1. Introduction
The Tuya WiFi 3P4W Photovoltaic Smart Meter Circuit Breaker is an advanced home appliance protection device designed for monitoring and controlling electrical circuits. It features a digital LCD display for real-time data, smart app control via Tuya WiFi, and multiple protection functions including over-voltage, under-voltage, current limit, phase break, and more. Its automatic reclosing function enhances safety and convenience.
2. Safety Information
WARNING: Electrical shock hazard. Installation and servicing should only be performed by qualified personnel.
- This product does not have an isolation function. Always disconnect the main power supply at the front stage (e.g., main circuit breaker) before repairing or working on the circuit.
- The neutral line (N line) of this product is directly connected and does not have a disconnection function.
- Ensure the protector is wired strictly according to the markings on the device to prevent incorrect connections.
- While this product offers limited current protection, it is not a substitute for dedicated circuit breakers. Install appropriate circuit breakers (e.g., DZ47 and C65) at the front end of the line for comprehensive protection.
- Ensure all clamp screws are tightened securely before use to prevent poor contact and potential damage to the product or connected equipment.
- Do not operate the device if it appears damaged or malfunctioning.
3. Package Contents
Verify that all items are present and in good condition:
- Tuya WiFi 3P4W Photovoltaic Smart Meter Circuit Breaker x1
- User Manual (this document)
4. Product Overview
The device features a robust flame-retardant shell and a built-in smart chip for reliable performance. Its digital LCD display provides clear, real-time readings of electrical parameters.
Key Features:
- Digital LCD Display: Simultaneously displays 3 real-time data points (e.g., voltage for L1, L2, L3).
- Physical Button Design: Allows for manual control and threshold customization.
- Automatic Reclosing Protection: Automatically restores power after a fault is cleared.
- Multi-Protections: Includes over-voltage, under-voltage, current limit, phase break, zero drift, phase sequence, voltage imbalance, and current imbalance protections.
- Mobile APP Control: Remote monitoring and control via the Tuya Smart Life app.
- Easy Wiring: Large wiring ports facilitate quicker and more convenient installation.
- Installation: Guide rail type snap mounting for easy setup in distribution boxes.
5. Specifications
| Parameter | Value |
|---|---|
| Type | Conventional Circuit Breaker / Smart Meter |
| Is Smart Device | Yes |
| Rated Voltage | 80-380V |
| Rated Current | 100A |
| Rated Frequency | 50Hz |
| Connection | WiFi + Tuya APP |
| Operating Temperature | -20℃ to 60℃ |
| Operating Humidity | ≤85% |
| Altitude | Not exceeding 2000m |
| Pollution Level | Level 3 |
| Wiring Capacity | Insulated copper wire of 35 mm² and below |
| Dimensions (L x W x H) | 75mm x 89.5mm x 75.3mm (approx.) |
| Weight | 0.49 kg |
6. Installation
The device is designed for guide rail type snap mounting, making installation straightforward in standard distribution boxes. Ensure all safety precautions are followed before beginning installation.
- Mounting: Securely attach the circuit breaker to a standard DIN rail in your distribution box. No screws are required for mounting; simply snap it into place.
- Wiring: Connect the input and output wires to the designated terminals. The device features large wiring ports for ease of connection. Refer to the wiring diagram below and the markings on the device for correct phase (L1, L2, L3) and neutral (N) connections.
- Tighten Connections: After wiring, ensure all terminal screws are firmly tightened to prevent loose connections, which can lead to overheating or malfunction.
7. App and WiFi Setup
To utilize the smart features of your circuit breaker, connect it to the Tuya Smart Life app:
- Download App: Download and install the "Tuya Smart" or "Smart Life" app from your smartphone's app store (iOS or Android).
- Register/Login: Open the app and register for a new account or log in with an existing one.
- Enter Pairing Mode: Power on the circuit breaker. The WiFi indicator on the device will show its status:
- One flash: Waiting for WiFi signal to be detected (pairing mode).
- Two flashes: WiFi offline status.
- Three steady lights: WiFi is connected.
- Add Device: In the Tuya app, tap the "+" icon to add a new device. Follow the in-app instructions to discover and connect your circuit breaker to your home WiFi network. You may need to select the device type (e.g., "Circuit Breaker" or "Energy Meter").
- Configuration: Once connected, you can set thresholds, view real-time data, and remotely control the switch through the app.
8. Operating Instructions
The circuit breaker can be operated both manually via its physical buttons and remotely through the Tuya app.
8.1. Digital LCD Display
The LCD displays real-time electrical parameters. Use the physical buttons to navigate through different display modes.
8.2. Physical Buttons
The device features UP, DOWN, REV, SET, and OK buttons for navigation and configuration.
