MEKEDE Suzuki SX4 Car Radio Multimedia System

Contents

MEKEDE Car Multimedia System for Suzuki SX4 (2006-2014) User Manual

Model: Suzuki SX4 Car Radio Multimedia System

1. Introduction

Thank you for choosing the MEKEDE Car Multimedia System. This manual provides detailed instructions for the safe and effective use of your device. Please read all instructions carefully before operation.

Note: Due to continuous product improvement, some descriptions in this manual may differ from the actual equipment. Specifications are subject to change without notice.

1.1. Safety Measures

  • It is forbidden to watch videos or other visual accessories while driving. Active use of the system during driving is not recommended as it can reduce attention and may result in violation of traffic laws and accidents.
  • The unit is designed for use in cars with a 12V power supply and a negative ground. Do not install the system in a bus or truck with an on-board voltage of 24V, as this may cause damage to the device.
  • Use a special cleaning device to care for the screen.
  • To avoid overheating, do not allow direct exposure to sunlight and do not install near the heating system. The operating temperature is between 0°C and 35°C. If the temperature inside the vehicle is too high, cool the interior before switching on the system. It is also not recommended to operate the unit at very low temperatures; wait until the interior and vehicle temperature return to normal.
  • Only use the fasteners provided (screws, mounting frames, etc.) for installation. Using other fasteners may result in damage and is not covered by the warranty.
  • Installation and connection of the device must be performed by a qualified specialist or specially trained staff of a service center.
  • Do not reset to factory settings unless in extreme cases, as this may cause loss of your settings and incorrect operation.
  • Violation of these items and improper use may cause the system to malfunction, in which case warranty service will not be performed.

2. Package Contents

The package includes the following components:

Diagram showing the components included in the package: main unit, power cable, RCA cable, USB cables, reversing camera cable, and GPS antenna.

Description of Package Contents:

  • Machine: The main multimedia head unit.
  • Power Cable: For connecting the unit to the vehicle's power supply.
  • RCA Cable: For audio/video input/output connections.
  • USB Cable: Two USB cables for connecting external devices (M200S M400S models) or three USB cables (M300S M500S M600S M700S models).
  • Reversing Camera Cable: For connecting an optional reversing camera.
  • GPS Antenna: For GPS navigation functionality.
  • Microphone (MIC): External microphone for hands-free calling.

3. Technical Specifications

AttributeSpecification
Mounting Size9"/10"
Screen Resolution1024x600 IPS
Display Size9 inch
CPUUIS7862 1.8GHz 8-core (2 cores ARM cortex A75 + 6 cores ARM cortex A55)
RAMDDR3 2GB/3GB/4GB/6GB/8GB
ROM32GB/64GB/128GB
Operating SystemAndroid 13
Out Power4*45 W
Sound AmplifierTDA 7388/Toshiba 001 (M200S M300S), TDA7851/7850/7838 (M400S M500S M600S M700S)
Chip FM TunerNXP TEF6686
Features of the EqualizerLow Pass Filter, Tone Compensation, Balance Mode, Surround Sound Mode, Extended Equalizer settings (32 bands)
CarPlay / Android AutoSupported (add-on Car Link)
Video FormatRMVB, MKV, MOV, WMV, AVI, MPG, TS, H.264 codec and others.
Audio FormatMP3, WMA, WAV, OGG, FLAC
GPSBuilt-in receiver with external antenna
Software for NavigationSupport
Wi-FiSupport
360° CameraSupport (requires built-in 360 Camera Chip)
BTA2DP and BT address book transfer
Control of Steering Wheel ButtonsSupport
ADAS DVRActivation in the settings menu
AHD HD ReversingAutomatic activation of video input
4G Internet / 4G LTESupport
DSPSupport
Start16c ~ 20c
Voltage during operationDC12V
Voltage at operating range9V ~ 16V
Electric Current15A
Operating Temperature-20°C ~ +70°C
Main Menu LanguageSupport for multiple national languages
CertificationCE

4. Setup and Installation

4.1. Connection Diagram of the Device

Refer to the diagram below for proper wiring connections. Ensure all connections are secure before powering on the unit.

Detailed wiring diagram for the MEKEDE car multimedia system, showing connections for power, speakers, steering wheel control, GPS, and other peripherals.

4.2. Rear Camera Connection Method

The method for connecting the rear camera depends on whether your vehicle uses a CANBUS box.

4.2.1. Without CANBUS Box

Connect the reversing mode control wire to A5. Connect the camera's power supply (12V) to the reverse light of the car. Connect the camera's GND to the car's ground.

Wiring diagram for rear camera connection without a CANBUS box, showing connections to reverse light and ground.

4.2.2. With CANBUS Box

If you have a CANBUS box and the reverse control line (A3 area) is already connected, the yellow line connection for the camera will not be needed. Connect the camera's ACC to A3 ACC. Connect the two red wires of the camera together, but do not connect them with other wires. Connect the camera's GND to the car's ground.

Wiring diagram for rear camera connection with a CANBUS box, detailing ACC and ground connections.

