KKMOON DY4100

Contents

DY4100 Digital Earth Ground Resistance Meter Instruction Manual

Model: DY4100

1. Introduction and Overview

The DY4100 Digital Earth Ground Resistance Tester is a practical and precise instrument designed for measuring earth resistance in various electrical systems. It offers comprehensive functions, high accuracy, and user-friendly operation, making it suitable for both indoor and outdoor applications due to its dust and wet-proof structure.

This device can test the earth resistance of power systems, electrical equipment, and conductors, as well as measure AC voltage. Its digital display ensures clear readings and low energy consumption.

Key Features:

  • Large, clear digital display for easy reading.
  • Low energy consumption.
  • High accuracy and quick detection.
  • Three-gear measurement positions (20Ω, 200Ω, 2000Ω) for diverse applications.
  • Overload protection for enhanced safety.
  • Fast response time: approximately 5 seconds for ground resistance, 2 seconds for grounding voltage.
  • Durable protective cover design, resistant to falling, dust, and moisture.
  • Easy-to-use interface.
  • Detachable battery compartment for convenient battery replacement.

Video: DY4100 Digital Earth Ground Resistance Tester demonstration, showing the unit, accessories, and basic operation.

2. Package Contents

Please check the package carefully to ensure all items are present and undamaged. The standard package for the DY4100 model includes:

  • 1 x DY4100 Main Unit (Digital Earth Ground Resistance Tester)
  • 1 x Instruction Manual
  • 1 x 15-meter Red Test Wire
  • 1 x 10-meter Yellow Test Wire
  • 1 x 5-meter Green Test Wire
  • 1 x Set of Simple Test Wires (Red/Green)
  • 2 x Auxiliary Earth Bars (Ground Stakes)
  • 1 x Tool Bag

Note: Batteries are not included in the shipment. The device requires 6 x 1.5V (AA/R6AA) batteries and 1 x 12V (23A) battery.

DY4100 Package Contents

Image: Detailed view of the DY4100 package contents, including the main unit, various test leads, auxiliary earth bars, instruction manual, and carrying bag.

DY4100 Tester and Accessories

Image: The DY4100 Digital Earth Ground Resistance Tester shown with all its included accessories.

3. Specifications

ParameterValue
Model NumberDOUYI DY4100
Brand NameKKMOON
DIY SuppliesElectrical
CertificationCE
MaterialPlastics
Earth Ground Resistance Range0/20/200/2000Ω ± (2%+3)
Earth Voltage Range0~30V ± (3%+5)
Resolution0.01Ω
Required Batteries6 x 1.5V (R6AA), 1 x 12V (23A)
Item Size200 x 200 x 270mm (7.9 x 7.9 x 10.6in)
Item Weight1500g (3.3lb)
Package Size300 x 220 x 220mm (11.8 x 8.7 x 8.7in)
Package Weight1780g (3.9lb)

4. Setup

4.1 Battery Installation

  1. Open the battery compartment cover located on the back of the unit.
  2. Insert 6 x 1.5V AA batteries and 1 x 12V 23A battery, ensuring correct polarity (+/-).
  3. Close the battery compartment cover securely.
Battery Compartment

Image: View of the battery compartment for installing required batteries.

4.2 Connecting Test Leads and Auxiliary Earth Bars

The DY4100 supports both 2-pole and 3-pole measurement methods. Refer to the diagrams below for proper connection.

Wiring Diagrams for Earth Resistance Measurement

Image: Wiring diagrams illustrating 2-pole (left) and 3-pole (right) measurement methods for earth resistance. The image also lists earth resistance requirements for various applications.

4.2.1 2-Pole Measurement (Simplified)

This method is typically used for quick checks or when auxiliary earth bars cannot be deployed.

  1. Connect the green test lead to the 'E' terminal on the tester.
  2. Connect the red test lead to the 'C' terminal on the tester.
  3. Connect the other end of the green lead to the earth electrode under test.
  4. Connect the other end of the red lead to a known good earth point (e.g., water pipe, building ground).

4.2.2 3-Pole Measurement (Standard)

This method provides more accurate results by using two auxiliary earth bars.