- UP/DOWN Buttons: Press to switch between displaying voltage, current, power, power factor, and frequency for the three phases.
- REV Button: Typically used for reviewing or cycling through display modes.
- SET Button: Used to enter the settings menu.
- OK Button: Used to confirm selections or exit menus.
8.3. Remote Control via App
Once connected to the Tuya app, you can:
- View real-time data (voltage, current, power, energy consumption).
- Remotely switch the circuit breaker ON/OFF.
- Set and adjust protection thresholds.
- Access fault records and historical data.
9. Function Settings
You can customize various protection parameters using the physical buttons on the device.
- Entering Settings: Long press the SET button to enter the setting status display page. A data bit will start flashing.
- Adjusting Values: Use the UP and DOWN buttons to change the value of the flashing bit.
- Switching Bits/Parameters: Short press the SET button to move to the next data bit or parameter.
- Confirming Settings: Short press the OK button to confirm the settings on the current page and proceed to the next settings page.
- Exiting and Saving: Long press the OK button to exit the setting state and save all changes.
Special Functions:
- WiFi Configuration / Factory Reset: From the "Voltage" interface, long press the SET button and hold to configure WiFi. This will switch the display to EPS. Long press again to clear power and display "Frequency Interface Restore factory configuration".
Configurable Parameters (Examples):
- Current Overload Lower Limit Delay: Range 0-9999 seconds (Default: 5s)
- Upper Limit of Current: Range 0.1-80A (Default: 80A)
- Upper Limit of Current Protection Delay: Range 0-9999 seconds (Default: 60s)
- Uneven Voltage Balance Protection: On/Off, 0-9999% (Default: On)
- Phase Sequence Protection: On/Off (Default: On)
- Power On Delay Protection: Range 0-9999 seconds (Default: 5s)
- Upper Voltage Limit: Range 60-300V (Default: 275V)
- Lower Voltage Limit: Range 60-300V (Default: 175V)
- Under/Over Voltage Protection Delay: Range 0-9999 seconds (Default: 20s)
- Lower Current Limit: Range 0.0-60A (Default: 0.0A)
10. Multi-Protections
The device offers comprehensive protection features to safeguard your electrical system and appliances:
- Over-voltage Protection: Disconnects power if voltage exceeds the set upper limit.
- Under-voltage Protection: Disconnects power if voltage drops below the set lower limit.
- Current Limit Protection: Prevents excessive current flow beyond the configured threshold.
- Phase Break Protection: Detects and acts upon loss of a phase.
- Zero Drift Protection: Monitors for neutral current imbalances.
- Phase Sequence Protection: Ensures correct phase rotation.
- Voltage Imbalance Protection: Detects significant voltage differences between phases.
- Current Imbalance Protection: Detects significant current differences between phases.
- Automatic Reclosing: If a fault is temporary and clears, the device will automatically reclose and restore power after a set delay.
Fault Record: The device maintains a record of faults such as overvoltage, undervoltage, overload, low current protection, voltage imbalance, current imbalance, and phase sequence protection. This record can be accessed via the Graffiti App (Tuya App).
11. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Device not powering on | No power supply; incorrect wiring; main circuit breaker tripped. | Check main power supply. Verify wiring connections. Reset upstream circuit breaker. |
| WiFi indicator flashing twice (offline) | No WiFi connection; incorrect WiFi password; device too far from router. | Ensure WiFi is active. Reconfigure WiFi via app or device settings. Move device closer to router. |
| Protections tripping unexpectedly | Actual electrical fault; incorrect protection threshold settings. | Check connected load for faults. Review and adjust protection thresholds in settings or via app. |
| Device not responding to app commands | No internet connection on phone; device offline; app malfunction. | Check phone's internet connection. Verify device WiFi status. Restart app. |
12. Maintenance
- Keep the device clean and free from dust and debris. Use a dry, soft cloth for cleaning.
- Avoid exposing the device to excessive moisture or extreme temperatures outside its operating range.
- Periodically check all wiring connections to ensure they remain tight and secure.
- Do not attempt to disassemble or repair the device yourself. Refer to qualified service personnel.
13. Warranty and Support
13.1. Guarantee Period
- Within 12 months from the date of production: If any product quality issues arise and the product's integrity (e.g., seals) is intact, our factory will provide a free replacement.
- Within 36 months from the date of production: If a quality issue occurs and the product's integrity (e.g., seals) is intact, our factory will provide free repair services.
Please retain your proof of purchase for warranty claims.
13.2. Technical Support
For technical assistance, troubleshooting, or warranty inquiries, please contact your retailer or the manufacturer's customer support. Refer to the product packaging or seller's website for contact details.