4.3. CANBUS Box Setup

If your car's original functions (e.g., steering wheel control) are not working, you may need to configure the CANBUS type. Before setting up, check your CANBUS photo and select the corresponding type.

Setup Steps:

  1. Connect the CANBUS box as shown in the picture.
  2. Go to Settings > Car Settings > Factory (Password: 8888).
  3. Select the appropriate Car Model and CAN Box type from the options.
Image showing various CANBUS box types and the connection diagram for the CANBUS box.

5. Operating Instructions

5.1. Switching the Appliance On/Off

After switching off the ignition and starting the engine, the multimedia system automatically switches on. The display shows the initial screen. The unit activates automatically after the engine is switched off.

5.2. Touch Screen Operation

This unit features an interactive touchscreen display. Before first use, remove the sealed plastic membrane. Do not use metal or sharply pointed objects, and avoid excessive force.

  • Touch: Click an item to start a plugin or select a menu option.
  • Double Tap: A quick double touch allows you to resize when viewing images.
  • Touch & Hold: Hold an item for 2 seconds to trigger additional actions.
  • Dragging: Touch and hold an item, then drag it across the screen.
  • Moving: Rotate the screen by touching and moving your finger in the desired direction.
  • Scroll Through: Move your finger on the screen in the desired direction and release. Scrolling stops by touching the screen again.

5.3. Front Panel Control

The front panel features physical buttons for common functions:

  • Microphone: For voice input.
  • Emergency Reassembly: Button for emergency equipment.
  • Input/Output Switch/Live Switch/-Sound Switch: Controls audio input/output and sound modes.
  • Return to Main Menu: Navigates back to the main menu.
  • Switching Back to Previous Menu: Returns to the previous screen.
  • Increase Volume: Increases the audio volume.
  • Lower Volume: Decreases the audio volume.

5.4. Main Menu Interface Settings

You can customize the position of icons and freely edit applications on the quick menu bar. You can also change the wallpaper of the main menu interface.

Screenshot of the main menu interface with various app icons and options to change wallpaper.

To Change Wallpaper:

  • Long press on the main menu background.
  • Select 'Change Wallpaper'.
  • Choose from pre-installed wallpapers or images/photos stored on a USB memory device or SD card.

5.5. FM/AM Radio

To access the radio, tap the 'Radio' icon on the main menu. You can manually tune by tapping on the scale bar or use automatic search. The unit supports LOC (local, strong signal only) and DX (all stations) modes, and MONO mode.

Screenshot of the FM RDS Radio interface showing frequency tuning and station presets.

5.6. DSP Processor/Equalizer

Access the equalizer (EQ) by pressing the 'Radio' or 'Equalizer' icon. The built-in DSP chip allows for advanced sound settings.

  • Equalizer Mode: Adjust sound using different frequency settings (Rock, Soft, Jazz, Pop, Classical, Hall). You can adjust the volume of each of the 32 bands. Press 'Standard' to reset all settings.
  • Automatic Volume Mode: Choose recommended settings for listener position (Driver Mode, Passenger Mode, Rear, Center) or adjust independently on the car diagram.
  • Balance Mode: Adjust the volume ratio of speakers for comfortable sound by moving the point on the car interior layout. Supports parametric bass tuning.

5.7. Music / Video Playback

Connect a USB storage device or insert an SD memory card. Press 'Music' for music playback or 'Video' for video playback. The video player supports MP4, AVI, MMV, MOV, MKV, MPEG, RMVB, etc.

Screenshot of the 1080P video playback interface.

Attention: For safety, video playback is restricted while the car is in motion. To view video, stop in a safe place and apply the handbrake.

5.8. Bluetooth (BT) Function

Tap the 'BT' icon in the main menu to enter the hands-free interface. Enable Bluetooth on your phone and search for new devices. Pair your phone with the unit (default PIN: 0000). Once connected, the system screen will show 'connected'.

Screenshot of the Bluetooth function interface showing pairing and call options.
  • Dial: Use the on-screen dial pad to make calls.
  • Contacts: Synchronize your phone book to the device to call contacts directly.
  • BT Music: Listen to music from your mobile phone via Bluetooth connection.
  • Call Log: View outgoing, incoming, and missed calls.

Car Link allows you to use your iPhone or Android device safely in the car for navigation, calls, messages, music, and more.

Diagram showing connection steps for Wireless CarPlay (iOS) and Wired Android Auto.

5.9.1. Wireless CarPlay (iOS System)

  1. Connect your iPhone via Bluetooth.
  2. Tap on 'Car Link'. The phone will ask for authorization; authorize the connection and wait.

5.9.2. Wired Android Auto (Android System)

  1. Connect your Android phone and car DVD player with a USB cable.
  2. Tap on 'Car Link'. The phone will ask for authorization; authorize the connection and wait.

5.10. Split Screen

On the main device screen, you can display two applications simultaneously, such as navigation and music.

To exit split screen mode, pull the icon between the two screens to the right.

