. User Tips

  • Verify Connectors: Before purchasing or installing, carefully compare the connectors on your existing system with those on the new throttle. Some users have found it necessary to cut and splice wires due to incompatible connectors.
  • Professional Installation: If you are unsure about wiring or electrical connections, it is highly recommended to seek professional assistance to avoid damage to the product or your electric vehicle.
  • Battery Voltage Check: If the battery display seems off, use a multimeter to check your battery's actual voltage to understand its charge state relative to the throttle's display characteristics.

9. Disposal & Recycling

This symbol indicates that this product should not be treated as household waste. According to the WEEE Directive (2012/19/EU), it must be disposed of at an appropriate electronic waste collection point for recycling to prevent potential negative consequences for the environment and human health.

10. Manufacturer Information & Support

Manufacturer:

  • Name: ShenZhen Winxu Technology Co,.Ltd
  • Address: No.118, Building B, Yongxing Office Building, No. 68, Tianyun Road, Songgang Street, Baoan District, Shenzhen, China
  • E-mail: Winxutech@163.com
  • Tel: +86-15814065441

EU Authorized Representative:

  • Name: Vermilion Bird OU
  • Address: Tartu mnt 67/1-13b, Kesklinna linnaosa, 10115 Tallinn Harju maakond, Estonia
  • E-mail: vermilionbird.eu@outlook.com

For further assistance or inquiries, please contact the manufacturer or their authorized representative using the details provided above. You can also refer to the official user manual PDF for additional item guides and documents.

Official User Manual (PDF) reference: View User Manual PDF

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.