  1. Connect the green test lead to the 'E' terminal on the tester.
  2. Connect the yellow test lead to the 'P' terminal on the tester.
  3. Connect the red test lead to the 'C' terminal on the tester.
  4. Drive the earth electrode under test into the ground.
  5. Drive the first auxiliary earth bar (P) into the ground at a distance of 5-10 meters from the test electrode.
  6. Drive the second auxiliary earth bar (C) into the ground at a distance of 5-10 meters from the first auxiliary earth bar (P), ensuring all three are in a straight line.
  7. Connect the other end of the green lead to the earth electrode under test.
  8. Connect the other end of the yellow lead to the 'P' auxiliary earth bar.
  9. Connect the other end of the red lead to the 'C' auxiliary earth bar.
Test Lead Connections

Image: Close-up of the E, P, C, and V terminals on the DY4100 for connecting test leads.

Auxiliary Earth Bars

Image: The two auxiliary earth bars (stakes) used for 3-pole measurements.

5. Operating Instructions

5.1 Power On/Off

Press the POWER button to turn the device on or off. The 'OK' indicator light will illuminate when the device is powered on and ready.

DY4100 Front Panel

Image: Front panel of the DY4100 showing the display, rotary switch, and control buttons.

5.2 Earth Voltage Measurement

  1. Rotate the function dial to the 'EARTH VOLTAGE' position.
  2. Connect the test leads to the 'E' and 'V' terminals.
  3. The display will show the measured AC earth voltage.

5.3 Earth Ground Resistance Measurement

  1. Ensure test leads and auxiliary earth bars are connected correctly for either 2-pole or 3-pole measurement (refer to Section 4.2).
  2. Rotate the function dial to the desired resistance range: '20Ω', '200Ω', or '2000Ω'. Start with the highest range if the resistance is unknown.
  3. Press the red TEST button. The 'OK' indicator will flash during measurement.
  4. The measured earth resistance value will be displayed on the screen.
  5. If the reading is '1' or 'OL', it indicates an over-range condition. Switch to a higher resistance range.
  6. If the reading is unstable, check the connections or the condition of the auxiliary earth bars.

5.4 Data Hold Function

During or after a measurement, press the yellow HOLD button to freeze the current reading on the display. Press it again to release the hold function.

5.5 Earth Resistance Requirements (General Guidelines)

  • AC working ground: Ground resistance should not be greater than 4Ω.
  • Safety working ground: Ground resistance should not be greater than 4Ω.
  • DC working ground: Ground resistance should be determined according to the specific requirements of the computer system.
  • Lightning protection ground: Ground resistance should not be greater than 10Ω.
  • Shielded systems (combined grounding): Ground resistance should not be greater than 1Ω.

6. Troubleshooting

  • No display or erratic readings: Check battery installation and ensure batteries are fresh. Replace if necessary.
  • '1' or 'OL' displayed during resistance measurement: The measured resistance is higher than the selected range. Switch to a higher resistance range.
  • Unstable readings: Ensure all test lead connections are secure and clean. Check that auxiliary earth bars are firmly inserted into the ground and that the ground is sufficiently moist.
  • No response when pressing 'TEST': Ensure the function dial is set to a resistance measurement range and not 'OFF' or 'EARTH VOLTAGE'. Check battery levels.

7. Maintenance

  • Cleaning: Use a soft, dry cloth to clean the exterior of the tester. Do not use abrasive cleaners or solvents.
  • Storage: Store the device in its tool bag in a cool, dry place away from direct sunlight and extreme temperatures.
  • Battery Replacement: When the low battery indicator appears on the display, replace all batteries promptly to ensure accurate measurements. Remove batteries if the device will not be used for an extended period.
  • Calibration: For professional use, periodic calibration by a qualified technician is recommended to maintain accuracy.

8. User Tips

  • Battery Check: If the screen does not work even with new batteries, double-check the battery type and ensure they are inserted with the correct polarity. The device requires both AA and 12V (23A) batteries.
  • Cable Lengths: The provided test cables are 5m, 10m, and 15m. For optimal accuracy in 3-pole measurements, ensure the auxiliary earth bars are placed at appropriate distances (5-10 meters apart) from the main electrode and each other. Using shorter or longer cables than recommended for specific setups might affect results.
  • Ground Condition: For best results, ensure the ground where the auxiliary earth bars are placed is moist. If the ground is very dry, moisten it with water to improve contact.

9. Warranty and Support

This product is covered by a manufacturer's warranty against defects in materials and workmanship. Please refer to the warranty card included in your package for specific terms and conditions. For technical support, troubleshooting assistance, or warranty claims, please contact the seller or manufacturer directly.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.