5.11. MAP Navigation

The unit features a built-in global positioning system for omnidirectional map display, synchronous real-time traffic display, and fast, accurate positioning. Supported navigation apps include Navitel, IGO, Yandex, and Google.

Screenshot of the GPS navigation interface showing a map with real-time traffic conditions.

5.12. 4G LTE

With 4G LTE connectivity, you can watch live video, listen to music online, play games, and browse the internet at any time. Insert a 4G SIM card into the designated slot.

5.13. Language Settings

To change the system language, go to Settings > Language & Input. Select your desired language and move it to the first position in the preferences list.

5.14. Launcher App Setting

The device features multicolor illumination and can be set to different light modes. Go to Settings > Launcher App Setting to configure.

6. Additional Features (Optional Accessories)

The following features require additional accessories, which must be purchased separately.

6.1. DAB+

DAB+ radio provides better sound quality and stronger signal, primarily for EU countries.

6.2. OBD II

With the OBDII function, you can monitor real-time vehicle data and retrieve fault codes from the vehicle's computer.

Screenshot of the OBDII interface showing engine management diagnostics and tools, including torque, oil fuel speed, and temperature readings.

6.3. TPMS (Tire Pressure Monitoring System)

After correct installation, TPMS sensors automatically monitor tire pressure and temperature, transmitting real-time statistics to the receiver.

Screenshot of the TPMS interface showing tire pressure and temperature for each wheel.

6.4. AV Output

The video output allows rear passengers to watch HD video and audio through a headrest display screen.

6.5. 360° Camera

If you wish to add a 360° camera, it must be ordered along with the car radio, as it requires a built-in 360° Camera Chip on the motherboard.

6.6. ADAS DVR (Advanced Driver-Assistance Systems Digital Video Recorder)

The ADAS DVR provides anti-collision warnings, front vehicle distance prediction, and lane departure warnings to enhance driving safety.

Image illustrating ADAS DVR features like front car start reminder, lane deviation warning, and front distance collision warning.

6.7. AHD HD Reversing

AHD rear-view video offers clearer picture quality compared to ordinary cameras.

Image showing the clear picture quality of AHD reversing video with parking guidelines.

7. Maintenance

To ensure the longevity and optimal performance of your MEKEDE Car Multimedia System, follow these maintenance guidelines:

  • Screen Cleaning: Use a soft, lint-free cloth specifically designed for electronics screens. Do not use abrasive cleaners or solvents. For stubborn smudges, lightly dampen the cloth with water or a screen-cleaning solution.
  • General Cleaning: Wipe the unit's exterior with a soft, dry cloth. Avoid spraying liquids directly onto the device.
  • Temperature Control: Avoid exposing the unit to extreme temperatures. Prolonged exposure to direct sunlight or very cold conditions can affect performance and lifespan.
  • Software Updates: Regularly check for and install firmware and software updates provided by MEKEDE to ensure optimal performance, security, and access to new features.
  • Connection Checks: Periodically inspect all cable connections to ensure they are secure and free from damage. Loose connections can lead to intermittent issues.

8. Troubleshooting

If you encounter a problem, try disconnecting and then reconnecting your device. You can also use the special key to press the Reset button. If these steps do not resolve the issue, refer to the table below. This table will help you solve common problems. If the device still does not work properly, check all connections or consult an authorized dealer.

SymptomProbable CauseSolution
Device does not power on.Ignition key not in "On" position.Turn the key to the "On" position.
Device does not power on.Overheated fuses (15A).Check the circuit breaker in the device. If it's not working, replace it with a good one of the same nominal size.
Device does not power on.Incorrect connection of electrical supply wires (black and yellow).Check the connection of the electrical supply.
Phonebook contacts are not transferred via Bluetooth.No rights on the phone.After connecting the phone to the device, go to the BT settings on the phone and authorize the transfer of the phone book.
Rear camera shows no signal.Incorrect camera wiring or settings.Verify all camera connections and ensure the correct CANBUS settings if applicable.
System heats up after prolonged use.Normal operation within specified temperature range.Ensure proper ventilation around the unit. If the vehicle interior is too hot, cool it down before use.

9. User Tips

Based on common user experiences and questions, here are some helpful tips:

  • CANBUS Box: If your vehicle requires a CANBUS box for features like steering wheel control, ensure it is correctly installed and configured in the factory settings (password 8888). Some models may come with it, others might require separate purchase.
  • Rear Camera Issues: If you experience a 'no signal' message from the rear camera, double-check all RCA cable connections and ensure the camera's power and ground are correctly wired, especially the reverse detecting line.
  • CarPlay/Android Auto: For wireless CarPlay, ensure Bluetooth is connected first. For wired Android Auto, use a reliable USB cable.
  • Language Settings: If the system defaults to a different language, navigate to 'Settings' > 'Language & Input' to change it to English (United States) or your preferred language.
  • System Performance: If the unit feels slow or unresponsive, try optimizing the system through the settings or performing a soft reset.

10. Warranty and Support

MEKEDE products undergo strict quality tests before shipment to ensure high quality.

For any issues or support, please contact MEKEDE Global Store customer service.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.